A brief discussion on the features and characteristics of direct and rapid thermal bitumen melting equipment

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

The modified asphalt equipment estimates the quality and uniformity of various raw materials from the material pile and conveyor at any time. The modified asphalt equipment checks the soil and oversized gravel, and checks whether there is any leakage in the cold hopper. Estimate whether the mixed material is mixed evenly, whether there is white material, whether the oil-stone ratio is reasonable, and check the concrete segregation of the asphalt mixture and the mixed material.
The modified asphalt equipment checks the control parameters of various basic parameters of the mixing device in the control room, the display values ??of the control screen, and the modified asphalt equipment checks whether the data statistics and display values ??of the computer and printout are consistent. Test the raw material heating temperature and the mixed material entry temperature of the modified asphalt equipment.

Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreading truck, check the four thermal oil valves and air pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Try running the asphalt pump and cycle for 5 minutes. If the pump head shell is hot to your hands, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not rotate or make noise. You need to open the valve and continue to heat the asphalt pump until it can operate normally.

During the use of emulsified bitumen equipments, if maintenance is not paid attention to, the cycle will be short, and problems will often occur during use. Only by doing a good job of maintenance can the operation efficiency of the equipment be improved. For example, during maintenance, the following points must be grasped.
It is necessary to regularly check the wear condition of the internal structural components of the mechanical equipment, such as the core feed pipe, the rough jaw plate on the impeller, the cone cap, the wear level of the jaw plate, the rain shield on the circle, and the wear condition. If the wear is more serious, it is necessary to replace or repair it in time. When replacing, it is also necessary to pay attention to the model and specifications, and replace it according to the original components as a reference.

Abstract: Asphalt melting equipment is one of the indispensable equipment in modern road construction. Its main function is to heat a large amount of cold hard asphalt to a suitable working temperature at the construction site. Advanced asphalt melting equipment can greatly improve construction efficiency, reduce human resources and time costs, and ensure pavement quality at the same time.

Emulsified asphalt (ingredients: asphaltene and resin) heating tank is a new type of equipment for heating emulsified asphalt. Its appearance replaces the traditional thermal oil heating equipment, which brings great convenience to our users and improves work efficiency. Then let’s take a detailed look at how it is better than the traditional thermal oil heating equipment.
Emulsified asphalt (ingredients: asphaltene and resin) heating tank is another new type of emulsified asphalt heating storage equipment developed by technically separating the characteristics of traditional thermal oil heating emulsified asphalt tanks and internal heat part (part) rapid emulsified asphalt heating tanks. The automatic circulation program of the asphalt heating equipment enables the asphalt to automatically enter the heater, dust collector, induced draft fan, asphalt pump, asphalt temperature display, water level display, and steam generator as required.
It consists of pipeline and asphalt pump preheating system, pressure relief system steam combustion system, tank cleaning system, oil unloading tank installation, etc. All are installed on the tank body (inside) to form a compact integrated structure. It fully compensates for the shortcomings of traditional thermal oil heating equipment, such as long heating time and high energy consumption.

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.
For the block asphalt melting equipment, the Provincial Environmental Protection Department will review the application materials, and appoint the Provincial Block Asphalt Melting Equipment Management Office to organize relevant doctors to conduct technical evaluation and on-site technical evaluation, and produce expert technical evaluation opinions and on-site inspection reports. Then report the materials of the block asphalt melting equipment to the meeting of directors for scientific research and make a review decision.

Conventional pit repair techniques are mainly hot material repair and cold filling repair, and warm mixing technology is used to ensure compaction, while there are also some special repair methods such as slurry seal/micro-surface material repair

Modified material bitumen stripper, if the definition is simple, is an bitumen stripper. If described in detail, modified materials such as rubber powder or other fillers are added to the bitumen stripper, or an bitumen stripper is used to Block chemical substances such as photooxygen catalysis. The first is to change the chemical composition of the bitumen stripper, and the second is to use modified materials to equip the stripper with a certain spatial network structure, thereby improving its performance. Modified bitumen strippers mainly include vulcanized rubber and thermoplastic polyurethane elastomer modified bitumen strippers, plastic and anti-corrosion coating modified bitumen strippers and polymer modified bitumen strippers.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing station also needs to be powered on for trial operation before it is officially put into work.

The container-type emulsified bitumen equipment hot-melts the base cold-mix colored bitumen and disperses it through the equipment into small cold-mix colored bitumen particles in an aqueous solution containing emulsifier to form a liquid cold-mix colored bitumen material.

When performing bitumen melting, specialized equipment is required. These equipment usually include bitumen melting furnaces, asphalt mixers, asphalt conveying equipment, etc. Among them, the bitumen melting furnace is one of the most advanced equipments, which can heat solid bitumen to liquid state. In addition, asphalt mixers can mix liquid asphalt with stone to make asphalt concrete. , Asphalt conveying equipment can transport asphalt concrete to the construction site. The selection and use of these equipment are of great significance to ensure the quality of bitumen melting and construction efficiency.

According to statistics, among the high-grade highways that have been built and opened to traffic in my country, about 80% are asphalt pavements. However, with the development of time, the influence of various climatic and environmental factors, and the high-intensity driving load, the asphalt pavement will have different degrees of degradation or damage. Pavement maintenance is to take effective technical means to slow down this degradation, so that the pavement can provide good service quality during its service life.

Whether it is the application of modified asphalt equipment or the application of other equipment, if you want to extend its service life, you need to do daily maintenance work. In order to better help everyone, we have modified asphalt The maintenance methods that can be adopted when using the equipment are introduced as follows:

● The spreading amount is accurate, and three overlapping asphalt sprayings can be achieved with good uniformity;
● Intelligent control of spreading amount, real-time monitoring of spreading amount and vehicle speed, closed-loop control;
● Full computer touch screen operation, equipped with video monitoring system, the entire work process can be observed at any time;
● Reliable performance, durability and easy operation;

Fillers used in emulsion bitumen equipment are generally divided into two types: chemically active and non-chemically active. In the production of emulsion bitumen equipment, it can improve the stability of the slurry mixture, speed up or slow down the demulsification speed, and improve the strength of the sealing layer. When adding chemically active fillers, the reaction and compatibility of the fillers with mineral materials and modified emulsion bitumen should be fully considered.

Analysis of the necessity of emulsified bitumen equipment in modern road construction projects With the acceleration of the construction speed of transportation infrastructure, the construction standards are getting higher and higher, and higher requirements are also put forward for the use of emulsified bitumen in the closed layer of fly ash and the adhesive layer between the new and old ground.

The viscosity of the drum bitumen decanter equipment decreases as the temperature increases during the production process. Its output viscosity is about twice as high as every 12°C increase. During production, the base bitumen decanter equipment must first be heated to a liquid state and then emulsified. In order to better integrate the emulsification ability of colloid milling, the viscosity of base bitumen decanter is generally controlled to be about 200 cst. The lower the temperature, the higher the viscosity, which increases the pressure on the bitumen decanter pump and colloid milling, making emulsification impossible: However, on the other hand, in order to prevent the bitumen decanter equipment from weaning when the moisture of the finished product evaporates, it is impossible to heat the base asphalt barrel removal temperature too high, and generally use a colloid grinding inlet and outlet system. The finished product temperature should be below 85°C.

In our daily life, we can often see emulsified asphalt equipment. Its appearance has brought us great convenience. So what is the difference between its modification process? Below, the editor will give you a brief introduction to the relevant knowledge points.
1. Emulsified asphalt equipment first emulsifies and then modifies: This is a relatively simple way to make modified emulsified asphalt. The production process is to grind hot asphalt and emulsifier soap together through a colloid mill to make ordinary emulsified asphalt, and then add latex-like modifiers to the emulsified asphalt through mechanical stirring to make modified emulsified asphalt. The characteristic of this method is that it does not require high equipment.

There are certain standards for the composition and mix ratio of micro-surfacing, and a wide range of materials are used, including polymer-modified emulsified asphalt, various aggregates, cement, water, additives, etc. Raw material quality has a significant impact on microsurfacing performance, so understanding the performance of each component and the key factors that influence its performance is critical to ensuring the quality of your microsurfacing mix.

Friends who are ready to get started have a surprise today. The editor will give you a brief introduction on how to produce emulsified asphalt.

The hydraulic bitumen decanter equipment produced by our company uses thermal oil as the heat carrier and has its own burner for heating. The thermal oil heats, melts, debarks and dehydrates the asphalt through the heating coil. This device can ensure that the asphalt does not age, and has the advantages of high thermal efficiency, fast barrel loading/unloading speed, improved labor intensity, and reduced environmental pollution.

The fine surface is made of stone with a single particle size, which has high wear resistance and anti-slip properties. The construction of the fine surface adopts mechanized construction, which requires less manual labor and has the characteristics of fast construction speed, anti-skid and noise reduction.
The special bonding material for fine surfaces produced by Sinoroader Group has the characteristics of good bonding performance and good durability. The specific construction process is roughly as follows:

In addition to being used according to regulations, modified bitumen equipment should also be maintained regularly in order to effectively extend the service life of modified bitumen equipment. The delivery pump of modified bitumen equipment, as well as its motor and reducer, need to be maintained in accordance with the specifications of the instructions. If the modified bitumen equipment is parked for a long time, the liquid in the tank and pipeline needs to be drained, and each moving component also needs to be filled with grease. The dust in the control box of the modified bitumen equipment needs to be cleaned once every six months. A dust blower can be used to remove dust to prevent dust from entering the machine and damaging parts. The micro powder machine needs to add unsalted butter once for every 100 tons of emulsified bitumen produced.

With the rapid development of our country’s social development and the continuous development of economic and information technology, modern highway construction is also developing rapidly, and the requirements for ground structural materials are becoming higher and higher, and Asphalt concrete bonding raw materials are inseparable from modified asphalt equipment. So besides these influencing factors, what other reasons does the company have that people don’t understand? Let’s analyze it together.
There are some asphalt concrete equipment on the market, because they have not solved the problem of asphalt clogging before grinding, there are not enough preparation equipment and grinding equipment, the structure is unscientific, and the entire grinding process cannot achieve a certain particle size, resulting in modification. The product productivity of asphalt equipment is low and the product quality is unstable. It requires continuous grinding for a long time, creating problems. This will not only greatly increase energy consumption, increase costs, make product quality unstable, and affect the speed of highway construction.

Water is one of the raw materials of the modified asphalt storage tank, and it is distributed in various components of the modified asphalt storage tank equipment. According to the components where water is distributed, the anti-cold measures are explained one by one. The water tank of the modified asphalt storage tank, the water inside the water tank is released through the filter valve. Some instruments of the modified asphalt storage tank do not have a filter valve to save the cost of the equipment. The modified asphalt storage tank can only be drained by loosening the flange bolts at the bottom. The water pump of the modified asphalt storage tank mentioned here includes a hot water pump and a circulating water pump. This type of water pump for the modified asphalt storage tank generally uses a pipeline centrifugal pump. There is a sewage outlet at the bottom of the pipeline centrifugal pump. The modified asphalt storage tank pays attention to the sewage treatment of the sewage outlet at the bottom of the pump. The modified asphalt storage tank emulsion tank generally uses a cone bottom. However, in order to better process the modified asphalt storage tank coefficient, the inlet and outlet are usually not placed at the bottom of the modified asphalt storage tank. Emulsion (mostly water) will remain at the bottom of the tank, and this part of the residual liquid in the modified asphalt storage tank must be discharged through the filter valve at the bottom. Emulsion pump for modified asphalt storage tank There are basically two types of emulsion pumps for modified asphalt storage tank equipment on the market, gear pumps or centrifugal water pumps. Gear pumps can only discharge the liquid inside the pump through the connection flange of the pipeline. The centrifugal water pump for modified asphalt storage tanks uses its own sewage outlet for sewage treatment. The first four items of modified asphalt storage tanks with basic knowledge are basically discharged, and the modified asphalt storage tanks will focus on the latter types. Modified asphalt storage tank colloid mill There will also be residual emulsion or water inside the modified asphalt storage tank colloid mill. The gap between the stator and rotor of the colloid mill is within 1mm. If there is a little residual water in the modified asphalt storage tank, it will cause the accident of frozen modified asphalt storage tank. The residue in the colloid mill can be treated by loosening the connection bolts of the finished product pipeline.

This set of emulsified asphalt production equipment includes water treatment, water storage tanks, water active metering and temperature control systems, asphalt storage tanks, asphalt external temperature systems, hot water pump soap batching systems, soap temporary storage tanks, soap transfer pumps, soap liquid It consists of external temperature system and metering system, filter, hot asphalt transfer pump and metering system, three-stage pipeline emulsifier, emulsified asphalt cooling system and recovery equipment, product tank and electrical automatic control system.
The entire process is modularly designed, and users can freely combine and select according to their needs. The equipment of each part is used as follows: Water treatment system: Mechanical filtration of ordinary tap water absorbs resin exchange reactions, turning high-hardness tap water into pure soft water and reducing water tension. , enhance the emulsification effect of asphalt or modified asphalt.

Preparation items for micro-surfacing slurry sealing: materials, construction machinery (micro-surfacing paver) and other auxiliary equipment.
The micro-surface slurry seal requires emulsified asphalt and stone that meet the standards. The metering system of the micro-surfacing paver needs to be calibrated before construction. The production of emulsified asphalt requires asphalt heating tanks, emulsified asphalt production equipment (capable of producing asphalt content greater than or equal to 60%), and emulsified asphalt finished product tanks. In terms of stone, mineral screening machines, loaders, forklifts, etc. are needed to screen out oversized stones.
The tests required include emulsification test, screening test, mixing test and the equipment and technical personnel required to do these tests.

I believe everyone is familiar with the relevant knowledge about modified bitumen equipment. As users continue to increase its application, we have also talked about it a lot in the above articles and learned that it is mainly engaged in the production of modified bitumen. Production, in order to further enhance users’ understanding of it, professionals summarize its relevant characteristics as follows:

What is the overall operation process of bitumen (composition: asphaltene and resin) drum melting equipment?
The bitumen (composition: asphaltene and resin) drum melting equipment produced by our company mainly uses barrel debarking and melting of large barrels of bitumen (definition: the transformation process of materials from solid to liquid), using high-temperature thermal oil as the material (playing a decision-making role substance), used in supporting facilities of high-temperature thermal oil heating equipment. Bitumen drum melter equipment has the functions of barrel delivery, barrel removal, storage, temperature raising, slag discharge, etc. It is an essential product for high-grade highway construction companies. Bitumen drum melter equipment can be used for resin barrel removal. The bitumen drum melter equipment mainly consists of barrel removal shell, hoisting mechanism, hydraulic booster and electrical control system.