Features of mobile asphalt mixing plant:

Safety is the key point for any piece of equipment, and asphalt mixers are of course no exception. What I want to share with you is the knowledge in this area, that is, the safe operation specifications of asphalt mixers. You might as well pay attention to it.

1: The site should be located on higher ground and away from residential areas and densely populated areas.
2: The venue should consider the transportation distance and choose a location with convenient transportation.
3: Determine the website construction plan according to the terrain

There is also a reversing valve in the asphalt mixing plant, which generally does not cause problems, so I have not understood its solutions in detail before. But in actual use, we encountered this kind of failure. How should we deal with it?
The failure of the reversing valve of the asphalt mixing station is not complicated, that is, the reversing is not timely, gas leakage, electromagnetic pilot valve failure, etc. The corresponding causes and solutions are of course different. For the reversing valve to not change direction in time, it is generally caused by poor lubrication, the spring is stuck or damaged, oil dirt or impurities get stuck in the sliding part, etc. For this, it is necessary to check the status of the lubricator and the quality of the lubricating oil. Viscosity, if necessary, the lubricant or other parts can be replaced.
After long-term use, the reversing valve is prone to wear of the valve core sealing ring, damage to the valve stem and valve seat, resulting in gas leakage in the valve. At this time, the sealing ring, valve stem and valve seat should be replaced, or the reversing valve should be replaced directly. In order to reduce the failure rate of asphalt mixers, maintenance must be strengthened on a daily basis.

1: The site should be located on higher ground and away from residential areas and densely populated areas.
Because part of the equipment of the mixing station is installed below the ground, in order to avoid continuous rainfall. The equipment will suffer disaster, and the changing aggregate moisture content will affect the concrete quality. Quality accidents are prone to occur. Therefore, during site construction, attention should be paid to the construction of drainage pipelines and sand and gravel quarries. With the rapid development of cities. With the continuous expansion of urban scale, environmental protection requirements will become more and more stringent. Urban roads prohibit gravel vehicles from passing, so concrete mixing plants should be built far away from urban areas.

1.During the operation of asphalt mixing station equipment, in addition to ensuring that the asphalt mixing station equipment is in good condition, it should also be equipped with a mineral moisture content detector and a finished material tester, and the relevant data should be frequently tested for the operator to adjust the operation in time, so as to keep the equipment in good condition.
2. In addition to affecting production capacity, the moisture content of mineral materials is also the main factor that determines fuel consumption. Additional material sheds should be added.
3. Before operation, all working parts and devices of the asphalt mixing station equipment should be fully checked to see if they are intact and normal. If there is a problem, it must be properly handled before operation, and it is forbidden to operate with illness.

The basic working principle of the green asphalt mixing plants can be roughly summarized in the following ways:
To put it simply, an asphalt plant is actually a set of equipment that can mix several materials according to a predetermined ratio to form a relatively uniform mixture. It is currently widely used and is very important for the construction of different projects. Its performance Various aspects also have a great impact on the engineering quality of asphalt pavement.
Asphalt mixing plant equipment is usually divided into two structures. The intermittent type is relatively more complex in structure and process. The aggregates need to be screened twice and then measured in batches. The batching accuracy is higher. , the mixing quality is good and can meet different construction requirements. The continuous type has a slightly lower accuracy due to its simple structure and simplified operating procedures.

[1]. Composition of intermittent asphalt mixing plant
The intermittent asphalt mixing plant mainly consists of cold material silo, cold material distribution system, cold material conveying system, combustion and drying system, ventilation and dust removal system, hot material elevator, vibrating screen, hot material silo, powder conveying system and asphalt conveying system. System, metering system, mixing cylinder, control system, finished material transportation and storage system, asphalt heating and insulation system, etc.
2. Discussing the phenomenon of warehouse cascading in asphalt concrete mixing plants
2.1 First, let’s introduce the structure and principle of vibrating screen. The main components include: RetentionRubber, SupportTube, vibrating screen drive system and supporting electrical components
The working principle is introduced as follows: hot aggregate is sent to the vibrating screen through the hot aggregate elevator, and the hot aggregate is vibrated and screened by the vibrating screen. Stones of different specifications enter their corresponding hot aggregate bins through the screen and cannot pass through the geotechnical work. The super-sized particles from the cloth screen enter the overflow bin and are sent out.

People pay more and more attention to urban construction, and the use of asphalt is increasing. The application rate of asphalt mixing station is naturally growing rapidly.
Asphalt mixing station will encounter some faults more or less during use. The most common ones are uneven wear of the supporting wheel and wheel rail. Sometimes there will be some abnormal noise and gnawing. The main reason for this is that after the asphalt mixing station has been working for a period of time, the internal drying cylinder will be subjected to high temperature, and then friction will occur between the supporting wheel and wheel rail.
The above situation will also be accompanied by severe shaking, because the asphalt mixing station will directly cause the gap between the wheel rail and the supporting wheel to be improperly adjusted under the action of the drying material, or the mutual position of the two will be skewed. When encountering this situation, the user should add grease to the surface contact position of the supporting wheel and the wheel rail after daily operation.
In addition, the staff also need to pay attention to and timely adjust the tightness of the fixing nut while adding grease, and then effectively adjust the spacing between the supporting wheel and the wheel rail, so that the asphalt mixing station can work smoothly, all contact points can be evenly stressed, and there will be no shaking.

What should I do when the reversing valve in the asphalt mixing plant fails? The editor has a trick:
1. The reversing valve cannot be reversed or the reversing action is slow, which is generally caused by poor lubrication, stuck or damaged springs, oil or impurities stuck in the sliding parts. In this regard, you should first check whether the oil mist is working normally; whether the viscosity of the lubricating oil is appropriate. If necessary, the lubricating oil should be replaced, the sliding part of the reversing valve should be cleaned, or the spring and reversing valve should be replaced.

The drive unit is one of the important components of the asphalt mixing plant, so whether it can be reliably operated must be highly valued to avoid adverse effects on the entire asphalt mixing plant. In order to ensure that the drive unit in the asphalt mixing plant is indeed complete and reliable, the following maintenance measures are essential.
The first thing to pay attention to is the universal rotating part of the drive unit of the asphalt mixing plant. This part has always been a fault-prone part. In order to reduce the occurrence of faults, grease should be added on time, and the wear should be checked frequently, and repaired and replaced in time. Users should also prepare the universal shaft assembly to avoid affecting the working process of the entire asphalt mixer.
Secondly, the cleanliness of the hydraulic oil used in the asphalt mixing plant must be ensured. After all, the working environment of the equipment is relatively harsh, so it is necessary to prevent sewage and mud from entering the hydraulic system. The hydraulic oil should also be replaced regularly according to the requirements of the manual. Once water or mud is found mixed in the hydraulic oil during inspection, the hydraulic system should be stopped immediately to clean the hydraulic system and replace the hydraulic oil.
Since there is a hydraulic system, of course, a matching cooling device is also required, which is also an important focus in the drive system of the asphalt mixing plant. To ensure that its function can be fully exerted, on the one hand, the hydraulic oil radiator should be cleaned regularly to prevent the radiator from being blocked by cement; on the other hand, the radiator electric fan should be checked to see if it is running normally to prevent the hydraulic oil temperature from exceeding the standard.
In general, as long as the hydraulic oil of the asphalt mixing plant drive device is kept clean, there are generally few faults; but the service life varies from manufacturer to manufacturer, so pay attention to its alkalinity observation and replace it in real time.

When inspecting the asphalt mixing plant, it was found that the asphalt in the pipeline solidified because the temperature of the asphalt transportation pipeline did not meet the requirements. Analysis believes that the reasons for this result are that the high-level oil tank of the heat transfer oil is too low, resulting in poor circulation of the heat transfer oil; the second is that the inner tube of the double-layer pipe is eccentric; the third is that the heat transfer oil pipeline is too long; and the fourth is that the heat transfer oil pipeline is not insulated measure.

After use, asphalt mixing equipment needs to be disassembled, cleaned, and maintained before it can be saved for next use. Not only is the disassembly process of the equipment important, but the previous preparation work also has a greater impact, so it cannot be neglected. Please pay attention to the detailed introduction below for specific content.

In general, the development of my country’s asphalt mixing plant industry is very rapid. In the ton segment, it quickly occupied most of the market share. And with the advancement of technology, it can basically meet the current development needs. However, the total demand for some large-scale asphalt mixing plants has not increased or decreased. What are the reasons?
If we analyze from multiple angles, it is not difficult to find that these reasons are also some of the problems faced by my country’s current asphalt mixing plantindustry. These problems are summarized as follows:

Asphalt mixing plant is a very practical engineering machinery. Especially in the road construction process, it plays an irreplaceable role. Due to its importance, in addition to ensuring its own quality, the use and maintenance of the equipment must be carried out normally. Let’s learn about the daily maintenance requirements of asphalt mixing plants.

In the 21st century, with the booming development of modern engineering construction, complex integrated supporting equipment has been invested in large quantities. Its complex process and more independent operating components have relatively high requirements for the performance of its equipment control system. The application of PLC in asphalt mixing station realizes the control of the entire process of asphalt mixing station, which facilitates the construction of modern engineering construction. Therefore, this article discusses and analyzes the application of PLC in asphalt mixing station, which has certain economic value and practical significance.

With the strengthening of the trend of environmental protection and energy conservation, the environmental protection of asphalt mixing plants has gradually become the mainstream form of mixing plant development. What kind of equipment can be called an environmentally friendly asphalt mixing plant? What are the basic conditions that must be met?
First of all, as an environmentally friendly asphalt mixing plant, it must meet the requirement of using less energy consumption during use. That is to say, under the conditions of the same quantity and quality, less energy is consumed during the operation process, including various resources such as water and electricity.
Secondly, environmentally friendly asphalt mixing plants not only require less energy consumption, but also must achieve higher production efficiency, while also reducing carbon emissions in the entire production process, so as to meet the proposed low-carbon production requirements

Bitumen, a black or brown petroleum-like material, has a viscosity ranging from a viscous liquid to a glassy solid. It can be obtained as a residue separated from natural deposits. Bitumen consists of hydrogen and carbon compounds with small amounts of nitrogen, sulfur and oxygen. The preparation of mixed materials for mixing with asphalt is done in several steps:
Prediction: According to the asphalt recipe, the individual components of the aggregate are weighed. Usually this is done using a belt scale, since the material must go to the next step in a continuous flow.

Asphalt mixing station is the standard for mixing asphalt. Having said that, many people still think that this has nothing to do with us. We don’t use asphalt, but do you know that our roads are made of asphalt? When I was a child, I used asphalt to pluck pig hair. The hair on the pig’s head was indeed clean. When using asphalt, it must be burned hot, because if it is cold, it will be very hard and cannot be used. Therefore, if a large amount of asphalt is needed, there must be an asphalt mixer because there is no more convenient equipment than it.
What kind of source material is asphalt that requires special equipment. Asphalt is a black-brown, high-viscosity organic liquid composed of hydrocarbons and non-metallic substances of different molecular weights. The surface is black and soluble in carbon disulfide. At the same time, it is also a waterproof, moisture-proof and anti-corrosion organic gelling material. It can be mainly divided into three types: coal tar asphalt, petroleum asphalt and natural asphalt. Asphalt is mainly used in industries such as coatings, plastics, rubber, and paving roads.

The materials used in asphalt mixtures contain a lot of dust. When the equipment is operating, if the dust enters the atmosphere, it will cause pollution. Therefore, dust removal equipment must be installed, and now bag dust removal is the main method. Safety is a common sense issue. There are well-established standard safety rules.
Do not clean, oil or adjust any mechanical equipment that is not specifically explained during operation; turn off the power and lock it before inspection or repair activities to prepare for accidents. Because each situation has its own particularity. Therefore, be vigilant about safety damage issues, incorrect operation issues and other deficiencies. All of them may lead to accidents, personal injuries, reduced production efficiency, and more importantly, loss of life. Careful and early prevention is the best way to avoid accidents.
Careful and correct maintenance can make the equipment work more efficiently and control it within a certain level of pollution; the maintenance of each component should be carried out according to its operating standards; maintenance plans and safe operation procedures should be formulated according to the inspection and repair conditions that must be carried out.
Take out a work log to record all inspection and repair conditions, list the analysis of each inspection of each component and the description of the repair content or the date of the repair; the second step is to give the inspection cycle for each component, which should be determined according to the service life and wear condition of each component.

The first step in establishing an asphalt mixing station is to determine the host machine and feed batching system. Generally, the configuration is based on the project’s construction period, total amount of concrete, daily concrete consumption and other indicators. The basic principle is to meet the daily concrete consumption. Under normal circumstances, a project can only have one asphalt mixing station, or separate mixing stations can be set up according to zones, or a large mixing station can be set up together with an appropriate number of concrete transport trucks, all of which depend on the actual situation.

Emulsion bitumen equipment has stable product quality, closed material transmission, high degree of automation and civilized production, and is easy to standardize management. The double-mill configuration can be used to produce modified emulsified asphalt.
At present, emulsified asphalt equipment is widely used in new technologies and processes for preventive maintenance, such as fog seal, slurry seal, micro-surfacing, cold regeneration, crushed stone seal, cold mix and cold patch materials.
Emulsion bitumen equipment is an emulsion at room temperature formed by dispersing asphalt into the water phase. It is a new material for the use of elements. Compared with traditional hot asphalt, it saves more than 50% of energy and 10%-20% of asphalt, and has little pollution. The biggest feature of emulsified asphalt is that it can be stored at room temperature. It does not need to be heated during spraying and mixing, nor does it need to heat the stone. Therefore, it greatly simplifies the construction, avoids burns and scalds caused by hot asphalt, and avoids the fumigation of asphalt steam when paving high-temperature mixtures. It is very popular among road maintenance workers.

Asphalt mixing equipment is also divided into fixed and mobile types. There are still big differences between the two to a certain extent. Let’s take a look at the design of mobile asphalt mixing equipment. What advantages can bring to the equipment?

In recent years, asphalt pavement has dominated highway surfaces. With the rapid development of our country’s national economy, highway traffic volume is increasing, axle loads are increasing rapidly, vehicle speeds are increasing, and there are more and more quality problems occurring on asphalt pavements. Some are damaged after repair, and some have a service life of up to Less than design age. This has put forward increasingly higher requirements for the quality of asphalt pavement, and an important factor affecting the performance of asphalt surface layers is the gradation composition of the mixture. This article discusses the mix design of asphalt mixture.

Asphalt mixing stations have always been criticized for pollution due to the emission of harmful smoke and dust and high energy consumption. Asphalt mixing stations with high pollution, high energy consumption and unqualified environmental protection are obviously incompatible with modern urban development. Under the high pressure of environmental protection supervision, how can asphalt mixing stations pass environmental protection inspections smoothly? Can asphalt mixing stations be low-carbon, energy-saving, and environmentally friendly, and achieve environmental protection upgrades?
As a professional asphalt mixing equipment R&D and manufacturer, how to make asphalt mixing stations more environmentally friendly and energy-saving has always been the direction of Nanfang Road Machinery’s efforts. In response to the pollution problems faced by asphalt mixing stations, Nanfang Road Machinery has launched environmentally friendly asphalt mixing equipment with strict environmental protection standards.

Many people think that since both asphalt mixing plants and asphalt mixing plants are equipment for producing asphalt, there should be no difference between them, even if there is, it is only in appearance and volume. However, asphalt mixing plants and asphalt mixing plants are different in even their basic structure and function.
First, let me introduce the basic structure of an asphalt mixing plant, which includes five major components: material supply system, metering system, mixing system, and electrical control system. In comparison, the structure of an asphalt mixing plant is simpler, without so many components, so its operation and maintenance will be simpler.

When using the asphalt mixing plant, you should regularly check the fuel pressure regulating valve or pressure reducing valve to determine whether the surface of the locking nut on the adjustable bolt is clean and removable; if the surface of the screw or nut is too dirty or rusty, it needs to be repaired or Replace the regulating valve.
Check the oil pump regularly to determine whether the sealing device is intact and whether the internal pressure is stable, and replace any damaged or leaking sealing devices. When using hot oil, check whether all oil pipes are well insulated. The filter installed between the oil tank and the oil pump must be cleaned regularly and checked for excessive wear to ensure that the fuel reaches the oil pump smoothly from the oil tank and to reduce the possibility of potential component failure.

With the strengthening of the trend of environmental protection and energy conservation, the environmental protection of asphalt mixing plants has gradually become the mainstream form of mixing plant development. What kind of equipment can be called an environmentally friendly asphalt mixing plant? What are the basic conditions that must be met?
First of all, as an environmentally friendly asphalt mixing plant, it must meet the requirement of using less energy consumption during use. That is to say, under the conditions of the same quantity and quality, less energy is consumed during the operation process, including various resources such as water and electricity.
Secondly, environmentally friendly asphalt mixing plants not only require less energy consumption, but also must achieve higher production efficiency, while also reducing carbon emissions in the entire production process, so as to meet the proposed low-carbon production requirements.

Safety is the key point for any piece of equipment, and asphalt mixers are of course no exception. What I want to share with you is the knowledge in this area, that is, the safe operation specifications of asphalt mixers. You might as well pay attention to it.
In order to prevent the asphalt mixer from moving during work, the equipment should be placed in a flat position as much as possible, and at the same time, use square wood to pad the front and rear axles so that the tires are elevated. At the same time, the asphalt mixer must be provided with secondary leakage protection, and it can only be started after the inspection, trial operation and other aspects are qualified.

Certain failures cannot be avoided during the use of the asphalt mixing plant. For example, a malfunction of the cold material feeding device may cause the asphalt mixing plant to shut down. This may be due to a malfunction in the asphalt mixing plant or due to gravel or foreign matter being trapped under the cold material belt. If it is stuck, if it is a circuit failure, first check whether the motor control inverter of the asphalt mixing station is faulty and whether the line is connected or open.