Briefly describe how to improve the heating system of asphalt mixing plant

Asphalt mixing station is one of the most important equipment in processing operations, so how to build a website has become the focus of people’s attention. The editor has compiled some key points, hoping to be helpful to everyone.

As an important production equipment in construction, asphalt mixing plant has high production investment. Therefore, production is very important during use, but daily maintenance is also very important. In addition to regular maintenance, routine maintenance is also essential. The editor of Asphalt Mixing Plant shares some key points of daily maintenance and scheduled maintenance;

Asphalt mixing equipment is also divided into fixed and mobile types. There are still big differences between the two to a certain extent. Let’s take a look at the design of mobile asphalt mixing equipment. What advantages can bring to the equipment?

Road construction machinery is a large range, so let’s talk about one of it, which is the asphalt mixing plant. It is mainly used to produce asphalt, so it is very important among road construction machinery and equipment. An important part, if the quality of the finished product is not good, it will greatly affect the quality of the road. Therefore, below, the editor will use the form of question and answer to guide you to continue learning.

The mixing speed of asphalt mixing plant equipment is indeed very fast, and the corresponding mixing power must be very high, but the specific amount must be measured in a certain way to determine the scope of use of asphalt mixing equipment. There are many methods to measure the mixing power of asphalt mixing equipment, but the relatively small errors are the motor counter-torque measurement method and the strain measurement method.
When the motor of the asphalt mixing equipment starts running, the electromagnetic moment acting on the motor rotor and the electromagnetic moment acting on the motor stator are equal, but their directions are opposite. Therefore, as long as the torque acting on the stator is measured, the torque on the rotor can be obtained, and the actual mixing torque is obtained after deducting the friction torque on the rotor bearing.
On the premise of knowing the torque and mixing speed, the mixing power of the asphalt mixing equipment can be calculated. This is the so-called motor counter-torque measurement method, which is relatively simple and suitable for smaller mixing systems.

When inspecting the asphalt mixing plant, it was found that the asphalt in the pipeline solidified because the temperature of the asphalt transportation pipeline did not meet the requirements. Analysis believes that the reasons for this result are that the high-level oil tank of the heat transfer oil is too low, resulting in poor circulation of the heat transfer oil; the second is that the inner tube of the double-layer pipe is eccentric; the third is that the heat transfer oil pipeline is too long; and the fourth is that the heat transfer oil pipeline is not insulated measure.

The quality of the asphalt mixing plant will be a key factor affecting the quality of the project. After reviewing relevant materials related to the production and construction of asphalt concrete, we summarized some cases of failures in asphalt concrete mixing stations during construction and analyzed the reasons.
1. Unstable output and low production efficiency of asphalt mixing plants
(1) Improper proportioning. The mix ratio of asphalt concrete is divided into target mix ratio and production mix ratio. Among them, the target mix ratio controls the cold material transportation ratio of sand and gravel materials, and the production mix ratio is the mixing ratio of various types of sand and stone materials in the finished asphalt concrete materials specified in the design. The production mix ratio is determined by the laboratory, which directly determines the off-site grading standard of the finished asphalt concrete. The target mix ratio is set to further ensure the production mix ratio, and can be adjusted appropriately during production according to the actual situation. When the target mix ratio or the production mix ratio is not appropriate, the stones stored in each measurement of the asphalt mixing station will be disproportionate, with some overflowing and some other materials, unable to be weighed in time, and the mixing cylinder will be idling, resulting in reduced output.

Asphalt mixing stations are constructed according to a certain process, which can not only ensure the construction quality, but also ensure that the asphalt mixing station is not damaged. Although construction details are critical, the key skills of asphalt mixing station construction must be mastered.
Before the construction of the asphalt mixing plant, the top surface of the asphalt mixing station construction range should be removed, and the site elevation should be kept dry and flat to meet the design requirements. If the surface is too soft, the foundation should be reinforced to prevent the construction machinery from losing stability and ensure that the pile frame is vertical.
Then the on-site construction machinery should be inspected to ensure that the machinery is intact and assembled and tested under the premise of meeting the requirements. To ensure the verticality of the asphalt mixing plant, the deviation of the gantry guide and the mixing shaft from the verticality of the ground shall not exceed 1.0%. Asphalt mixer manufacturer.

Due to raw materials or usage, asphalt mixing plants will be subject to a certain degree of wear or other failures during daily use. If they are not controlled or repaired in time, the problem will be further exacerbated. For asphalt mixing plants, what are the ways to prevent wear and failure?
If the asphalt mixing plant is not treated in time after being worn, it may corrode once it is in contact with air, rainwater, etc. for a long time. If the parts of the asphalt mixing plant are severely corroded, the service life and normal operation of the entire equipment will be affected.

Asphalt mixing stations play an important role in road construction. This article starts from the site selection, commissioning, and acceptance of the asphalt mixing plant, and elaborates on comprehensive and reasonable planning to avoid disturbing the normal construction order.

As a special equipment, standardizing the operating procedures of important production tools of asphalt mixing stations, conducting daily maintenance, regular inspections, eliminating hidden dangers, etc. can effectively ensure the safety and stability of the equipment and prevent equipment from malfunctioning due to misoperation. causing equipment damage. Good maintenance operations can also greatly extend the service life of asphalt mixing plants. Therefore, before daily operation, the asphalt mixing plant must be properly maintained to make the asphalt mixing plant operate better and create wealth.

The driving device is one of the important components of the asphalt mixing plant, so whether it can operate reliably must be highly valued to avoid adverse effects on the entire asphalt mixing plant. In order to ensure that the driving device in the asphalt mixing plant is indeed complete and reliable, the following maintenance measures are essential.

Synchronous gravel sealing in road maintenance can quickly improve road driving performance, repair anti-skid performance, smoothness, etc. It is used in preventive maintenance and is also one of the methods of low-grade road pavement construction. Synchronous gravel seal has the advantages of high strength, rough surface, non-slip, impermeable, good durability, and prevention of water mist when driving on rainy days. The so-called synchronous gravel sealing layer is to use special equipment, namely the synchronous gravel sealing truck and the bonding material (modified asphalt or modified emulsified asphalt) to be spread simultaneously on the road surface, and the single layer of asphalt wear is formed by natural driving or rolling with a road roller. layer, mainly used as asphalt surface layer.

Asphalt mixing station is the standard for mixing asphalt. Having said that, many people still think that this has nothing to do with us. We don’t use asphalt, but do you know that our roads are made of asphalt? When I was a child, I used asphalt to pluck pig hair. The hair on the pig’s head was indeed clean. When using asphalt, it must be burned hot, because if it is cold, it will be very hard and cannot be used. Therefore, if a large amount of asphalt is needed, there must be an asphalt mixer because there is no more convenient equipment than it.
What kind of source material is asphalt that requires special equipment. Asphalt is a black-brown, high-viscosity organic liquid composed of hydrocarbons and non-metallic substances of different molecular weights. The surface is black and soluble in carbon disulfide. At the same time, it is also a waterproof, moisture-proof and anti-corrosion organic gelling material. It can be mainly divided into three types: coal tar asphalt, petroleum asphalt and natural asphalt. Asphalt is mainly used in industries such as coatings, plastics, rubber, and paving roads.

Asphalt flue gas treatment methods, their principles and characteristics, and an asphalt flue gas environmental protection treatment plan based on the actual asphalt flue gas problems faced by the unit.

1. Basic situation
My unit’s mixing plant is equipped with a 4000-type asphalt mixing plant. During daily production of the asphalt mixing plant, a large amount of asphalt smoke will be emitted from the mixing pot discharge port. This smoke not only has an unpleasant smell, but also contains A large number of compounds that are harmful to the human body, such as benzopyrene, benzanthracene, carbazole and other polycyclic aromatic hydrocarbons, mostly have carcinogenic risks. Smoke overflow will cause pollution to the surrounding atmospheric environment and affect the personal health of workers. Although the overflow port of the mixing station is equipped with a dust retaining wall, the fine dust is seriously raised, and the cold material belt conveyor is dusty. In order to protect the environment, reduce pollution, and reduce cost investment, based on full research and absorption of technology in the same industry, and combined with the actual situation of asphalt mixing, we are planning to install asphalt mixing bag dust collectors to the flue at the discharge port of the mixing pot to control asphalt fumes. Gas is processed. The dust removal efficiency of the bag dust collector can reach 97%~99%, and the dust-containing gas can be purified to a level of 50mg/Nm3.

Speaking of asphalt mixing plants, we are not unfamiliar with them. This is a unit equipment specially used for asphalt mixing. In fact, what we really lack understanding of is its gas system. Even the accumulated failures that often occur in the gas system of asphalt mixing plants are not very clear. Facts have proved that only by properly maintaining the various systems of the equipment can efficient production and good benefits be achieved.
The following are four types of gas system failures that often occur in asphalt mixing plants. Let’s analyze the causes of the problems behind the failures one by one.

Asphalt mixing plant is a complete set of equipment composed of many systems. It is widely used in the current society. Its components include batching system, drying system, combustion system, hot material lifting, weighing and mixing system and control system.
In the process of asphalt mixing, heating is an indispensable link, because there must be a system for heating in the asphalt mixing station, but the system generally fails for various reasons. So how should the heating system of the asphalt mixing station be improved? This article will briefly explain this issue.
Generally speaking, when the asphalt mixing station is running under low temperature conditions, the asphalt circulation pump and spray pump cannot operate normally, which will cause the asphalt in the asphalt scale to solidify, and then the asphalt mixing station cannot be produced. Therefore, the asphalt mixing station needs a heating system during operation.

In general, the development of my country’s asphalt mixing plant industry is very rapid. In the ton segment, it quickly occupied most of the market share. And with the advancement of technology, it can basically meet the current development needs. However, the total demand for some large-scale asphalt mixing plants has not increased or decreased. What are the reasons?
If we analyze from multiple angles, it is not difficult to find that these reasons are also some of the problems faced by my country’s current asphalt mixing plantindustry. These problems are summarized as follows:

1: The site should be located on higher ground and away from residential areas and densely populated areas.
2: The venue should consider the transportation distance and choose a location with convenient transportation.
3: Determine the website construction plan according to the terrain

Determining the material is a necessary stage in the design process of asphalt mixing equipment, and it is also one of the most critical links, because the material will be directly related to the use effect and service life of the entire equipment. Generally, when we determine the machine material, we usually base it on the characteristics of the working medium, and the same is certainly true for asphalt mixing equipment.

It is inevitable that the asphalt mixing plant will have insufficient pumping force during use. In fact, during the construction process, as long as the asphalt mixing station is operated in accordance with regulations, and the accessories are cleaned and replaced in time, the asphalt mixing plant will generally not have insufficient pumping force. Now the editor of the asphalt mixing station manufacturer briefly introduces the common solutions to insufficient pumping force of asphalt mixing plant as follows.

Asphalt mixing equipment has a special function, which is that it can perform cyclic heating to make the asphalt product reach the best condition. But how does it achieve this function? Everyone is curious about this.

In the 21st century, with the booming development of modern engineering construction, complex integrated supporting equipment has been invested in large quantities. Its complex process and more independent operating components have relatively high requirements for the performance of its equipment control system. The application of PLC in asphalt mixing station realizes the control of the entire process of asphalt mixing station, which facilitates the construction of modern engineering construction. Therefore, this article discusses and analyzes the application of PLC in asphalt mixing station, which has certain economic value and practical significance.

Judging from the situation of highways in our country, asphalt pavement is the most used, which is one of the reasons why asphalt mixing plants have developed so rapidly. Under the situation of rapid economic development, the quality problems of asphalt pavement are gradually increasing, which puts forward higher and higher requirements for the quality of asphalt. It is understood that the primary factor that affects the quality of asphalt is the ratio of raw materials. This is also covered in the introduction of asphalt mixing stations. You can discuss it together.
In order to obtain high-quality asphalt products, in addition to the asphalt mixing equipment meeting the requirements, selecting the appropriate asphalt mixture gradation type is also a top priority. According to my country’s current regulations, the maximum particle size of the asphalt mixture in the upper layer of the highway should not exceed half of the layer thickness; while the maximum particle size of the aggregate in the middle surface layer of asphalt mixture should not exceed two-thirds of the layer thickness; and the asphalt layer should not exceed half of the layer thickness. The maximum nominal aggregate size of the pavement structural layer mixture should not exceed one-third of the layer thickness.
Based on this analysis, if an asphalt surface layer with a certain thickness is selected according to the above specifications, the particle size of the asphalt mixture aggregates will generally be larger, which will inevitably bring insurmountable construction difficulties to the construction of asphalt concrete pavement. After investigation, testing, analysis, and comparison, it can be seen that the lower layer has a wider choice, so the AG-201 gradation type can be used; while the selection of the upper layer mixture type is more difficult, and it is necessary to achieve a reasonable choice of this mix ratio. , on the one hand, we must examine as many aggregate resources as possible, and on the other hand, we must also consider the model of the mixing equipment.
In order to ensure the quality of the project, strict selection and inspection of engineering materials must be carried out. Therefore, the selection and determination of raw materials should be based on the requirements for pavement structure and use quality, combined with the supply of floor materials, and inspection in accordance with the requirements of relevant test procedures, and then Select the best materials so that all technical indicators of the materials meet the specified technical requirements.

Any kind of mechanical equipment must go through precise design, testing and other processes before it can be manufactured, and the same is true for asphalt mixing stations. According to the survey, the following stages are necessary for any asphalt mixing plant.
First of all, the main technical parameters of the product to be designed must be determined according to market needs, so construction market research, data analysis and other links are indispensable. Secondly, the ideal working principle and the plan to realize this principle will be determined through innovative conception and optimization screening. , a schematic diagram of the overall design scheme should also be given.

Asphalt is commonly used in our modern urban life, especially in the process of urban highway construction. As an important road surface paving material, the demand for its use is relatively high. Only by using better relevant material performance characteristics can the overall effect be well helped.
Asphalt mixing plants are equipment products that need to be involved in the production and use of such products. With its own excellent performance, it has been better expanded in the promotion of the existing market use scope. The coordination of external use factors is also a key part, and the relationship between various factors must be handled well.

Asphalt mixing plant is a relatively important complete set of equipment in people’s lives. There are many components of this equipment, such as grading machine, vibrating screen, belt feeder, powder conveyor, elevator and other parts. Plug valve is one of them, so what is the specific role of plug valve in asphalt mixing plant? This article will give a brief introduction.
The plug valve is first of all a closure or plunger-shaped rotary valve. Generally, it is necessary to rotate 90 degrees to make the channel opening on the valve plug the same as that on the valve body, or to split it to play the role of opening or closing. The shape of the plug valve in the asphalt mixing plant is generally cylindrical or conical.

Many people think that since both asphalt mixing plants and asphalt mixing plants are equipment for producing asphalt, there should be no difference between them, even if there is, it is only in appearance and volume. However, asphalt mixing plants and asphalt mixing plants are different in even their basic structure and function.
First, let me introduce the basic structure of an asphalt mixing plant, which includes five major components: material supply system, metering system, mixing system, and electrical control system. In comparison, the structure of an asphalt mixing plant is simpler, without so many components, so its operation and maintenance will be simpler.