Detailed introduction to modified asphalt tank equipment

Precautions during the production of emulsified bitumen equipment. How much do you know about this information? Let’s learn more about it:
When the emulsified bitumen equipment is in production, the viscosity of the bitumen decreases with the increase of temperature. For every 12℃ increase, its dynamic viscosity decreases by about one time. During production, the base bitumen should be heated to liquid state before emulsification. In addition, in order to adapt to the emulsification capacity of the colloid mill, the base bitumen dynamic viscosity is generally controlled to be about 200cst. The lower the temperature, the higher the viscosity, which increases the burden on the bitumen pump and the colloid mill, making it difficult to emulsify; but on the other hand, in order to prevent the demulsification caused by excessive vaporization and evaporation of water in the finished product during the production of emulsified bitumen, it is impossible to heat the base bitumen temperature too high. Generally, the finished product temperature at the outlet of the colloid mill should be controlled to be less than 85℃.

Preventive pavement maintenance is a periodic mandatory maintenance measure, which is taken to restore the pavement surface service function when the pavement structure strength is sufficient and only the surface function is attenuated. New preventive maintenance technologies such as super-viscous fiber-added low-noise micro-surfacing and synchronous gravel seal have been widely used on the main lines of national highways, and the construction effect has been widely praised by customers.
Super-viscous fiber-added low-noise micro-surfacing starts with the gradation of micro-surfacing and the main material modified emulsified asphalt. By reducing the structural depth of the micro-surfacing and changing the distribution state of the coarse and fine materials on the surface of the micro-surfacing, the driving noise is reduced, while ensuring its anti-skid performance, effectively improving its adhesion, waterproofness, durability and crack resistance, and can solve the defects of easy detachment, excessive noise and reflective cracks of ordinary micro-surfacing.

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.

The difficulty of emulsified bitumen equipment itself, because general bitumen also has different classifications, in the production and processing of emulsified bitumen equipment bitumen concrete, it is necessary to pay attention to whether the common raw materials are the common bitumen and ensure the quality. Check the black antistatic tweezers of emulsified bitumen equipment asphalt concrete machine equipment emulsified bitumen equipment.
If the gap of the black antistatic medical tweezers bitumen concrete micro-powder machine of emulsified bitumen equipment is enlarged after long-term use, then we can adjust it and continue to process it. Emulsified bitumen equipment is a relatively simple difficulty.

Changing the color of asphalt pavement is an important project aimed at improving the beauty of roads, optimizing traffic signs and enhancing urban landscape effects. The following is a detailed introduction to the color change of asphalt pavement:
1. Color change method
Using pavement color change spray:
Spray directly on the original asphalt pavement surface to make the road surface look brand new.
This method is simple and fast to construct, with bright and lasting colors, and will not change the structure of the pavement.

In modern highway maintenance work, how to repair asphalt pavement quickly and effectively has become one of the key issues. As an advanced repair technology, cold patching technology is very popular because of its convenient construction and remarkable effects.
What is the cold patching process?
Cold patching process, as the name suggests, refers to a technical method for repairing asphalt pavement without heating. This process uses a specially proportioned cold-patch asphalt mixture. This material can maintain good fluidity and adhesion even at lower temperatures, thus ensuring the quality of the repair.
Advantages of cold patching process
Fast construction: Cold patching materials can be directly applied to damaged areas without preheating, and are immediately open to traffic, greatly shortening repair time.
All-weather construction: Whether in hot summer or cold winter, cold patching materials can be effectively constructed and are not affected by the weather.
Easy to operate: Thanks to its good working properties, even small damaged areas can be repaired easily.
Environmentally friendly: The construction process reduces environmental pollution and is in line with the concept of green construction.
Application scenarios
The cold patching process is suitable for various types of pavement repair work, especially those places where traffic needs to be restored quickly, such as urban main roads, highway ramps, etc. In addition, the cold patching process is also an ideal choice for remote areas or situations where professional heating equipment is lacking.
In short, the cold patching process has occupied a place in the field of rapid repair of asphalt pavement with its unique advantages and has become an indispensable part of modern highway maintenance.

Road repair Keep the road to maintain the performance of the road, restore the damaged part in time, ensure the safety, comfort and smooth driving, save transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time. With the performance, the damaged part is restored in time to ensure the safety, comfort and smooth driving, saving transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time.

Asphalt melting equipment is one of the indispensable equipment in modern road construction. Its main function is to heat a large amount of cold hard asphalt to a suitable working temperature at the construction site. Advanced asphalt melting equipments can greatly improve construction efficiency, reduce human resources and time costs, and ensure pavement quality at the same time.
First of all, reliable asphalt melter equipment can shorten heating time and work efficiency and avoid wasting energy. Secondly, the equipment is easy to operate and can reduce the incidence of on-site safety accidents. In addition, this equipment has an automatic control and monitoring system that can adjust the working status and parameters at any time to meet different construction needs and environmental conditions.

The emulsified bitumen equipment hot-melts the base cold-mix colored bitumen, and then disperses the slightly cold-mixed colored bitumen particles into the aqueous solution containing emulsifier through a machine to form liquid cold-mixed colored bitumen sheets.

1. Observation: Pay attention to the dynamics of the road surface after milling (three to four days), and pave the milled and roughened road surface in time when paving conditions are met.
2. On-site mixing: During construction and production, a sealing slurry truck should be used for on-site mixing. Through the metering equipment of the sealing truck and on-site operation by a robot, it is ensured that emulsified asphalt, water, mineral materials, fillers, etc. can be mixed according to a certain proportion. , stir through the mixing box, and the paving thickness is not higher than the roughing depth.

Modified (rubber powder) bitumen equipment, one of the road maintenance equipment. It is a kind of equipment that measures, mixes and develops SBS, rubber powder and asphalt.
Modified (rubber powder) bitumen equipment is a set of wet modification processing technology, which mainly consists of modified material metering and promotion, bitumen rapid heating, asphalt metering, high-intensity mixing tank, mixed material transfer pump, development tank, colloid mill, Control system and other components.

With the rapid development of highway construction and the increase in demand for asphalt, barreled bitumen has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported bitumen used in high-grade highways is in barrel form, which requires an bitumen melter equipment with fast melting speed, clean debarreling, and prevention of asphalt aging.
The upper part of the debarreler of the bitumen melter equipment is hotter, and each barrel is directly heated by the heat transfer oil coil. The barrel wall directly bears the heat radiation of the heating coil. The asphalt is cleanly and sensitively debarreled, and there will be no waste of asphalt hanging barrels. According to the principle of layered heating, four-layer heating technology is adopted, with single inlet and single outlet of heat transfer oil, and high thermal efficiency of heating; at the same time, the waste heat of combustion exhaust gas is used for secondary heating, and power is effectively used; the debarreler body is insulated with high-quality rock wool material. It is suitable for various types of imported and domestic barrels, and the deformation of asphalt barrels will not affect production.

Synchronous gravel sealing technology refers to the use of special synchronous gravel sealing truck equipment to lay and roll prepared gravel, asphalt and other materials to build a single layer of asphalt gravel wearing layer, which is important for highway pavement. protection of. From the perspective of characteristics, it is simple and easy to implement. It has obvious effects on the prevention of highway diseases, problem solving, later maintenance, and improvement of grade protection. It can also well extend the service life of highways.

Asphalt melting equipment is an important road construction tool used to heat asphalt to the appropriate temperature for construction. It can provide reliable solutions and make road construction more convenient. The working principle of this equipment is to heat the asphalt to the appropriate temperature through a heater, and then transport the hot asphalt to the construction site through a conveying system.

According to statistics, among the high-grade highways that have been built and opened to traffic in my country, about 80% are asphalt pavements. However, with the development of time, the influence of various climatic and environmental factors, and the high-intensity driving load, the asphalt pavement will have different degrees of degradation or damage. Pavement maintenance is to take effective technical means to slow down this degradation, so that the pavement can provide good service quality during its service life.

What details should be paid attention to when adding materials to the emulsified bitumen equipment? Speaking of emulsified bitumen equipment, I don’t know how much you know? What should we pay attention to when adding materials?
The black anti-static tweezers grinding wheel of the emulsified bitumen equipment has no heating barrel. Before use, you must first add an appropriate amount of diesel, let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is about 80 to 100 degrees) Open the shut-off valve on the oil pipe and discharge the diesel in the machine. The temperature of the black anti-static tweezers grinding wheel is about 80 to 100 degrees before it can be loaded and put into production. If there is a heating collet, heat the grinding wheel before starting, and then load the materials for production.

The base layer of asphalt pavement is divided into semi-rigid and rigid. Since the base layer and the surface layer are materials of different properties, good bonding and continuity between the two are the key requirements for this type of pavement. In addition, when the asphalt surface layer seeps water, most of the water will be concentrated at the joint between the surface layer and the base layer, causing damage such as slurry, looseness, and potholes to the asphalt pavement. Therefore, adding a lower seal layer on top of a semi-rigid or rigid base layer will play a vital role in enhancing the strength, stability and waterproofing capabilities of the pavement structural layer. The more commonly used one is to use asphalt gravel synchronous sealing technology.
So let’s take a look at how the construction of the asphalt gravel synchronous sealing truck is carried out:

With the development of science and technology, the emergence of emulsified asphalt tanks has brought great convenience to our work, and is widely used in every site. So what issues need to be paid attention to when filling emulsified asphalt tanks? Below, the editor will introduce to you the relevant knowledge structure diagram, hoping to be of some help to you.

The heating principle of asphalt decanter equipment is to heat, melt and decanter the asphalt through the heating plate. It is mainly composed of de-barreling box, lifting system, propeller and electrical control system.
The box of asphalt decanter plant is divided into upper and lower chambers. The upper chamber is the asphalt melting chamber, which is densely covered with heat transfer oil heating coils or hot air heating pipes. The asphalt is melted and removed from the barrel by heat. The hoisting hook is installed on the gantry, and a barrel grabber is hung. The asphalt barrel is lifted by the electric winch, and then the asphalt barrel is placed on the guide rail by horizontal movement. Then the propeller pushes the barrel into the upper chamber through two guide rails, and an empty barrel is pushed out at the rear end outlet.
An anti-drip oil tank is provided at the entrance of the asphalt barrel. The asphalt enters the lower chamber of the box and is continuously heated to a temperature of about 100 to be transported, and then pumped into the asphalt tank by the asphalt pump. The lower chamber can also be used as an asphalt heating tank.
The asphalt decanter plant has the characteristics of not being restricted by the construction environment, strong adaptability and extremely low failure rate. If large production is required, multiple units can be assembled.

We need to prepare a lot of work when using modified asphalt equipment. What kind of work do we need to prepare? Next, let me briefly introduce the relevant knowledge points.
1. Heat transfer oil heats and insulates the modified asphalt equipment and nozzle. After spraying, the asphalt pump and nozzle do not need to be cleaned with diesel. Use high-pressure air to press the asphalt in the pipeline and spray pipe back to the tank, and then blow the nozzle; use heat transfer oil to keep warm, so that the pipeline and nozzle are smooth and unobstructed. 2. Various asphalts can be spread: high-viscosity asphalt, hot asphalt, emulsified asphalt, etc.; the spreading width can be freely adjusted, each nozzle can be controlled separately, and the maximum spraying width is up to 6m. Flexible handheld spray guns can be used to spray asphalt on corners. 3. Excellent thermal insulation performance, average cooling ≤1-2℃/h. 4. Convenient loading and unloading function. In addition to filling asphalt from the asphalt tank port, hot asphalt can be sucked out by itself, and external asphalt can also be pumped and transferred. 5. The modified asphalt equipment is evenly spread, and the nozzle design can be used for triple overlapping spraying.
The above are the relevant knowledge points of modified asphalt equipment. I hope the above content can be helpful to everyone. Thank you for your viewing and support. More information will be sorted out for you later. Please pay attention to our website updates.

There are many ways to heat bitumen, including using fire source heating, electric heating, steam heating, hot water heating and indirect heating. Fire source heating generates heat by burning fuel to heat the bitumen to a molten state. Electric heating converts electrical energy into thermal energy through electric heating elements to heat the bitumen to a molten state. Steam heating transfers heat to bitumen through steam, heating the bitumen to a molten state. Hot water heating transfers heat to the bitumen through hot water, heating the bitumen to a molten state. Indirect heating transfers heat to the heating medium, which then transfers the heat to the bitumen to heat the bitumen to a molten state.

The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) Open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

In the cold winter, the following points should be noted when using bitumen melter equipment:

1. Keep warm: The bitumen melter equipment needs to be operated indoors or in a place with sunshade facilities, and ensure that the temperature of the bitumen melter and the surrounding environment is kept within an appropriate range.
2. Check the bitumen melting equipment: Before use, the bitumen melter should be checked, including whether the circuit, liquid circuit and other parts of the equipment are working properly, and whether the equipment has leakage, water leakage and other conditions.
3. Pay attention to safety: During operation, protective bitumen melter equipment should be worn to avoid direct contact with hot bitumen. At the same time, avoid overloading the bitumen melter to prevent equipment damage and safety accidents.
4. Control speed: Reasonably control the working speed of the bitumen melting equipment according to weather conditions and road conditions to avoid overheating of the equipment, which may cause the bitumen to flow too quickly or burn.
5. Storage conditions: When not in use, place the equipment in a dry, ventilated and moderately warm place, and ensure that the residue in the equipment is completely cleaned.

The asphalt spreading truck is an intelligent high-tech product that specializes in spreading emulsified asphalt, diluted asphalt, hot asphalt, heavy traffic asphalt and modified asphalt. It is used in highway construction and highway maintenance projects, and can be used for the construction of upper and lower seals, permeable layers, waterproof layers, bonding layers, asphalt surface treatment, asphalt penetration pavements, fog seals and other projects of different grades of highway pavements. , can also be used for the transportation of liquid asphalt or other heavy oil. So what are the advantages of Qiangguomeng’s asphalt spreader trucks?

There is a wide variety of asphalt melting equipment on the market, including different brands and models. The prices of these devices vary widely, depending mainly on factors such as their features, performance, and specifications.
Asphalt melter equipment produced by some large brands such as Sinoroader usually has higher quality and reliability, so the price is relatively higher. However, they also offer longer service life and better maintenance support.

Asphalt mixture is a kind of composite material, mainly composed of asphalt, coarse aggregate, fine aggregate, mineral powder, some also added polymer and wood cellulose; By these different quality and quantity of materials mixed to form different structures, and have different mechanical properties

Based on the characteristics of the high-speed hot mixed bitumen melting equipment, the direct heating bitumen melter equipment tank is a researched, environmentally friendly and energy-saving thermal mixed bitumen melting equipment, which can directly coordinate the temperature of the direct heating bitumen melter heating tank and protect the direct heating asphalt melter equipment. Barrel heating tank. The temperature of hot mixed asphalt barrels achieves the appropriate storage temperature.
When the water level in the drum is lower than the temperature of the thermometer, please close the suction valve before the drum pump is shut down to prevent the drum from flowing back in the heater. After the motor has been running for 2 days, the three-way valve opens quickly.

Everyone must be familiar with slurry sealing and micro-surfacing. But do you know their 7 construction steps?
Slurry sealing and micro-surfacing were both early preventative highway protection technologies. Its function is to ensure the smooth use and extended life of the highway. The construction steps are as follows:

Emulsified asphalt can be spread by mechanical spreading and manual spreading. Different spreading methods will have different effects on pavement performance, so it is very important to choose the right spreading method. At the same time, maintenance and management after spreading are equally important to ensure the safety and durability of the pavement.
Emulsified asphalt is a common pavement material that is widely used in road construction and maintenance. There are two main ways to spread emulsified asphalt: mechanical spreading and manual spreading. Mechanical spreading generally uses a special spreading vehicle that can quickly and evenly spread emulsified asphalt. Manual spreading is carried out by workers using tools such as brushes or rollers, which is suitable for pavement treatment in small areas or special areas.
Different spreading methods also have different effects on pavement performance. Mechanical spreading can quickly complete large-area treatment and spread evenly, which is conducive to ensuring the flatness and anti-skid properties of the pavement. Manual spreading can more finely treat special areas such as shoulders and intersections to improve the overall performance of the pavement.

All kinds of base layers have the problem of strength formation and growth (Emerson). The strength is gradually generated during the curing process, and the internal structure will become more and more dense. The test shows that when the semi-rigid base layer is sprayed with penetration oil before the cement (material: powdered water-hardening inorganic cementitious material) has not yet hardened, the penetration depth is deep; with the increase of age and strength, the penetration effect of the penetration oil is getting worse and worse.
At the same time, timely spreading of penetration oil has a good retention effect on the moisture in the base layer, preventing the evaporation of moisture, ensuring the formation of the strength of the base layer, and the surface of the base layer is not easy to loosen. The penetration oil also protects the semi-rigid base layer from cracking due to exposure to the sun. Furthermore, since the base layer is no longer covered and watered for curing, the temperature inside the base layer is high, which is conducive to the growth of strength.