Circuit fault maintenance of SBS bitumen emulsification plants

Synchronous chip seal is a process technology for treating cracks in asphalt pavement, and it is currently a highway construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical characteristics are? If you don’t know, follow the editor of Sinoroader company to have a look.

With the development of science and technology, the emergence of emulsified asphalt tanks has brought great convenience to our work, and is widely used in every site. So what issues need to be paid attention to when filling emulsified asphalt tanks? Below, the editor will introduce to you the relevant knowledge structure diagram, hoping to be of some help to you.

Due to the incorporation of a certain proportion of water into the slurry sealing mixture, it is easy to evaporate in the air. After the water is evaporated, it will become dry and hardened. Therefore, after the slurry is formed, it not only looks very similar to fine-grained asphalt concrete, but does not affect the visual appearance of the road. It also has the same technical properties as fine-grained concrete in terms of wear resistance, anti-skid, waterproofing, and smoothness. Slurry seal technology is used in highway pavement maintenance because of its simple construction technology, short construction period, low cost, high quality, wide application, strong adaptability, etc. It is an asphalt with both economy and high efficiency. Pavement maintenance technology is worthy of application and promotion.

The base layer of asphalt pavement is divided into semi-rigid and rigid. Since the base layer and the surface layer are materials of different properties, good bonding and continuity between the two are the key requirements for this type of pavement. In addition, when the asphalt surface layer seeps water, most of the water will be concentrated at the joint between the surface layer and the base layer, causing damage such as slurry, looseness, and potholes to the asphalt pavement. Therefore, adding a lower seal layer on top of a semi-rigid or rigid base layer will play a vital role in enhancing the strength, stability and waterproofing capabilities of the pavement structural layer. The more commonly used one is to use asphalt gravel synchronous sealing technology.
So let’s take a look at how the construction of the asphalt gravel synchronous sealing truck is carried out:

Contemporary roads and pavements have undergone many changes: traffic volume and driving frequency have increased significantly, the axle load of logistics trucks has continued to increase, one-way driving in separate lanes has been widely implemented, and regulations have further improved the anti-flow resistance of the ground, that is, the work of modified asphalt equipment under high temperatures ability;

The fine surface is made of stone with a single particle size, which has high wear resistance and anti-slip properties. The construction of the fine surface adopts mechanized construction, which requires less manual labor and has the characteristics of fast construction speed, anti-skid and noise reduction.
The special bonding material for fine surfaces produced by Sinoroader Group has the characteristics of good bonding performance and good durability. The specific construction process is roughly as follows:

Bitumen emulsifier is a surfactant. A surfactant is a compound that reduces the surface tension between two liquids, a gas and a liquid, or a solid and a liquid. Surfactants are mainly used in: detergents, detergents, fabric softeners, wetting agents, emulsifiers, foaming agents, dispersants, adhesives, etc.

Synchronous gravel sealing technology refers to the use of special synchronous gravel sealing truck equipment to lay and roll prepared gravel, asphalt and other materials to build a single layer of asphalt gravel wearing layer, which is important for highway pavement. protection of. From the perspective of characteristics, it is simple and easy to implement. It has obvious effects on the prevention of highway diseases, problem solving, later maintenance, and improvement of grade protection. It can also well extend the service life of highways.

This set of mechanical equipment includes wastewater treatment, water storage tank, automatic water measurement and verification temperature control system, asphalt storage tank, asphalt external temperature system, hot water pump soap condiment system, soap storage tank, soap mixing pump, soap external It is composed of temperature system and measurement verification system, filtration system, hot asphalt mixing pump and measurement verification system, three-stage pipeline-type black antistatic medical tweezers, emulsified asphalt cooling system and retrieval machinery, and automatic control system for commercial tanks and electrical equipment.

The selection of asphalt melting equipment should take into account factors such as the use environment, working conditions, and technical requirements. Common ones include hot oil heating equipment, electric heating equipment, and gas heating equipment.
Hot oil heating equipment is suitable for occasions that require long-term heating and high temperature control accuracy;
Electric heating equipment is suitable for small projects or occasions where temperature control accuracy is not required;
Gas heating equipment has the advantages of simple operation and low cost, but safety protection measures must be strictly followed.
When choosing, it is also necessary to comprehensively consider factors such as economy and environmental protection.

There are many ways to heat bitumen, including using fire source heating, electric heating, steam heating, hot water heating and indirect heating. Fire source heating generates heat by burning fuel to heat the bitumen to a molten state. Electric heating converts electrical energy into thermal energy through electric heating elements to heat the bitumen to a molten state. Steam heating transfers heat to bitumen through steam, heating the bitumen to a molten state. Hot water heating transfers heat to the bitumen through hot water, heating the bitumen to a molten state. Indirect heating transfers heat to the heating medium, which then transfers the heat to the bitumen to heat the bitumen to a molten state.

I believe that many people already know about synchronous gravel sealing. But when asked under what circumstances synchronous gravel sealing is suitable, many people cannot tell.
Under what circumstances is synchronous gravel sealing more suitable? According to the technical specifications for the construction of simultaneous gravel sealing, simultaneous gravel sealing can be used for the following disease types:

In addition to being used according to regulations, modified bitumen equipment should also be maintained regularly in order to effectively extend the service life of modified bitumen equipment. The delivery pump of modified bitumen equipment, as well as its motor and reducer, need to be maintained in accordance with the specifications of the instructions. If the modified bitumen equipment is parked for a long time, the liquid in the tank and pipeline needs to be drained, and each moving component also needs to be filled with grease. The dust in the control box of the modified bitumen equipment needs to be cleaned once every six months. A dust blower can be used to remove dust to prevent dust from entering the machine and damaging parts. The micro powder machine needs to add unsalted butter once for every 100 tons of emulsified bitumen produced.

The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) Open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

1. Preparation before construction
2. Mix
3. Paving
4. Leveling
5. Shutdown
6. Overlap
7. Crush

When using asphalt melting equipment, you need to pay attention to the following points:
1. The power must be cut off during installation and operation to ensure safety.
2. Before starting operation, check whether all components are normal and have no fault prompts. In particular, the inspection of key parts such as the heater part and the conveyor belt device is particularly important.

Each F1 track must be paved with three layers of asphalt, middle and lower, of which the lowest layer is 10 cm coarse asphalt concrete bearing layer, its flatness is less than 8 mm; In the middle is a 4 cm medium grained asphalt concrete bond layer, its flatness is less than 5 mm; The top layer uses 4 cm modified asphalt mixture as the surface wear layer, and the flatness is less than 2 mm.

The paved F1 track cannot have more than 3 points per kilometer of flatness detection, which is much higher than the highway.

Asphalt mixture is a kind of composite material, mainly composed of asphalt, coarse aggregate, fine aggregate, mineral powder, some also added polymer and wood cellulose; By these different quality and quantity of materials mixed to form different structures, and have different mechanical properties

Asphalt spreading trucks are used to spread the permeable oil layer, waterproof layer and bonding layer of the bottom layer of asphalt pavement on high-grade highways. It can also be used in the construction of county and township-level highway asphalt roads that implement layered paving technology. It consists of a car chassis, an asphalt tank, an asphalt pumping and spraying system, a thermal oil heating system, a hydraulic system, a combustion system, a control system, a pneumatic system, and an operating platform.

● The spreading amount is accurate, and three overlapping asphalt sprayings can be achieved with good uniformity;
● Intelligent control of spreading amount, real-time monitoring of spreading amount and vehicle speed, closed-loop control;
● Full computer touch screen operation, equipped with video monitoring system, the entire work process can be observed at any time;
● Reliable performance, durability and easy operation;

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.

The heating principle of asphalt decanter equipment is to heat, melt and decanter the asphalt through the heating plate. It is mainly composed of de-barreling box, lifting system, propeller and electrical control system.
The box of asphalt decanter plant is divided into upper and lower chambers. The upper chamber is the asphalt melting chamber, which is densely covered with heat transfer oil heating coils or hot air heating pipes. The asphalt is melted and removed from the barrel by heat. The hoisting hook is installed on the gantry, and a barrel grabber is hung. The asphalt barrel is lifted by the electric winch, and then the asphalt barrel is placed on the guide rail by horizontal movement. Then the propeller pushes the barrel into the upper chamber through two guide rails, and an empty barrel is pushed out at the rear end outlet.
An anti-drip oil tank is provided at the entrance of the asphalt barrel. The asphalt enters the lower chamber of the box and is continuously heated to a temperature of about 100 to be transported, and then pumped into the asphalt tank by the asphalt pump. The lower chamber can also be used as an asphalt heating tank.
The asphalt decanter plant has the characteristics of not being restricted by the construction environment, strong adaptability and extremely low failure rate. If large production is required, multiple units can be assembled.

In the cold winter, you need to pay attention to the following points when using asphalt melting equipment:
1. Protection from cold and warmth: The equipment needs to be operated indoors or in a place with shading facilities, and ensure that the temperature of the equipment and the surrounding environment is maintained within an appropriate range.
2. Check the equipment: Before use, the equipment should be checked, including whether the circuits, fluid circuits and other parts of the equipment are working normally, and whether there are any leaks of electricity or water in the equipment.
3. Pay attention to safety: During operation, you should wear protective equipment and avoid direct contact with hot asphalt. At the same time, it is necessary to avoid equipment overload operation and prevent equipment damage and safety accidents.
4. Control speed: Reasonably control the working speed of the equipment according to weather conditions and road conditions to avoid overheating of the equipment, causing asphalt to flow too quickly or burn.
5. Storage conditions: When not in use, place the device in a dry, ventilated place with moderate temperature, and ensure that any residue in the device is completely removed.

According to the configuration, layout and controllability of bitumen melting equipment, bitumen melting plant can be divided into three types: mobile, transportable and portable. What should be paid attention to in the production of bitumen melter equipment of different sizes? Let’s learn about it below!
Bitumen melting plant is to fix the demulsifier mixing equipment, black anti-static tweezers, asphalt pump, automatic control system, etc. on a special support chassis. Because the bitumen melter equipment can directly change the production site, it is suitable for the production of emulsion bitumen in construction sites with decentralized projects, small usage and frequent movement.
The main components of the bitumen melting equipments are installed in one or two 60 standard containers. The bitumen melting plant is loaded and transported separately to complete the relocation of the construction site. With the help of asphalt melting equipments hoisting equipment, it is quickly installed and put into operation. Such bitumen melter plant has large, medium and small different configurations, which can meet different project requirements.

The emulsified bitumen equipment hot-melts the base cold-mix colored bitumen, and then disperses the slightly cold-mixed colored bitumen particles into the aqueous solution containing emulsifier through a machine to form liquid cold-mixed colored bitumen sheets.

Colored asphalt pavement is a kind of special pavement material that mixes colored particles into asphalt and then lays on the pavement

Asphalt mixture mixing equipment is a factory-style complete set of equipment that mixes dry and heated aggregates of different particle sizes, fillers and asphalt according to the designed mix ratio at a specified temperature into a uniform mixture. It is widely used in high-grade highways and urban roads. , airports, docks, parking lots and other engineering construction. It is a key equipment for asphalt pavement construction, and its performance directly affects the quality of asphalt pavement.
Generally, there are two types of asphalt concrete mixing equipment: intermittent type and continuous type. The continuous process flow is simple and the equipment is simplified. As for the intermittent forced mixing equipment, due to the secondary screening of aggregates, various components are measured in batches, and forced stirring and mixing can reliably ensure gradation, and the measurement of powder and asphalt can also achieve very high accuracy; so the mixing equipment The asphalt mixture produced is of high quality and can meet various construction requirements.

Synchronized gravel sealing is a process technology for treating cracks in asphalt pavement, and it is currently a road construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical features are? If you don’t know, just follow the editor of Sinoroader and take a look.

Preventive pavement maintenance is a periodic mandatory maintenance measure, which is taken to restore the pavement surface service function when the pavement structure strength is sufficient and only the surface function is attenuated. New preventive maintenance technologies such as super-viscous fiber-added low-noise micro-surfacing and synchronous gravel seal have been widely used on the main lines of national highways, and the construction effect has been widely praised by customers.
Super-viscous fiber-added low-noise micro-surfacing starts with the gradation of micro-surfacing and the main material modified emulsified asphalt. By reducing the structural depth of the micro-surfacing and changing the distribution state of the coarse and fine materials on the surface of the micro-surfacing, the driving noise is reduced, while ensuring its anti-skid performance, effectively improving its adhesion, waterproofness, durability and crack resistance, and can solve the defects of easy detachment, excessive noise and reflective cracks of ordinary micro-surfacing.