Economic performance of emulsion bitumen equipments

The main filter material of stainless steel barrel removal adopts five-layer sintered mesh. Standard five-layer calcination is made by stacking and vacuum calcining five layers of stainless steel barrel removal wire mesh. The stainless steel barrel made of it has corrosion resistance, good water permeability, high compressive strength, easy cleaning and back-cleaning, high filtration precision, hygienic and clean filter material, and stainless steel barrel removal wire mesh does not fall off.
Double-layer metal sintered mesh is a new type of filtration system with high impact toughness and overall rigidity, which is made by stacking and vacuum calcining double-layer stainless steel barrel removal wire mesh products.

Asphalt spreader vehicle is an intelligent and automated high-tech product that specializes in spreading emulsified asphalt, diluted asphalt, hot asphalt, high-viscosity modified asphalt, etc.
Asphalt spreader is used for spreading the penetration oil, waterproof layer, and bonding layer of the bottom layer of the asphalt pavement of high-grade highways. The spreader consists of a car chassis, an asphalt tank, an asphalt pumping and spraying system, a thermal oil heating system, a hydraulic system, an ignition system, a control system, a pneumatic system, and an operating platform.
Asphalt spreader is cumbersome to operate. On the basis of absorbing various technologies of similar products at home and abroad, it increases the quality technology content of construction and the humanized design of outstanding improvement of construction conditions and construction environment. Its reasonable and reliable design ensures the uniformity of asphalt spreading, the computer control is stable and reliable, and the technical performance of the whole vehicle has reached an advanced level.

The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) Open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreading truck, check the four heat transfer oil valves and air pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Try running the asphalt pump and cycle for 5 minutes. If the pump head shell is hot to your hands, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not rotate or make noise. You need to open the valve and continue to heat the asphalt pump until it can operate normally.

Everyone must be familiar with slurry sealing and micro-surfacing. But do you know their 7 construction steps?
Slurry sealing and micro-surfacing were both early preventative highway protection technologies. Its function is to ensure the smooth use and extended life of the highway. The construction steps are as follows:

All kinds of base layers have the problem of strength formation and growth (Emerson). The strength is gradually generated during the curing process, and the internal structure will become more and more dense. The test shows that when the semi-rigid base layer is sprayed with penetration oil before the cement (material: powdered water-hardening inorganic cementitious material) has not yet hardened, the penetration depth is deep; with the increase of age and strength, the penetration effect of the penetration oil is getting worse and worse.
At the same time, timely spreading of penetration oil has a good retention effect on the moisture in the base layer, preventing the evaporation of moisture, ensuring the formation of the strength of the base layer, and the surface of the base layer is not easy to loosen. The penetration oil also protects the semi-rigid base layer from cracking due to exposure to the sun. Furthermore, since the base layer is no longer covered and watered for curing, the temperature inside the base layer is high, which is conducive to the growth of strength.

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

The modified asphalt equipment estimates the quality and uniformity of various raw materials from the material pile and conveyor at any time. The modified asphalt equipment checks the soil and oversized gravel, and checks whether there is any leakage in the cold hopper. Estimate whether the mixed material is mixed evenly, whether there is white material, whether the oil-stone ratio is reasonable, and check the concrete segregation of the asphalt mixture and the mixed material.
The modified asphalt equipment checks the control parameters of various basic parameters of the mixing device in the control room, the display values ??of the control screen, and the modified asphalt equipment checks whether the data statistics and display values ??of the computer and printout are consistent. Test the raw material heating temperature and the mixed material entry temperature of the modified asphalt equipment.

Colored asphalt pavement is a kind of special pavement material that mixes colored particles into asphalt and then lays on the pavement

The bitumen decanter equipment is mainly composed of barrel removal shell (BOX), hoisting mechanism, hydraulic booster and electrical control system. The shell is divided into two chambers, the left and right chambers. The upper chamber is a chamber for melting a large barrel of bitumen (definition: the transformation process of a substance from solid to liquid). There are heating coils evenly distributed around it.

What is an bitumen colloid mill used for? Everyone knows about colloid mill, but what about bitumen colloid mill?
Bitumen colloid mill is a high-tech multifunctional crushing and grinding equipment. The motor drives the rotating teeth and fixed teeth to rotate at high speed, generating a sharp speed gradient, which causes the boring to be strongly sheared, rubbed and turbulent, and finally achieves emulsification and dispersion. and homogenizing effect equipment.

The emulsified bitumen equipment hot-melts the base cold-mix colored bitumen, and then disperses the slightly cold-mixed colored bitumen particles into the aqueous solution containing emulsifier through a machine to form liquid cold-mixed colored bitumen sheets.

Water is one of the raw materials of the modified asphalt storage tank, and it is distributed in various components of the modified asphalt storage tank equipment. According to the components where water is distributed, the anti-cold measures are explained one by one. The water tank of the modified asphalt storage tank, the water inside the water tank is released through the filter valve. Some instruments of the modified asphalt storage tank do not have a filter valve to save the cost of the equipment. The modified asphalt storage tank can only be drained by loosening the flange bolts at the bottom. The water pump of the modified asphalt storage tank mentioned here includes a hot water pump and a circulating water pump. This type of water pump for the modified asphalt storage tank generally uses a pipeline centrifugal pump. There is a sewage outlet at the bottom of the pipeline centrifugal pump. The modified asphalt storage tank pays attention to the sewage treatment of the sewage outlet at the bottom of the pump. The modified asphalt storage tank emulsion tank generally uses a cone bottom. However, in order to better process the modified asphalt storage tank coefficient, the inlet and outlet are usually not placed at the bottom of the modified asphalt storage tank. Emulsion (mostly water) will remain at the bottom of the tank, and this part of the residual liquid in the modified asphalt storage tank must be discharged through the filter valve at the bottom. Emulsion pump for modified asphalt storage tank There are basically two types of emulsion pumps for modified asphalt storage tank equipment on the market, gear pumps or centrifugal water pumps. Gear pumps can only discharge the liquid inside the pump through the connection flange of the pipeline. The centrifugal water pump for modified asphalt storage tanks uses its own sewage outlet for sewage treatment. The first four items of modified asphalt storage tanks with basic knowledge are basically discharged, and the modified asphalt storage tanks will focus on the latter types. Modified asphalt storage tank colloid mill There will also be residual emulsion or water inside the modified asphalt storage tank colloid mill. The gap between the stator and rotor of the colloid mill is within 1mm. If there is a little residual water in the modified asphalt storage tank, it will cause the accident of frozen modified asphalt storage tank. The residue in the colloid mill can be treated by loosening the connection bolts of the finished product pipeline.

In addition to being used according to regulations, modified bitumen equipment should also be maintained regularly in order to effectively extend the service life of modified bitumen equipment. The delivery pump of modified bitumen equipment, as well as its motor and reducer, need to be maintained in accordance with the specifications of the instructions. If the modified bitumen equipment is parked for a long time, the liquid in the tank and pipeline needs to be drained, and each moving component also needs to be filled with grease. The dust in the control box of the modified bitumen equipment needs to be cleaned once every six months. A dust blower can be used to remove dust to prevent dust from entering the machine and damaging parts. The micro powder machine needs to add unsalted butter once for every 100 tons of emulsified bitumen produced.

After the rubber bitumen storage tank is cleaned, the wood chips are sent to the rubber bitumen storage tank, and the wood chips and the bottom of the rubber bitumen storage tank are wiped with wood chips. The dirt and wood chips in the bitumen tank can be weathered naturally. The rubber bitumen storage tank is not allowed to be damaged. Check the technical specifications of the underwater concrete processing equipment and ventilation equipment.
The bottom of the rubber bitumen storage tank drain pipe is discharged from the drainage pipe, and the waste water is discharged into the empty tank or other containers through the inlet and outlet and the self-draining pipe. Open the Shenzhen manhole into the plastic suction pipe and pave the Shenzhen manhole with asbestos to reduce the discharge of oil and gas. When manually pumping the bottom oil, two people should be operated to improve the labor efficiency of the workers and send the fuel tank to supervision.

Changing the color of asphalt pavement is an important project aimed at improving the beauty of roads, optimizing traffic signs and enhancing urban landscape effects. The following is a detailed introduction to the color change of asphalt pavement:
1. Color change method
Using pavement color change spray:
Spray directly on the original asphalt pavement surface to make the road surface look brand new.
This method is simple and fast to construct, with bright and lasting colors, and will not change the structure of the pavement.

According to statistics, among the high-grade highways that have been built and opened to traffic in my country, about 80% are asphalt pavements. However, with the development of time, the influence of various climatic and environmental factors, and the high-intensity driving load, the asphalt pavement will have different degrees of degradation or damage. Pavement maintenance is to take effective technical means to slow down this degradation, so that the pavement can provide good service quality during its service life.

● The spreading amount is accurate, and three overlapping asphalt sprayings can be achieved with good uniformity;
● Intelligent control of spreading amount, real-time monitoring of spreading amount and vehicle speed, closed-loop control;
● Full computer touch screen operation, equipped with video monitoring system, the entire work process can be observed at any time;
● Reliable performance, durability and easy operation;

Precautions for checking emulsified asphalt equipment
Sinoroader emulsified asphalt pavement engineering common equipment, now has gradually been widely used.
We all know that before any equipment is used, the equipment should be preliminarily inspected to check whether the installation is normal, and then put into use. The use of modified asphalt modified asphalt production equipment can also extend the peak season. The modified asphalt and stone water machine can be mixed with wet stone to form a continuous film under the surface conditions of low-temperature asphalt and stone. The viscosity of the asphalt is low and the viscosity of the emulsified asphalt is low. Wet film below 10 degrees.

Synchronous sealing trucks play an important role in road maintenance. Daily maintenance of synchronous sealing trucks is an important part of ensuring the good operation of the equipment and extending its service life. Here are some common maintenance measures:

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

How to reduce the energy consumption of emulsified asphalt production equipment is a concern of many users, and is also an issue that many manufacturers attach great importance to. Therefore, today Sinoroader, as a manufacturer of emulsified asphalt production equipment, would like to take this opportunity to share with you how to reduce the production of emulsified asphalt. Equipment energy consumption method.
Since emulsified asphalt appears as a finished product in emulsified asphalt production equipment, and the outlet temperature of ordinary emulsified asphalt is about 85°C, the outlet temperature of emulsified modified asphalt is above 95°C, so there is a lot of latent heat in emulsified asphalt, but emulsified asphalt The production equipment does not make good use of them, but directly enters the finished product tank, allowing the heat to be lost at will, resulting in a waste of energy.

The selection of asphalt melting equipment should take into account factors such as the use environment, working conditions, and technical requirements. Common ones include hot oil heating equipment, electric heating equipment, and gas heating equipment.
Hot oil heating equipment is suitable for occasions that require long-term heating and high temperature control accuracy;
Electric heating equipment is suitable for small projects or occasions where temperature control accuracy is not required;
Gas heating equipment has the advantages of simple operation and low cost, but safety protection measures must be strictly followed.
When choosing, it is also necessary to comprehensively consider factors such as economy and environmental protection.

What key points should be paid attention to when feeding emulsified asphalt equipment? When it comes to emulsified asphalt equipment, I don’t know how much you know about it? What should you pay attention to when adding materials?
The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

Asphalt used to pave roads. It can be obtained by regular vacuum distillation of crude oil with appropriate properties, and can also be obtained by shallow oxidation of vacuum residue or propane deasphalting process. It can also be prepared by mixing asphalt of different duction and injection degree

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.
For the block asphalt melting equipment, the Provincial Environmental Protection Department will review the application materials, and appoint the Provincial Block Asphalt Melting Equipment Management Office to organize relevant doctors to conduct technical evaluation and on-site technical evaluation, and produce expert technical evaluation opinions and on-site inspection reports. Then report the materials of the block asphalt melting equipment to the meeting of directors for scientific research and make a review decision.

Modified bitumen equipment uses modified bitumen colloid mill. Its blade has high hardness, high linear speed of the moving disk, and the gap can be adjusted to 0.15mm. It is suitable for processing various polymer-modified bitumens, such as SBS, PE, EVA, etc.

Fillers used in emulsion bitumen equipment are generally divided into two types: chemically active and non-chemically active. In the production of emulsion bitumen equipment, it can improve the stability of the slurry mixture, speed up or slow down the demulsification speed, and improve the strength of the sealing layer. When adding chemically active fillers, the reaction and compatibility of the fillers with mineral materials and modified emulsion bitumen should be fully considered.

From the current point of view, road construction machinery has bottomed out and asphalt meltering equipment has risen rapidly. In recent years, highway construction and maintenance departments have a strong awareness of using asphalt mixing equipment, especially in developed coastal areas such as Beijing, Shanghai, Jiangsu, Zhejiang, etc. In addition, these regions have a fast economic growth rate, relatively developed industry, and strong comprehensive economic strength. Therefore, the consumption of asphalt mixing equipments in these regions has always been at the forefront of the country. With the rapid development of highway construction and the increase in demand for asphalt, barreled asphalt has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported asphalt used in high-grade highways is in barrel form, which requires an asphalt meltering equipment with fast melting speed, clean de-barreling, and can prevent asphalt aging. my country’s highway construction has achieved remarkable results, among which mechanized production has contributed greatly. Different types of asphalt mixers and bitumen meltering equipment are selected for the characteristics of large highway pavement construction and tight construction period. With the rapid development of my country’s economy, the further extension of expressways, and the large-scale development of western construction, the central and western regions have become new investment hotspots. While paying attention to the market in the developed eastern regions, domestic road construction machinery manufacturers have also increased their efforts to develop the central and western markets, creating new highlights for the domestic asphalt mixing plants consumer market. In summary, my country’s asphalt mixing plant sales market has begun to move westward with the westward movement of investment hotspots. As the market center of gravity gradually shifts westward, the market in the western region is gradually heating up. The self-heating integrated structure, hot air barrel melting and bitumen barrel flipping technology in the asphalt barrel removal equipment are our company’s self-heating integrated structure. The thermal oil furnace used in the old equipment is perfectly integrated with the asphalt barrel removal equipment body, which reduces the volume of the entire set of equipment, greatly reduces equipment investment, saves equipment space and transfer transportation costs.

Bitumen melter equipment plays an important role in highway construction, but traditional heating methods have problems such as high energy consumption and low efficiency. This article introduces a new type of bitumen melting plant, which uses electric heating technology and has the advantages of energy saving, environmental protection and environmental protection. The working principle of this equipment is to heat the bitumen through the heat generated by the resistance wire, and then automatically adjust the temperature and flow rate through the control system to achieve the best melting effect.