Dust removal system of asphalt mixing plant

Certain failures cannot be avoided during the use of the asphalt mixing plant. For example, a malfunction of the cold material feeding device may cause the asphalt mixing plant to shut down. This may be due to a malfunction in the asphalt mixing plant or due to gravel or foreign matter being trapped under the cold material belt. If it is stuck, if it is a circuit failure, first check whether the motor control inverter of the asphalt mixing station is faulty and whether the line is connected or open.

Asphalt mixing plants bring a lot of convenience. You should understand what asphalt is. Asphalt is a very viscous liquid with a black surface that dissolves carbon disulfide. They generally exist as asphalt and smoke tar. Asphalt appeared early in social life.

Asphalt mixing stations play an important role in road construction. This article starts from the site selection, commissioning, and acceptance of the asphalt mixing plant, and elaborates on comprehensive and reasonable planning to avoid disturbing the normal construction order.

CONTROL SYSTEM of asphalt plant

1: The site should be located on higher ground and away from residential areas and densely populated areas.
Because part of the equipment of the mixing station is installed below the ground, in order to avoid continuous rainfall. The equipment will suffer disaster, and the changing aggregate moisture content will affect the concrete quality. Quality accidents are prone to occur. Therefore, during site construction, attention should be paid to the construction of drainage pipelines and sand and gravel quarries. With the rapid development of cities. With the continuous expansion of urban scale, environmental protection requirements will become more and more stringent. Urban roads prohibit gravel vehicles from passing, so concrete mixing plants should be built far away from urban areas.

In fact, asphalt mixing stations are not uncommon in our daily lives. They are mainly a unit of equipment specially designed to mix asphalt. What we really don’t understand is the gas system of the asphalt mixing station. Only correct maintenance And operation can bring out the best production effect. So what are the faults in the gas circuit of asphalt mixing station?
The following three points are the more common gas path failures of asphalt mixing stations:

The quality of the asphalt mixing plant will be a key factor affecting the quality of the project. After reviewing relevant materials related to the production and construction of asphalt concrete, we summarized some cases of failures in asphalt concrete mixing stations during construction and analyzed the reasons.
1. Unstable output and low production efficiency of asphalt mixing plants
(1) Improper proportioning. The mix ratio of asphalt concrete is divided into target mix ratio and production mix ratio. Among them, the target mix ratio controls the cold material transportation ratio of sand and gravel materials, and the production mix ratio is the mixing ratio of various types of sand and stone materials in the finished asphalt concrete materials specified in the design. The production mix ratio is determined by the laboratory, which directly determines the off-site grading standard of the finished asphalt concrete. The target mix ratio is set to further ensure the production mix ratio, and can be adjusted appropriately during production according to the actual situation. When the target mix ratio or the production mix ratio is not appropriate, the stones stored in each measurement of the asphalt mixing station will be disproportionate, with some overflowing and some other materials, unable to be weighed in time, and the mixing cylinder will be idling, resulting in reduced output.

When inspecting the asphalt mixing plant, it was found that the asphalt in the pipeline solidified because the temperature of the asphalt transportation pipeline did not meet the requirements. Analysis believes that the reasons for this result are that the high-level oil tank of the heat transfer oil is too low, resulting in poor circulation of the heat transfer oil; the second is that the inner tube of the double-layer pipe is eccentric; the third is that the heat transfer oil pipeline is too long; and the fourth is that the heat transfer oil pipeline is not insulated measure.

In today’s road construction, the use of a large number of road construction machinery represents the entry into the era of highway mechanization. For users, the goal is to use road construction machinery reasonably and tap its potential as much as possible. However, road construction machinery requires various accessories to work together. Now let’s take the asphalt mixing plant as an example to see what commonly used accessories and equipment are available.
Asphalt mixing plant equipment is a relatively complex system, which includes many equipment, mainly nine parts, namely: bag dust removal, finished material temporary storage warehouse, grading machine, fast heating asphalt tank, asphalt barrel removal machine, asphalt recycled material crushing and screening system, coal block crusher, coal mill and dust removal equipment, etc.

Asphalt mixing stations and equipment must implement secondary leakage protection measures. They can only be used after being plugged in and operated through the circuit breaker before use. During the trial operation, it is necessary to verify that the rotational speed of the mixing drum will be inappropriate.

Road construction machinery is a large range, so let’s talk about one of it, which is the asphalt mixing plant. It is mainly used to produce asphalt, so it is very important among road construction machinery and equipment. An important part, if the quality of the finished product is not good, it will greatly affect the quality of the road. Therefore, below, the editor will use the form of question and answer to guide you to continue learning.

The mixing speed of asphalt mixing plant equipment is indeed very fast, and the corresponding mixing power must be very high, but the specific amount must be measured in a certain way to determine the scope of use of asphalt mixing equipment. There are many methods to measure the mixing power of asphalt mixing equipment, but the relatively small errors are the motor counter-torque measurement method and the strain measurement method.
When the motor of the asphalt mixing equipment starts running, the electromagnetic moment acting on the motor rotor and the electromagnetic moment acting on the motor stator are equal, but their directions are opposite. Therefore, as long as the torque acting on the stator is measured, the torque on the rotor can be obtained, and the actual mixing torque is obtained after deducting the friction torque on the rotor bearing.
On the premise of knowing the torque and mixing speed, the mixing power of the asphalt mixing equipment can be calculated. This is the so-called motor counter-torque measurement method, which is relatively simple and suitable for smaller mixing systems.

Asphalt mixing plant, also known as asphalt concrete mixing plant, is a complete set of equipment for batch production of asphalt concrete. Its efficient and stable operation is of great significance to ensure the quality of the project. It is mainly used in the construction of highways, grade roads, municipal roads, airports, ports and other projects. According to the mixing method, asphalt mixing plant can be divided into forced intermittent type and continuous production type; according to the transportation method, it can be divided into fixed type, semi-fixed type and mobile type.
The working principle of asphalt mixing plant mainly includes steps such as aggregate processing, asphalt processing and mixture mixing. Specifically, aggregates (such as gravel, crushed stone, etc.) are sent to aggregate bins through conveyors or bucket elevators, and then measured by aggregate metering devices, and a certain amount of aggregates are sent to sub-bins. Asphalt is stored in asphalt bins or oil storage tanks, and is measured by asphalt metering devices, and a certain amount of asphalt is sent to asphalt sub-bins. Finally, according to the ratio requirements, different aggregates are taken out from their respective sub-bins and sent to the mixture mixer through conveyors or bucket elevators for mixing.

Asphalt mixing plant, also known as asphalt concrete mixing plant, asphalt mixing equipment. Refers to a complete set of equipment used for mass production of asphalt concrete. According to the mixing method, it can be divided into intermittent type and continuous type; according to the transportation method, it can be divided into fixed type, semi-fixed type and mobile type.

Judging from the situation of highways in our country, asphalt pavement is the most used, which is one of the reasons why asphalt mixing plants have developed so rapidly. Under the situation of rapid economic development, the quality problems of asphalt pavement are gradually increasing, which puts forward higher and higher requirements for the quality of asphalt. It is understood that the primary factor that affects the quality of asphalt is the ratio of raw materials. This is also covered in the introduction of asphalt mixing stations. You can discuss it together.
In order to obtain high-quality asphalt products, in addition to the asphalt mixing equipment meeting the requirements, selecting the appropriate asphalt mixture gradation type is also a top priority. According to my country’s current regulations, the maximum particle size of the asphalt mixture in the upper layer of the highway should not exceed half of the layer thickness; while the maximum particle size of the aggregate in the middle surface layer of asphalt mixture should not exceed two-thirds of the layer thickness; and the asphalt layer should not exceed half of the layer thickness. The maximum nominal aggregate size of the pavement structural layer mixture should not exceed one-third of the layer thickness.
Based on this analysis, if an asphalt surface layer with a certain thickness is selected according to the above specifications, the particle size of the asphalt mixture aggregates will generally be larger, which will inevitably bring insurmountable construction difficulties to the construction of asphalt concrete pavement. After investigation, testing, analysis, and comparison, it can be seen that the lower layer has a wider choice, so the AG-201 gradation type can be used; while the selection of the upper layer mixture type is more difficult, and it is necessary to achieve a reasonable choice of this mix ratio. , on the one hand, we must examine as many aggregate resources as possible, and on the other hand, we must also consider the model of the mixing equipment.
In order to ensure the quality of the project, strict selection and inspection of engineering materials must be carried out. Therefore, the selection and determination of raw materials should be based on the requirements for pavement structure and use quality, combined with the supply of floor materials, and inspection in accordance with the requirements of relevant test procedures, and then Select the best materials so that all technical indicators of the materials meet the specified technical requirements.

The asphalt mixing plant contains multiple different systems with different functions. The drying system is one of them. Its main function is to heat and dry the materials to reach the temperature required for the process. In order to successfully achieve this goal, the drying system must provide a certain amount of heat.

Asphalt mixing equipment is equipment used to produce asphalt concrete in large quantities. Because this equipment is affected by various factors during the production process, some problems will inevitably occur after a period of use. Sinoroader Group The editor of the asphalt mixing equipment company of China Machinery Co., Ltd. will introduce to you the methods of rescuing damaged parts in asphalt mixing equipment.
Asphalt mixing equipment encounters different problems, and the solutions are also different. For example, one of the common problems of asphalt mixing equipment is that parts are worn out and damaged. The solution that needs to be done at this time is to start from the production of parts. Just start improving.

In my country, most of the raw materials used in highway construction are asphalt, so asphalt mixing plants have also developed rapidly. However, under the situation of rapid economic development in my country, the problems of asphalt pavement have gradually increased, so the market requirements for asphalt quality have become higher and higher.
There are many factors that affect the quality of asphalt. In addition to the need for asphalt mixing plant equipment to meet conventional requirements, the ratio of raw materials is also very important. At present, my country’s existing industry specifications indicate that the maximum particle size of the asphalt mixture used on the upper layer of the highway cannot exceed half of the thickness, and the maximum particle size of the aggregate of the middle asphalt mixture cannot exceed two-thirds of the thickness of the layer, and the maximum size of the structural layer cannot exceed one-third of the same layer.

Oscillating screen. It can screen the heated aggregate according to the design. It requires fully enclosed, double oscillating motor replacement (replacing one substance for another (mostly the strong one takes the place of the weak)) eccentric shaft oscillation, each The layer screen is easy to install quickly. The service life of the drying roller and the power part is not less than 6000h. The roller can fully use heat, the material curtain flows evenly, and the inclination is required to be adjustable.

In order to keep the asphalt mixing plant in a stable operating process, a series of adverse factors related to it must be excluded. What should be paid attention to in this process?
First of all, the selection of the delivery pump in the asphalt mixing plant must meet the requirements of asphalt pouring per unit time during construction, height, and horizontal distance requirements. At the same time, there must be a certain technical and production capacity reserve, and the balanced production capacity is preferably 1.2 to 1.5 times.
Secondly, the movement and hydraulic systems of the asphalt mixing plant must be normal, and there must be no abnormal sound and vibration to avoid large aggregates and lumps inside the equipment, otherwise it is easy to get stuck at the feed inlet of the mixing plant or be blocked due to arching. Another point is that when the asphalt mixing plant is in the same site, it is not suitable to use too many pumps and pumps from multiple manufacturers to avoid affecting its normal operation.

In the 21st century, with the booming development of modern engineering construction, complex integrated supporting equipment has been invested in large quantities. Its complex process and more independent operating components have relatively high requirements for the performance of its equipment control system. The application of PLC in asphalt mixing station realizes the control of the entire process of asphalt mixing station, which facilitates the construction of modern engineering construction. Therefore, this article discusses and analyzes the application of PLC in asphalt mixing station, which has certain economic value and practical significance.

Asphalt mixing station is the standard for mixing asphalt. Having said that, many people still think that this has nothing to do with us. We don’t use asphalt, but do you know that our roads are made of asphalt? When I was a child, I used asphalt to pluck pig hair. The hair on the pig’s head was indeed clean. When using asphalt, it must be burned hot, because if it is cold, it will be very hard and cannot be used. Therefore, if a large amount of asphalt is needed, there must be an asphalt mixer because there is no more convenient equipment than it.
What kind of source material is asphalt that requires special equipment. Asphalt is a black-brown, high-viscosity organic liquid composed of hydrocarbons and non-metallic substances of different molecular weights. The surface is black and soluble in carbon disulfide. At the same time, it is also a waterproof, moisture-proof and anti-corrosion organic gelling material. It can be mainly divided into three types: coal tar asphalt, petroleum asphalt and natural asphalt. Asphalt is mainly used in industries such as coatings, plastics, rubber, and paving roads.

Asphalt mixing stations are constructed according to a certain process, which can not only ensure the construction quality, but also ensure that the asphalt mixing station is not damaged. Although construction details are critical, the key skills of asphalt mixing station construction must be mastered.
Before the construction of the asphalt mixing plant, the top surface of the asphalt mixing station construction range should be removed, and the site elevation should be kept dry and flat to meet the design requirements. If the surface is too soft, the foundation should be reinforced to prevent the construction machinery from losing stability and ensure that the pile frame is vertical.
Then the on-site construction machinery should be inspected to ensure that the machinery is intact and assembled and tested under the premise of meeting the requirements. To ensure the verticality of the asphalt mixing plant, the deviation of the gantry guide and the mixing shaft from the verticality of the ground shall not exceed 1.0%. Asphalt mixer manufacturer.

In general, the development of my country’s asphalt mixing plant industry is very rapid. In the ton segment, it quickly occupied most of the market share. And with the advancement of technology, it can basically meet the current development needs. However, the total demand for some large-scale asphalt mixing plants has not increased or decreased. What are the reasons?
If we analyze from multiple angles, it is not difficult to find that these reasons are also some of the problems faced by my country’s current asphalt mixing plantindustry. These problems are summarized as follows:

Asphalt mixing stations, also known as asphalt concrete mixing stations, can produce asphalt mixtures, modified asphalt mixtures, and colored asphalt mixtures, which fully meet the needs of building highways, grade roads, municipal roads, airports, ports, etc. Changmeng Electric Power introduces the safety operating procedures of asphalt mixing plants below:
1. During the operation of the mixing equipment, in addition to ensuring that the equipment is in good condition, it should also be equipped with a mineral moisture content detector and a finished material tester, and the relevant data should be frequently tested for the operator to adjust the operation in time to keep the equipment in good condition.
2. In addition to affecting production capacity, the moisture content of mineral materials is also the main factor determining fuel consumption. Additional material sheds should be added.
3. Before operation, all working parts and devices of the mixing equipment should be fully checked to see if they are intact and normal. If there are any problems, they must be properly handled before operation, and it is forbidden to operate with illness.
4. The operation must be carried out strictly in accordance with the procedures and precautions specified in the instruction manual. After normal ignition, the dust collector should be monitored to ensure that the drying drum burns under negative pressure; after production starts, the hot material elevator and agitator should be monitored to see if they are working normally to coordinate the operation of other parts.

asphalt mixture mixer

Judging from the current situation of domestic highway construction, asphalt mixing stations will also achieve great development for a long time to come. This is also a result of rapid economic development. However, we have found that more and more quality problems occur when constructing asphalt pavements in modern times. Therefore, we have to put forward more stringent requirements for the quality of asphalt.

There is also a reversing valve in the asphalt mixer, which generally does not cause problems, so I have not understood its solution in detail before. But in actual use, we encountered this kind of failure. How should we deal with it?