Asphalt plant control room

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing plant also needs to be powered on for trial operation before it is officially put into work.
The first step in commissioning is to run a single motor and check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

1.During the operation of asphalt mixing station equipment, in addition to ensuring that the asphalt mixing station equipment is in good condition, it should also be equipped with a mineral moisture content detector and a finished material tester, and the relevant data should be frequently tested for the operator to adjust the operation in time, so as to keep the equipment in good condition.
2. In addition to affecting production capacity, the moisture content of mineral materials is also the main factor that determines fuel consumption. Additional material sheds should be added.
3. Before operation, all working parts and devices of the asphalt mixing station equipment should be fully checked to see if they are intact and normal. If there is a problem, it must be properly handled before operation, and it is forbidden to operate with illness.

The asphalt mixing equipment mentioned here may also refer to an asphalt concrete mixing plant. At present, asphalt mixing equipment generally uses a complete set of equipment for mixing. So what are the benefits of using a complete set of equipment?
1. More effective.
In today’s industrial production, a complete set of asphalt mixing equipment can help improve production efficiency and ensure product quality. This is why even in a mixing plant, the equipment used is a complete set of equipment.
2. Ensure quality.
When mixing asphalt, a certain ratio is set. For this type of asphalt liquid used in different occasions, its ratio control has strict requirements. It is necessary to determine its mixing method and mixing time to ensure that the asphalt liquid is consistent with the production site. One of the advantages of a mixing plant is that the quality can be effectively controlled.
3. It can be sampled.
After mixing at the mixing plant, the quality inspector can sample and inspect to ensure that the mixed asphalt liquid meets the use requirements.
In short, asphalt mixing equipment will use a complete set of equipment, mainly to facilitate the later asphalt to meet production needs. Through the mixing plant, the mixing time and feeding sequence can be better controlled, so that the mixed product can meet different use requirements. And after using the archiving equipment, effective spot checks can be carried out, which can better ensure that the quality meets the construction requirements.

The batch asphalt mixing plant is equipped with an automatic cold aggregate feeding system, which consists of a silo, an automatic distributor and a feeding belt conveyor. fully enclosed automatic control has the advantages of stable feeding, fast speed, and improved operation efficiency of the whole station.

The plug valve is a rotary valve in the shape of a closure or plunger. After rotating 90 degrees, the channel opening on the valve plug is the same as or separated from the channel opening on the valve body to complete opening or closing. It is widely used in oilfield excavation, transportation and refining equipment, and such valves are also needed in asphalt mixing plants.
The valve plug of the plug valve in the asphalt mixing plant can be cylindrical or conical. In the cylindrical valve plug, the channel is generally rectangular; in the conical valve plug, the channel is trapezoidal. These shapes make the structure of the plug valve light and very suitable for blocking and connecting media and diversion.

Asphalt is commonly used in our modern urban life, especially in the process of urban highway construction. As an important road surface paving material, the demand for its use is relatively high. Only by using better relevant material performance characteristics can the overall effect be well helped.
Asphalt mixing plants are equipment products that need to be involved in the production and use of such products. With its own excellent performance, it has been better expanded in the promotion of the existing market use scope. The coordination of external use factors is also a key part, and the relationship between various factors must be handled well.

In fact, asphalt mixing stations are not uncommon in our daily lives. They are mainly a unit of equipment specially designed to mix asphalt. What we really don’t understand is the gas system of the asphalt mixing station. Only correct maintenance And operation can bring out the best production effect. So what are the faults in the gas circuit of asphalt mixing station?
The following three points are the more common gas path failures of asphalt mixing stations:

The development prospects of asphalt mixing plants are very good, and the product competition on the market is also very fierce. When the equipment is used, uneven wear of the supporting wheels and wheel rails often occurs, and sometimes there are some abnormal noises and edge gnawing. The main reason is that after the asphalt mixing station has been working for a period of time, the drying cylinder is exposed to high temperature and friction occurs between the supporting wheel and the wheel rail.
Under the action of drying materials in an asphalt mixing station, the equipment will vibrate violently, which will directly lead to improper adjustment of the gap between the wheel rail and the supporting wheel, or mutual interference between the two. The position is skewed, so the operator needs to add grease to the surface contact positions of the supporting wheel and the calibrating wheel rail after every day’s work.

Sinoroader secondary bag filter systems are guaranteed to deliver dust emission levels of less than 20 mg/m³ and enables asphalt plants to be sited in the most environmentally sensitive locations.

Construction safety has always been a major issue, and we cannot let any safety hazard go unnoticed. Especially the use of equipment at the construction site. Asphalt mixing stations are prone to failure. Strengthening the maintenance of this equipment is essential to ensure safe construction at the construction site, improve equipment integrity, reduce equipment failures, and ensure the quality of concrete. The role of neglect.
The composition of the asphalt mixing plant is relatively complex, so during maintenance, classified maintenance should be carried out according to the usage and functions of different parts. Maintenance content can be divided into tank maintenance, winch system maintenance and adjustment, stroke limiter adjustment and maintenance, wire rope and pulley maintenance, lifting hopper maintenance, track and track bracket maintenance, etc.

[1]. Composition of intermittent asphalt mixing plant
The intermittent asphalt mixing plant mainly consists of cold material silo, cold material distribution system, cold material conveying system, combustion and drying system, ventilation and dust removal system, hot material elevator, vibrating screen, hot material silo, powder conveying system and asphalt conveying system. System, metering system, mixing cylinder, control system, finished material transportation and storage system, asphalt heating and insulation system, etc.
2. Discussing the phenomenon of warehouse cascading in asphalt concrete mixing plants
2.1 First, let’s introduce the structure and principle of vibrating screen. The main components include: RetentionRubber, SupportTube, vibrating screen drive system and supporting electrical components
The working principle is introduced as follows: hot aggregate is sent to the vibrating screen through the hot aggregate elevator, and the hot aggregate is vibrated and screened by the vibrating screen. Stones of different specifications enter their corresponding hot aggregate bins through the screen and cannot pass through the geotechnical work. The super-sized particles from the cloth screen enter the overflow bin and are sent out.

The application of asphalt mixing plants also involves selection issues. In order to give full play to the performance of the equipment, the model of the machine is mainly determined according to the actual situation of the construction site. It sounds relatively simple, but some details still need to be emphasized.
The so-called specific conditions of the construction site first include the size of the site; secondly, the properties, specifications and working dimensions of the enterprise’s supporting equipment. It is necessary to try to do a good job in all aspects to help improve production efficiency and ensure product quality. In the case of intensive network management, the network management function of the asphalt mixing plant must also be taken into account to avoid difficulties in future upgrades.

When inspecting the asphalt mixing plant, it was found that the asphalt in the pipeline solidified because the temperature of the asphalt transportation pipeline did not meet the requirements. Analysis believes that the reasons for this result are that the high-level oil tank of the heat transfer oil is too low, resulting in poor circulation of the heat transfer oil; the second is that the inner tube of the double-layer pipe is eccentric; the third is that the heat transfer oil pipeline is too long; and the fourth is that the heat transfer oil pipeline is not insulated measure.

With the strengthening of the trend of environmental protection and energy conservation, the environmental protection of asphalt mixing plants has gradually become the mainstream form of mixing plant development. What kind of equipment can be called an environmentally friendly asphalt mixing plant? What are the basic conditions that must be met?
First of all, as an environmentally friendly asphalt mixing plant, it must meet the requirement of using less energy consumption during use. That is to say, under the conditions of the same quantity and quality, less energy is consumed during the operation process, including various resources such as water and electricity.
Secondly, environmentally friendly asphalt mixing plants not only require less energy consumption, but also must achieve higher production efficiency, while also reducing carbon emissions in the entire production process, so as to meet the proposed low-carbon production requirements.

Mobile Cold Aggregate Feeding System

The asphalt plant control room is used to control the asphalt material and working mode

The quality of asphalt mixture directly determines the quality of asphalt pavement engineering. This article discusses the key points of supervision of ordinary highway asphalt plants in order to better monitor the quality of asphalt mixture.

Asphalt mixing stations and equipment must implement secondary leakage protection measures. They can only be used after being plugged in and operated through the circuit breaker before use. During the trial operation, it is necessary to verify that the rotational speed of the mixing drum will be inappropriate.

In my country, most of the raw materials used in highway construction are asphalt, so asphalt mixing plants have also developed rapidly. However, under the situation of rapid economic development in my country, the problems of asphalt pavement have gradually increased, so the market requirements for asphalt quality have become higher and higher.
There are many factors that affect the quality of asphalt. In addition to the need for asphalt mixing plant equipment to meet conventional requirements, the ratio of raw materials is also very important. At present, my country’s existing industry specifications indicate that the maximum particle size of the asphalt mixture used on the upper layer of the highway cannot exceed half of the thickness, and the maximum particle size of the aggregate of the middle asphalt mixture cannot exceed two-thirds of the thickness of the layer, and the maximum size of the structural layer cannot exceed one-third of the same layer.

With the changes in society and the transformation of the economy, real estate and construction are developing rapidly. When building and constructing houses, most of them use some equipment, such as mixing plants. The asphalt mixing plants produced by our company have a high level of mechanization and high production efficiency.
What is an asphalt mixing plant? It is a combined device used for centralized mixing of concrete, also known as a concrete prefabrication site.
With the development of municipal construction, the use of centralized mixing and the provision of commercial mixing plants have great advantages, so it has developed rapidly and created conditions for promoting concrete pumping construction and realizing the joint operation of mixing, conveying and pouring machinery. It is mainly composed of five major systems, including a mixing host, a material weighing system, a material conveying system, a material storage system and a control system, as well as other ancillary facilities. However, there are some faults in normal times. What are the specific ones in the gas source failure?

Asphalt mixing plant, also known as asphalt concrete mixing plant, asphalt mixing equipment. Refers to a complete set of equipment used for mass production of asphalt concrete. According to the mixing method, it can be divided into intermittent type and continuous type; according to the transportation method, it can be divided into fixed type, semi-fixed type and mobile type.

Due to its complexity and importance, asphalt mixing plants are more critical in road construction. Modern asphalt mixing stations have five key systems. Do you know what they are?
1. Mixing system of asphalt mixing plant
Mixing equipment is one of the key systems, why? Usually, the productivity of the mixing equipment has a great impact on the next step of construction efficiency. Most asphalt mixing plants use twin-shaft forced mixing. Since the drying drum and burner of the mixing equipment have strong overload capabilities, and in most cases, the moisture content of the mineral materials is less than 5%, this improves the productivity of the mixing equipment. provide conditions. The mixing blades of the mixer have an adjustable assembly angle and are driven by dual mixing shafts and dual motors.

What should I do when the reversing valve in the asphalt mixing plant fails? The editor has a trick:
1. The reversing valve cannot be reversed or the reversing action is slow, which is generally caused by poor lubrication, stuck or damaged springs, oil or impurities stuck in the sliding parts. In this regard, you should first check whether the oil mist is working normally; whether the viscosity of the lubricating oil is appropriate. If necessary, the lubricating oil should be replaced, the sliding part of the reversing valve should be cleaned, or the spring and reversing valve should be replaced.

Asphalt mixing equipment is also divided into fixed and mobile types. There are still big differences between the two to a certain extent. Let’s take a look at the design of mobile asphalt mixing equipment. What advantages can bring to the equipment?

Asphalt mixing plant is a very practical engineering machinery. Especially in the road construction process, it plays an irreplaceable role. Due to its importance, in addition to ensuring its own quality, the use and maintenance of the equipment must be carried out normally. Let’s learn about the daily maintenance requirements of asphalt mixing plants.

Main uses of asphalt mixing plant
Asphalt mixing plant, also called asphalt concrete mixing plant, can produce asphalt mixture, modified asphalt mixture, and colorful asphalt mixture, fully meeting the needs of constructing expressways, graded highways, municipal roads, airports, ports, etc.
The overall composition of asphalt mixing plant
Asphalt mixing equipment mainly consists of batching system, drying system, incineration system, hot material improvement, vibrating screen, hot material storage bin, weighing mixing system, asphalt supply system, powder supply system, dust removal system, product silo and control system, etc. Some composition.

Asphalt mixing plant, also known as asphalt concrete mixing plant, is a complete set of equipment for batch production of asphalt concrete. Its efficient and stable operation is of great significance to ensure the quality of the project. It is mainly used in the construction of highways, grade roads, municipal roads, airports, ports and other projects. According to the mixing method, asphalt mixing plant can be divided into forced intermittent type and continuous production type; according to the transportation method, it can be divided into fixed type, semi-fixed type and mobile type.
The working principle of asphalt mixing plant mainly includes steps such as aggregate processing, asphalt processing and mixture mixing. Specifically, aggregates (such as gravel, crushed stone, etc.) are sent to aggregate bins through conveyors or bucket elevators, and then measured by aggregate metering devices, and a certain amount of aggregates are sent to sub-bins. Asphalt is stored in asphalt bins or oil storage tanks, and is measured by asphalt metering devices, and a certain amount of asphalt is sent to asphalt sub-bins. Finally, according to the ratio requirements, different aggregates are taken out from their respective sub-bins and sent to the mixture mixer through conveyors or bucket elevators for mixing.