Asphalt Processing

Asphalt concrete mixing equipment generally uses conveyor belt conveyors to transport cold materials. Its main advantages are large conveying capacity, continuous operation, simple equipment structure and automatic control. However, belt deviation is a common fault, which directly affects the drying operation of the drying drum and also affects the production efficiency of the mixing equipment. Therefore, it is very important for the asphalt mixing station to solve the belt deviation problem at the operation site of the asphalt concrete mixing equipment.

1.During the operation of asphalt mixing station equipment, in addition to ensuring that the asphalt mixing station equipment is in good condition, it should also be equipped with a mineral moisture content detector and a finished material tester, and the relevant data should be frequently tested for the operator to adjust the operation in time, so as to keep the equipment in good condition.
2. In addition to affecting production capacity, the moisture content of mineral materials is also the main factor that determines fuel consumption. Additional material sheds should be added.
3. Before operation, all working parts and devices of the asphalt mixing station equipment should be fully checked to see if they are intact and normal. If there is a problem, it must be properly handled before operation, and it is forbidden to operate with illness.

With the strengthening of the trend of environmental protection and energy conservation, the environmental protection of asphalt mixing plants has gradually become the mainstream form of mixing plant development. What kind of equipment can be called an environmentally friendly asphalt mixing plant? What are the basic conditions that must be met?
First of all, as an environmentally friendly asphalt mixing plant, it must meet the requirement of using less energy consumption during use. That is to say, under the conditions of the same quantity and quality, less energy is consumed during the operation process, including various resources such as water and electricity.
Secondly, environmentally friendly asphalt mixing plants not only require less energy consumption, but also must achieve higher production efficiency, while also reducing carbon emissions in the entire production process, so as to meet the proposed low-carbon production requirements

Speaking of asphalt mixing plants, we are not unfamiliar with them. This is a unit equipment specially used for asphalt mixing. In fact, what we really lack understanding of is its gas system. Even the accumulated failures that often occur in the gas system of asphalt mixing plants are not very clear. Facts have proved that only by properly maintaining the various systems of the equipment can efficient production and good benefits be achieved.
The following are four types of gas system failures that often occur in asphalt mixing plants. Let’s analyze the causes of the problems behind the failures one by one.

With the strengthening of the trend of environmental protection and energy conservation, the environmental protection of asphalt mixing plants has gradually become the mainstream form of mixing plant development. What kind of equipment can be called an environmentally friendly asphalt mixing plant? What are the basic conditions that must be met?
First of all, as an environmentally friendly asphalt mixing plant, it must meet the requirement of using less energy consumption during use. That is to say, under the conditions of the same quantity and quality, less energy is consumed during the operation process, including various resources such as water and electricity.
Secondly, environmentally friendly asphalt mixing plants not only require less energy consumption, but also must achieve higher production efficiency, while also reducing carbon emissions in the entire production process, so as to meet the proposed low-carbon production requirements.

Many people think that since both asphalt mixing plants and asphalt mixing plants are equipment for producing asphalt, there should be no difference between them, even if there is, it is only in appearance and volume. However, asphalt mixing plants and asphalt mixing plants are different in even their basic structure and function.
First, let me introduce the basic structure of an asphalt mixing plant, which includes five major components: material supply system, metering system, mixing system, and electrical control system. In comparison, the structure of an asphalt mixing plant is simpler, without so many components, so its operation and maintenance will be simpler.

Due to raw materials or usage, asphalt mixing plants will be subject to a certain degree of wear or other failures during daily use. If they are not controlled or repaired in time, the problem will be further exacerbated. For asphalt mixing plants, what are the ways to prevent wear and failure?
If the asphalt mixing plant is not treated in time after being worn, it may corrode once it is in contact with air, rainwater, etc. for a long time. If the parts of the asphalt mixing plant are severely corroded, the service life and normal operation of the entire equipment will be affected.

The core of the asphalt mixing plant is its electronic control system. If it has problems, it will cause a lot of trouble to use. However, in actual use, the electronic control system in the asphalt mixing plant will inevitably encounter some problems and failures. How to solve it at this time?
If only the instrument display of the electronic control system of the asphalt mixing plant is inaccurate, it means that the weighing system may be affected by external forces; or the drift error of the sensor causes the weighing zero position or weighing interval to change; it may also be caused by sensor damage.

The drying and heating system of the asphalt mixing plant can be regarded as an important part of the whole, so in actual work, it treats the material in a countercurrent heating manner, thereby achieving full dehydration of the cold aggregate, and heating it to a certain temperature, thereby providing the necessary conditions for the normal and continuous operation of the asphalt mixing plant.
During the entire heating process of the asphalt mixing plant, the main purpose is to make the performance of the mixture more in line with the requirements of use, and to make the finished material have good paving performance. Under normal circumstances, the heating temperature of the aggregate is about 160℃-180℃.

The asphalt mixing plant is constructed according to a certain process, which can not only ensure the construction quality, but also ensure that the asphalt mixing plant is not damaged. Although the construction details are critical, the key skills of the asphalt mixing plant construction must be mastered.
Before the construction of the asphalt mixing plant, the top surface of the asphalt mixing plant construction range should be removed, and the dry and flat site elevation should be kept to meet the design requirements. If the ground surface is too soft, the foundation should be reinforced to prevent the construction machinery from becoming unstable and to ensure that the pile frame is vertical.

At present, most asphalt mixing plants have different degrees of energy loss in use, and these losses have brought us serious waste. How to reduce energy consumption in these aspects and achieve efficient production?
First of all, we must first summarize which aspects have energy loss, and then we can find reasonable solutions based on these problems. Through research, it is found that there are four problems in the use of asphalt mixing plants and the production of asphalt mixtures. The content and measures are as follows:
The first aspect is the management of the pile. We can reduce the energy consumption of the asphalt mixing plant through 3 specific methods: 1. Appropriately reduce the stacking height of the pile; 2. Build an inclined pile site with a good drainage structure; 3. Build a waterproof canopy.

In today’s road construction, the use of a large number of road construction machinery represents the entry into the era of highway mechanization. For users, the goal is to use road construction machinery reasonably and tap its potential as much as possible. However, road construction machinery requires various accessories to work together. Now let’s take the asphalt mixing plant as an example to see what commonly used accessories and equipment are available.
Asphalt mixing plant equipment is a relatively complex system, which includes many equipment, mainly nine parts, namely: bag dust removal, finished material temporary storage warehouse, grading machine, fast heating asphalt tank, asphalt barrel removal machine, asphalt recycled material crushing and screening system, coal block crusher, coal mill and dust removal equipment, etc.

Asphalt mixing plants are highly professional equipment with complex systems. It is inevitable that some failures will occur during use. So, what are the common hardware failures of asphalt mixing plants? Do you know?
(I) Because its system is relatively complex, when different components have problems, the problems caused may be different. If during the operation, it is found that the material addition of each silo is inaccurate, this problem may be due to the failure of the sensor of the asphalt mixing plant. At this time, the machine should be stopped for inspection and replaced with a new sensor if necessary. It may also be caused by the jamming of the scale bar. At this time, foreign objects should be removed in time.

Asphalt mixing plants are large-scale products with high professional and technical requirements, and are composed of multiple systems. Among them, asphalt tanks are also a very critical part. Whether it is manufacturing, debugging or installation, it needs to be operated according to the actual application needs of users.
In addition to the manufacturing, debugging and installation, which need to be operated by installers, the maintenance of asphalt tanks in asphalt mixing plants must also be managed by professionals. At the same time, they must strictly follow all safety rules to operate. Before operation, they must be proficient in the relevant requirements and based on the regulations and safety instructions for storing and handling hot asphalt.

In general, the development of my country’s asphalt mixing plant industry is very rapid. In the ton segment, it quickly occupied most of the market share. And with the advancement of technology, it can basically meet the current development needs. However, the total demand for some large-scale asphalt mixing plants has not increased or decreased. What are the reasons?
If we analyze from multiple angles, it is not difficult to find that these reasons are also some of the problems faced by my country’s current asphalt mixing plantindustry. These problems are summarized as follows:

The basic working principle of the green asphalt mixing plants can be roughly summarized in the following ways:
To put it simply, an asphalt plant is actually a set of equipment that can mix several materials according to a predetermined ratio to form a relatively uniform mixture. It is currently widely used and is very important for the construction of different projects. Its performance Various aspects also have a great impact on the engineering quality of asphalt pavement.
Asphalt mixing plant equipment is usually divided into two structures. The intermittent type is relatively more complex in structure and process. The aggregates need to be screened twice and then measured in batches. The batching accuracy is higher. , the mixing quality is good and can meet different construction requirements. The continuous type has a slightly lower accuracy due to its simple structure and simplified operating procedures.

Due to its complexity and importance, asphalt mixing plants are more critical in road construction. Modern asphalt mixing stations have five key systems. Do you know what they are?
1. Mixing system of asphalt mixing plant
Mixing equipment is one of the key systems, why? Usually, the productivity of the mixing equipment has a great impact on the next step of construction efficiency. Most asphalt mixing plants use twin-shaft forced mixing. Since the drying drum and burner of the mixing equipment have strong overload capabilities, and in most cases, the moisture content of the mineral materials is less than 5%, this improves the productivity of the mixing equipment. provide conditions. The mixing blades of the mixer have an adjustable assembly angle and are driven by dual mixing shafts and dual motors.

Construction safety has always been a major issue, and we cannot let any safety hazard go unnoticed. Especially the use of equipment at the construction site. Asphalt mixing stations are prone to failure. Strengthening the maintenance of this equipment is essential to ensure safe construction at the construction site, improve equipment integrity, reduce equipment failures, and ensure the quality of concrete. The role of neglect.
The composition of the asphalt mixing plant is relatively complex, so during maintenance, classified maintenance should be carried out according to the usage and functions of different parts. Maintenance content can be divided into tank maintenance, winch system maintenance and adjustment, stroke limiter adjustment and maintenance, wire rope and pulley maintenance, lifting hopper maintenance, track and track bracket maintenance, etc.

In fact, asphalt mixing stations are not uncommon in our daily lives. They are mainly a unit of equipment specially designed to mix asphalt. What we really don’t understand is the gas system of the asphalt mixing station. Only correct maintenance And operation can bring out the best production effect. So what are the faults in the gas circuit of asphalt mixing station?
The following three points are the more common gas path failures of asphalt mixing stations:

The development prospects of asphalt mixing plants are very good, and the product competition on the market is also very fierce. When the equipment is used, uneven wear of the supporting wheels and wheel rails often occurs, and sometimes there are some abnormal noises and edge gnawing. The main reason is that after the asphalt mixing station has been working for a period of time, the drying cylinder is exposed to high temperature and friction occurs between the supporting wheel and the wheel rail.
Under the action of drying materials in an asphalt mixing station, the equipment will vibrate violently, which will directly lead to improper adjustment of the gap between the wheel rail and the supporting wheel, or mutual interference between the two. The position is skewed, so the operator needs to add grease to the surface contact positions of the supporting wheel and the calibrating wheel rail after every day’s work.

Asphalt damage avoidance mechanism in asphalt mixing plant
1. Asphalt operators should undergo physical examination. Anyone suffering from conjunctivitis, skin disease or allergic reaction to asphalt should not engage in asphalt work.
2. Asphalt operators must apply protective ointment on exposed parts of their skin, and a first aid kit should be provided on the construction site.
3. The factory uniforms and protective equipment of asphalt operators are stored in a centralized manner and are prohibited from being worn home or entering collective dormitories.
4. The transfer of lumpy asphalt should usually be carried out at night and on cloudy days, especially during hot seasons. Small machinery should be used for loading and unloading, and it should not be lifted and transported directly by hand.

Main uses of asphalt mixing plant
Asphalt mixing plant, also called asphalt concrete mixing plant, can produce asphalt mixture, modified asphalt mixture, and colorful asphalt mixture, fully meeting the needs of constructing expressways, graded highways, municipal roads, airports, ports, etc.
The overall composition of asphalt mixing plant
Asphalt mixing equipment mainly consists of batching system, drying system, incineration system, hot material improvement, vibrating screen, hot material storage bin, weighing mixing system, asphalt supply system, powder supply system, dust removal system, product silo and control system, etc. Some composition.

There is also a reversing valve in the asphalt mixing plant, which generally does not cause problems, so I have not understood its solutions in detail before. But in actual use, we encountered this kind of failure. How should we deal with it?
The failure of the reversing valve of the asphalt mixing station is not complicated, that is, the reversing is not timely, gas leakage, electromagnetic pilot valve failure, etc. The corresponding causes and solutions are of course different. For the reversing valve to not change direction in time, it is generally caused by poor lubrication, the spring is stuck or damaged, oil dirt or impurities get stuck in the sliding part, etc. For this, it is necessary to check the status of the lubricator and the quality of the lubricating oil. Viscosity, if necessary, the lubricant or other parts can be replaced.
After long-term use, the reversing valve is prone to wear of the valve core sealing ring, damage to the valve stem and valve seat, resulting in gas leakage in the valve. At this time, the sealing ring, valve stem and valve seat should be replaced, or the reversing valve should be replaced directly. In order to reduce the failure rate of asphalt mixers, maintenance must be strengthened on a daily basis.

Mechanism to avoid asphalt damage in asphalt mixing plant
1. Asphalt operators should undergo physical examination. Anyone suffering from conjunctivitis, skin disease or allergic reaction to asphalt should not engage in asphalt work.
2. Asphalt operators must apply protective ointment on exposed parts of their skin, and a first aid kit should be provided on the construction site.
3. The factory uniforms and protective equipment of asphalt operators are stored in a centralized manner and are prohibited from being worn home or entering collective dormitories.
4. The transfer of lumpy asphalt should usually be carried out at night and on cloudy days, especially during hot seasons. Small machinery should be used for loading and unloading, and it should not be lifted and transported directly by hand.

Road construction machinery is a large range, so let’s talk about one of it, which is the asphalt mixing plant. It is mainly used to produce asphalt, so it is very important among road construction machinery and equipment. An important part, if the quality of the finished product is not good, it will greatly affect the quality of the road. Therefore, below, the editor will use the form of question and answer to guide you to continue learning.

If you look at an asphalt mixing plant from a professional perspective, do you know how to judge its work and significance? In fact, the so-called asphalt mixing station is the one that produces asphalt. We can usually see it in road construction projects. Specifically, it mixes some materials that need to be used during the construction process according to certain proportion requirements. Then complete the corresponding construction work.
Then, we can analyze it from a market perspective. Since it was used in the market, it has been widely praised by users. Today’s asphalt mixing plant technology has been greatly improved, and the entire set of equipment used has a variety of advantages. , such as meeting the requirements of stable control, screening, efficient dust removal, excellent mixing, and green environmental protection during the work process. It is even more obvious when used in large-scale projects such as high-grade highways and airports.

Due to certain restrictions on the current development status and conditions, the profits of the domestic asphalt pavement construction industry are getting lower and lower. Therefore, in the process of using asphalt mixing plants for production, on the one hand, the quality of the products and customer requirements must be ensured. , on the other hand, it is necessary to reduce production costs. Therefore, cost management is very important, and refined management should be implemented in this regard.
First, for device management. Since equipment is the foundation and key of production, in the cost management of asphalt mixing stations, the management of equipment plays an important role in reducing costs. Only by managing the equipment well can the normal working status be ensured, which provides the necessary guarantee for the smooth progress of the project. In fact, in today’s highway projects, equipment costs account for a large part of the cost and profit. The huge profits after the construction of a highway will be greatly affected by the management of materials and equipment.

The quality of the asphalt mixing plant will be a key factor affecting the quality of the project. After reviewing relevant materials related to the production and construction of asphalt concrete, we summarized some cases of failures in asphalt concrete mixing stations during construction and analyzed the reasons.
1. Unstable output and low production efficiency of asphalt mixing plants
(1) Improper proportioning. The mix ratio of asphalt concrete is divided into target mix ratio and production mix ratio. Among them, the target mix ratio controls the cold material transportation ratio of sand and gravel materials, and the production mix ratio is the mixing ratio of various types of sand and stone materials in the finished asphalt concrete materials specified in the design. The production mix ratio is determined by the laboratory, which directly determines the off-site grading standard of the finished asphalt concrete. The target mix ratio is set to further ensure the production mix ratio, and can be adjusted appropriately during production according to the actual situation. When the target mix ratio or the production mix ratio is not appropriate, the stones stored in each measurement of the asphalt mixing station will be disproportionate, with some overflowing and some other materials, unable to be weighed in time, and the mixing cylinder will be idling, resulting in reduced output.

When we operate the asphalt mixing station, we should heat the equipment half an hour in advance, and the clear tank should be heated for at least two hours; and manually operate each part of the equipment to ensure that it is in good operation. status; it is also necessary to conduct relevant inspections on the valves and manually collect and return oil to ensure that the equipment can operate normally.
Several requirements for safe operation of asphalt mixing plants:

We know that the first priority in production is to ensure safety. In the process of operating equipment, staff must always pay attention to using the correct operating methods. Regarding the asphalt mixing plant, it is used to produce asphalt mixtures, modified asphalt mixtures, and colored asphalt mixtures to meet the needs of highways, graded highways, municipal roads, airports, etc.