How to apply for the business license of block asphalt melting equipment?

The base layer of asphalt pavement is divided into semi-rigid and rigid. Since the base layer and the surface layer are materials of different properties, good bonding and continuity between the two are the key requirements for this type of pavement. In addition, when the asphalt surface layer seeps water, most of the water will be concentrated at the joint between the surface layer and the base layer, causing damage such as slurry, looseness, and potholes to the asphalt pavement. Therefore, adding a lower seal layer on top of a semi-rigid or rigid base layer will play a vital role in enhancing the strength, stability and waterproofing capabilities of the pavement structural layer. The more commonly used one is to use asphalt gravel synchronous sealing technology.
So let’s take a look at how the construction of the asphalt gravel synchronous sealing truck is carried out:

The container-type emulsified bitumen equipment hot-melts the base cold-mix colored bitumen and disperses it through the equipment into small cold-mix colored bitumen particles in an aqueous solution containing emulsifier to form a liquid cold-mix colored bitumen material.

Emulsified asphalt is an aqueous suspension of asphalt particles with high interfacial energy. This suspension state is thermodynamically unstable and has the potential to reduce its interfacial area (i.e., through the coagulation process) to a stable state. Preventing this coagulation state (dispersion destruction) is the stabilization effect of the emulsifier protective layer. The stability of emulsified asphalt refers to the ability of asphalt particles to aggregate and cause phase separation, and also refers to the time required for emulsified asphalt to reach equilibrium. That is, the time for asphalt particles to aggregate and separate from water. How can we increase this time? How to prevent emulsified asphalt from demulsifying?

Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreading truck, check the four thermal oil valves and air pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Try running the asphalt pump and cycle for 5 minutes. If the pump head shell is hot to your hands, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not rotate or make noise. You need to open the valve and continue to heat the asphalt pump until it can operate normally.

The advantages of Sinoroader bitumen decanter equipment over similar domestic equipment are reflected in the following points:
1. The equipment produces 8-10t/hour, with an automatic telescopic sealed container structure. It uses an electric hoist to lift the asphalt barrel at the inlet guide tube. Start to control the hydraulic cart forward button, which will promote the barrel push (push and slide into the barrel). It is a 1300mm hydraulic cylinder with a 7.5-ton top thrust. The device has a beautiful appearance, reasonable layout, compactness, stable performance, and is suitable for production under various industrial and mining conditions.
2. Fast barrel removal: According to the principle of layered heating, it adopts four-layer thermal oil heating technology, a single inlet and outlet, and high thermal efficiency of heating; at the same time, it uses the waste heat of combustion gas for two heatings and efficient use of energy; the barrel body uses high-quality rock wool insulation material.
3. Good environmental protection: closed structure, no pollution.
4. No barrel hanging: The upper part of the asphalt barrel is hot, and each is directly affected by the thermal oil heating pipe. The barrel wall directly receives the heat dissipation of the heating coil, and the barrel is clean and fast, which will not cause waste of asphalt barrel hanging.
5. Strong adaptability: Suitable for imported and domestic barrels, and the deformation of asphalt barrels will not affect production.
6. Good dehydration: Use a large-displacement asphalt pump for internal circulation, stirring, water vapor overflows, and is naturally discharged from the exhaust port. After dehydration, asphalt can be directly used to produce asphalt mixture or used as matrix asphalt.
7. Automatic slag removal: This set of equipment has an automatic slag removal function. The filter device sets the asphalt circulation pipeline through the filter, which can automatically remove the barreled asphalt slag.
8. Safe and reliable: The equipment adopts an automatic control system, an automatic ignition burner import, can automatically control the temperature according to the temperature, and is equipped with corresponding monitoring instruments.
9. Convenient relocation: The whole machine is assembled with large components, which is easy to move and quick to assemble.

Each F1 track must be paved with three layers of asphalt, middle and lower, of which the lowest layer is 10 cm coarse asphalt concrete bearing layer, its flatness is less than 8 mm; In the middle is a 4 cm medium grained asphalt concrete bond layer, its flatness is less than 5 mm; The top layer uses 4 cm modified asphalt mixture as the surface wear layer, and the flatness is less than 2 mm.

The paved F1 track cannot have more than 3 points per kilometer of flatness detection, which is much higher than the highway.

Regarding the basic knowledge of modified bitumen plant, I believe that many consumers have already had a basic understanding of it. Because of the continuous development of various fields today, various facilities including modified bitumen plants have been well developed and applied, and modified bitumen plant has gradually been recognized by customers.
The direct quick heating portable equipment in the modified bitumen equipment not only has a faster heating speed, saves fuel, and is pollution-free, but also convenient and easy to operate. The automatic heating system completely eliminates the trouble of baking or cleaning bitumen and pipelines.

The slurry seal truck is one of the main maintenance methods of highways. The slurry seal is made of emulsified asphalt as the binding material, well-graded mineral materials, fillers, water and additives, etc., mixed in a certain proportion. The slurry mixture is evenly spread on the old road surface to be treated with a sealing truck, and is firmly combined with the original road surface to form a new thin layer of asphalt mixture. So what preparations need to be done before construction? Let’s find out below.

No matter the application of emulsified asphalt equipment or other related equipment, in the application of appropriate maintenance work, today we introduce professional technicians to do the following 3 points to effectively improve the utilization rate of asphalt equipment:
1. When the emulsified asphalt plant is out of use for a long time, the liquid in the pipeline and storage tank should be discharged, the lid should be sealed, kept clean, and all moving parts are lubricated. When it is used for the first time and disabled for a long time, the rust of the oil tank should be removed, and the water filter should be cleaned regularly.
2. When the outdoor temperature is lower than -5℃, the emulsified asphalt production equipment shall not store the product without insulation device, and it should be discharged in time to avoid freezing and demulsification of emulsified asphalt.
3. The gap between the stator and the rotor of the emulsified asphalt equipment should be checked regularly. When the machine cannot meet the smaller gap requirements, the stator and rotor should be replaced.

We have conducted in-depth research on asphalt distributors and have accumulated a lot of production technology experience. We have conducted professional and in-depth research on some problems existing in the market to provide convenience for everyone in future production applications.
Every time when spraying asphalt, the asphalt distributor does not spray asphalt. Troubleshooting. The asphalt distributor does not spray asphalt. It is a common fault. The following teaches you how to solve the problem of not spraying asphalt.
1. No asphalt spraying
Analysis of the reasons may be the following reasons:
1. Is the asphalt pump working?
2. Are the valves adjusted correctly?
3. Is the pump or pipeline blocked?
2. Troubleshooting method
1. Check whether the hydraulic system is working properly?
2. After adjusting the valve position, the asphalt distributor must be cleaned to avoid pipeline blockage when used next time. Because the asphalt distributor has different high and low configurations, it can spread various high-viscosity and high-temperature modified asphalts and rubber asphalt in high configuration. If you mistakenly use a low-configuration asphalt truck to spread this type of asphalt, you must spray the asphalt inside the entire vehicle clean after the first use. After spraying, in order to leave no residual asphalt, you can use waste diesel to clean it. Our company’s vehicles are equipped with air cleaning and gravity cleaning devices. Diesel cleaning is a reliable cleaning method.

I believe everyone is familiar with the relevant knowledge about modified bitumen equipment. As users continue to increase its application, we have also talked about it a lot in the above articles and learned that it is mainly engaged in the production of modified bitumen. Production, in order to further enhance users’ understanding of it, professionals summarize its relevant characteristics as follows:

For users of equipment, the amount of material used is the focus of every user. We should attach great importance to this link in the production process. The following is an analysis of the amount of emulsifier used by Gaoyuan manufacturers.
When emulsified asphalt equipment is emulsifying asphalt, the asphalt temperature is better controlled at above 130°C to have better fluidity; 2. The amount of emulsifier is generally 8-14‰ of emulsified asphalt, that is, 8-14kg per ton of emulsified asphalt (asphalt content is more than 50%), and the temperature is 60-70°C. The emulsifier should be used in the middle and upper limit of the production, 10 kg per ton of emulsified asphalt, or 20 kg per ton of water (asphalt content is 50%); the amount of BE-3 emulsifier is generally 18-25‰ of emulsified asphalt, that is, 18-25kg per ton of emulsified asphalt (asphalt content is more than 50%), and the emulsifier solution temperature is 60-70°C. The emulsifier should be used in the upper and middle limits in the first production to ensure successful production. Use 24 kg per ton of emulsified asphalt, or 48 kg per ton of water (asphalt content is 50%). After the production goes smoothly, the dosage can be reduced according to actual conditions.

Fillers used in emulsion bitumen equipment are generally divided into two types: chemically active and non-chemically active. In the production of emulsion bitumen equipment, it can improve the stability of the slurry mixture, speed up or slow down the demulsification speed, and improve the strength of the sealing layer. When adding chemically active fillers, the reaction and compatibility of the fillers with mineral materials and modified emulsion bitumen should be fully considered.

I believe that many people already know about synchronous gravel sealing. But when asked under what circumstances synchronous gravel sealing is suitable, many people cannot tell.
Under what circumstances is synchronous gravel sealing more suitable? According to the technical specifications for the construction of simultaneous gravel sealing, simultaneous gravel sealing can be used for the following disease types:

What key points should be paid attention to when feeding emulsified asphalt equipment? When it comes to emulsified asphalt equipment, I don’t know how much you know about it? What should you pay attention to when adding materials?
The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

Asphalt spreader is used to spread the penetration oil, waterproof layer and bonding layer of the bottom layer of asphalt pavement of high-grade highway. It can also be used for the construction of county and township highway oil roads with layered paving technology. It consists of a car chassis, an asphalt tank, an asphalt pumping and spraying system, a thermal oil heating system, a hydraulic system, a combustion system, a control system, a pneumatic system, and an operating platform.
Knowing how to properly operate and maintain the asphalt spreader can not only extend the service life of the equipment, but also enable the construction project to proceed smoothly. So what problems should the asphalt spreader pay attention to when working? The technicians of Gaoyuan Road Construction Machinery Equipment Co., Ltd. give you tips:
1). Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreader, check the four thermal oil valves and the pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Test the asphalt pump and circulate for 5 minutes. If the pump head shell is hot, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not turn or make noise. In this case, the valve needs to be opened to continue heating the asphalt pump until it can operate normally. During the working process, the asphalt liquid must be kept at a working temperature of 160~180℃, and it cannot be filled too full (pay attention to the liquid level pointer during the injection of asphalt liquid, and check the tank mouth at any time). After the asphalt liquid is injected, the filling port must be closed tightly to prevent the asphalt liquid from overflowing during transportation.
2). During use, asphalt may not be pumped in. At this time, it is necessary to check whether the interface of the asphalt suction pipe is leaking. When the asphalt pump and pipeline are blocked by solidified asphalt, a blowtorch can be used for baking, and the pump must not be forced to turn. When baking, care should be taken to avoid directly baking the ball valve and rubber parts.
3). When spraying asphalt, the car should be driven at a low speed. Do not step on the accelerator hard, otherwise it may cause damage to the clutch, asphalt pump and other components. If 6m wide asphalt is spread, pay attention to obstacles on both sides at any time to prevent collision with the spreading pipe. At the same time, the asphalt should be kept in a large circulation state until the spreading work is completed. After the work is completed every day, if there is any remaining asphalt, it must be returned to the asphalt pool, otherwise it will solidify in the tank and cannot work next time.
4). In addition, the emulsifier must also pay attention to daily maintenance:
1. The emulsifier and delivery pump and other motors, agitators, and valves should be maintained daily.
2. The emulsifier should be cleaned after work every day.
3. The speed regulating pump used to control the flow should be regularly tested for accuracy, and adjusted and maintained in time. The asphalt emulsifier should regularly check the matching clearance between its stator and rotor. When the minimum clearance specified by the machine cannot be reached, the stator and rotor should be replaced.
4. If the equipment is out of use for a long time, the liquid in the tank and pipeline should be emptied (the emulsifier aqueous solution should not be stored for a long time), the hole covers should be tightly closed, kept clean, and the running parts should be filled with lubricating oil. When it is used for the first time or when it is used again after a long period of inactivity, the rust in the tank should be removed, and the water filter should be cleaned regularly.
5. Regularly check whether the terminal in the electric control cabinet is loose, whether the wires are worn during shipment, and remove dust to avoid damage to the machine parts. The frequency converter is a precision instrument. Please refer to the instruction manual for specific use and maintenance.
6. There is a heat transfer oil coil in the emulsifier water solution heating stirring tank. When injecting cold water into the water tank, the heat transfer oil switch should be turned off first, and then the switch should be turned on to heat after adding the required amount of water. Pouring cold water directly into the high-temperature heat transfer oil pipeline can easily cause the weld to crack.

In modern highway maintenance work, how to repair asphalt pavement quickly and effectively has become one of the key issues. As an advanced repair technology, cold patching technology is very popular because of its convenient construction and remarkable effects.
What is the cold patching process?
Cold patching process, as the name suggests, refers to a technical method for repairing asphalt pavement without heating. This process uses a specially proportioned cold-patch asphalt mixture. This material can maintain good fluidity and adhesion even at lower temperatures, thus ensuring the quality of the repair.
Advantages of cold patching process
Fast construction: Cold patching materials can be directly applied to damaged areas without preheating, and are immediately open to traffic, greatly shortening repair time.
All-weather construction: Whether in hot summer or cold winter, cold patching materials can be effectively constructed and are not affected by the weather.
Easy to operate: Thanks to its good working properties, even small damaged areas can be repaired easily.
Environmentally friendly: The construction process reduces environmental pollution and is in line with the concept of green construction.
Application scenarios
The cold patching process is suitable for various types of pavement repair work, especially those places where traffic needs to be restored quickly, such as urban main roads, highway ramps, etc. In addition, the cold patching process is also an ideal choice for remote areas or situations where professional heating equipment is lacking.
In short, the cold patching process has occupied a place in the field of rapid repair of asphalt pavement with its unique advantages and has become an indispensable part of modern highway maintenance.

Emulsified asphalt equipment hot-melts basic colored asphalt and mechanically distributes tiny colored asphalt particles in an aqueous solution containing emulsifier to form a liquid colored asphalt material. The cement emulsified asphalt equipment mortar used in slab ballastless track construction uses cationic emulsified asphalt equipment. The purpose is to adjust the elasticity, toughness and durability of the cement emulsified asphalt equipment mortar. Polymers are often used to modify the asphalt.

Technical features of fiber sealing equipment:
1. Zero starting strong injection technology
With more than ten years of manufacturing history of asphalt spreading trucks and asphalt gravel synchronous sealing trucks, the zero-start strong spraying technology has been accumulated for many years. The combination of time-reliable hydraulic transmission components and Meitong’s control system can make the equipment instantly start from zero. Spraying starts in line, stable and reliable.
2. Duplex sealing structure
The sealing process of this equipment is a three-layer simultaneous and continuous construction process of one layer of asphalt + one layer of fiber + one layer of asphalt, forming a layer of interactive dense network winding structure, which fully meets the user’s construction requirements.

With the rapid development of highway construction and the increase in demand for asphalt, barreled bitumen has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported bitumen used in high-grade highways is in barrel form, which requires an bitumen melter equipment with fast melting speed, clean debarreling, and prevention of asphalt aging.
The upper part of the debarreler of the bitumen melter equipment is hotter, and each barrel is directly heated by the heat transfer oil coil. The barrel wall directly bears the heat radiation of the heating coil. The asphalt is cleanly and sensitively debarreled, and there will be no waste of asphalt hanging barrels. According to the principle of layered heating, four-layer heating technology is adopted, with single inlet and single outlet of heat transfer oil, and high thermal efficiency of heating; at the same time, the waste heat of combustion exhaust gas is used for secondary heating, and power is effectively used; the debarreler body is insulated with high-quality rock wool material. It is suitable for various types of imported and domestic barrels, and the deformation of asphalt barrels will not affect production.

Due to the incorporation of a certain proportion of water into the slurry sealing mixture, it is easy to evaporate in the air. After the water is evaporated, it will become dry and hardened. Therefore, after the slurry is formed, it not only looks very similar to fine-grained asphalt concrete, but does not affect the visual appearance of the road. It also has the same technical properties as fine-grained concrete in terms of wear resistance, anti-skid, waterproofing, and smoothness. Slurry seal technology is used in highway pavement maintenance because of its simple construction technology, short construction period, low cost, high quality, wide application, strong adaptability, etc. It is an asphalt with both economy and high efficiency. Pavement maintenance technology is worthy of application and promotion.

Conventional pit repair techniques are mainly hot material repair and cold filling repair, and warm mixing technology is used to ensure compaction, while there are also some special repair methods such as slurry seal/micro-surface material repair

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing station also needs to be powered on for trial operation before it is officially put into work.

After the emulsified bitumen equipment has been used for a long time, it needs maintenance. There are several points to note when adjusting the emulsified bitumen equipment:
1. During use, regular maintenance should be carried out as appropriate according to the processing materials;
2. For the maintenance and use of the motor, please refer to the motor manual;
3. Most of the random spare parts are national standard and department standard parts, which are purchased all over the country;
4. The colloid mill is a high-precision machine with a line speed of up to 20m/second and a very small grinding disc gap. After inspection and reinstallation, the coaxiality error between the housing and the main shaft must be corrected with a dial indicator ≤0.05mm;
5. When repairing the machine, it is not allowed to be directly knocked with an iron bell during the disassembly, reinstallation and adjustment process. Use a wooden hammer or a wooden block to knock gently to avoid damaging the parts;
6. The machine seals: divided into static and dynamic seals. The static seal uses an O-type rubber ring and the dynamic seal uses a hard mechanical combined seal. If the hard sealing surface is scratched, it should be repaired by grinding on flat glass or flat casting immediately. The grinding material should be ≥200# silicon carbide grinding paste. If the seal is damaged or cracked seriously, please replace it immediately.

Improve the reliability of SBS bitumen emulsion plants: Once you have an established maintenance, it will help to identify problems. This will allow the maintenance plan and time to be carried out at your convenience. Regular maintenance will increase the normal operation time of SBS bitumen emulsification equipment, and it can be used when necessary. Low cost of operation: Imagine an SBS bitumen emulsification plant breaks down during a project. With a protective maintenance plan, such things happen less often because you have taken good care of the SBS bitumen emulsification plant.
If the SBS bitumen emulsification plant wants to maintain normal operation, then in the production process. All stages need to be maintained normal, among which the normality of the circuit system is an important aspect to ensure its smooth operation. Imagine that if there is a problem with the circuit during the on-site operation, it may affect the development of the entire project.
For users, of course, they don’t expect this to happen, so if the SBS bitumen emulsification plant is in the work of using the SBS bitumen emulsification equipment, if there is a circuit problem, it is necessary to take appropriate measures to solve it in time. The following article will give a detailed description of this problem, and the following SBS bitumen emulsification plant can be of benefit to everyone.

This set of emulsified asphalt production equipment includes water treatment, water storage tanks, water active metering and temperature control systems, asphalt storage tanks, asphalt external temperature systems, hot water pump soap batching systems, soap temporary storage tanks, soap transfer pumps, soap liquid It consists of external temperature system and metering system, filter, hot asphalt transfer pump and metering system, three-stage pipeline emulsifier, emulsified asphalt cooling system and recovery equipment, product tank and electrical automatic control system.
The entire process is modularly designed, and users can freely combine and select according to their needs. The equipment of each part is used as follows: Water treatment system: Mechanical filtration of ordinary tap water absorbs resin exchange reactions, turning high-hardness tap water into pure soft water and reducing water tension. , enhance the emulsification effect of asphalt or modified asphalt.

Bitumen melter equipment plays an important role in highway construction, but traditional heating methods have problems such as high energy consumption and low efficiency. This article introduces a new type of bitumen melting plant, which uses electric heating technology and has the advantages of energy saving, environmental protection and environmental protection. The working principle of this equipment is to heat the bitumen through the heat generated by the resistance wire, and then automatically adjust the temperature and flow rate through the control system to achieve the best melting effect.

During the road construction process, asphalt spreaders also play an irreplaceable role. Let’s take a look at the main performance advantages of asphalt spreaders produced by Sinoroader and where their main contributions exist?
1. Manual/automatic control of spraying volume and working width. Each nozzle can be controlled individually, and the determinant nozzles can be freely combined to adjust the spraying width at will. Spreading control can be performed in the cab or the rear platform.
2. The automatic control system can measure the vehicle speed and automatically calculate the number of revolutions of the asphalt pump according to the input spreading volume, spraying width and asphalt type, and then automatically adjust the number of asphalt pumps through the system.
3. The vehicle-mounted rapid heating system (10-15℃/h) can improve the heating efficiency and reduce the construction auxiliary time and spreading temperature;
4. The flushing nozzle system can blow out the remaining asphalt in the nozzle through diesel and high-pressure air to prevent the asphalt from freezing in the nozzle and increase the service life of the nozzle.

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.
For the block asphalt melting equipment, the Provincial Environmental Protection Department will review the application materials, and appoint the Provincial Block Asphalt Melting Equipment Management Office to organize relevant doctors to conduct technical evaluation and on-site technical evaluation, and produce expert technical evaluation opinions and on-site inspection reports. Then report the materials of the block asphalt melting equipment to the meeting of directors for scientific research and make a review decision.