How to maintain the engine of synchronous sealing vehicle

The difficulty of emulsified bitumen equipment itself, because general bitumen also has different classifications, in the production and processing of emulsified bitumen equipment bitumen concrete, it is necessary to pay attention to whether the common raw materials are the common bitumen and ensure the quality. Check the black antistatic tweezers of emulsified bitumen equipment asphalt concrete machine equipment emulsified bitumen equipment.
If the gap of the black antistatic medical tweezers bitumen concrete micro-powder machine of emulsified bitumen equipment is enlarged after long-term use, then we can adjust it and continue to process it. Emulsified bitumen equipment is a relatively simple difficulty.

After the rubber bitumen storage tank is cleaned, the wood chips are sent to the rubber bitumen storage tank, and the wood chips and the bottom of the rubber bitumen storage tank are wiped with wood chips. The dirt and wood chips in the bitumen tank can be weathered naturally. The rubber bitumen storage tank is not allowed to be damaged. Check the technical specifications of the underwater concrete processing equipment and ventilation equipment.
The bottom of the rubber bitumen storage tank drain pipe is discharged from the drainage pipe, and the waste water is discharged into the empty tank or other containers through the inlet and outlet and the self-draining pipe. Open the Shenzhen manhole into the plastic suction pipe and pave the Shenzhen manhole with asbestos to reduce the discharge of oil and gas. When manually pumping the bottom oil, two people should be operated to improve the labor efficiency of the workers and send the fuel tank to supervision.

There are many types of emulsified asphalt (composition: asphaltene and resin) equipment. Emulsified asphalt (composition: asphaltene and resin) equipment can be divided into intermittent operation type, semi-continuous operation type, and Continuing the three operating types, what is the knowledge about different types of emulsified asphalt equipment?

This set of emulsified asphalt production equipment includes water treatment, water storage tanks, water active metering and temperature control systems, asphalt storage tanks, asphalt external temperature systems, hot water pump soap batching systems, soap temporary storage tanks, soap transfer pumps, soap liquid It consists of external temperature system and metering system, filter, hot asphalt transfer pump and metering system, three-stage pipeline emulsifier, emulsified asphalt cooling system and recovery equipment, product tank and electrical automatic control system.
The entire process is modularly designed, and users can freely combine and select according to their needs. The equipment of each part is used as follows: Water treatment system: Mechanical filtration of ordinary tap water absorbs resin exchange reactions, turning high-hardness tap water into pure soft water and reducing water tension. , enhance the emulsification effect of asphalt or modified asphalt.

Analysis of the necessity of emulsified bitumen equipment in modern road construction projects With the acceleration of the construction speed of transportation infrastructure, the construction standards are getting higher and higher, and higher requirements are also put forward for the use of emulsified bitumen in the closed layer of fly ash and the adhesive layer between the new and old ground.

The emulsified bitumen equipment hot-melts the base cold-mix colored bitumen, and then disperses the slightly cold-mixed colored bitumen particles into the aqueous solution containing emulsifier through a machine to form liquid cold-mixed colored bitumen sheets.

Synchronous gravel sealing technology refers to the use of special synchronous gravel sealing truck equipment to lay and roll prepared gravel, asphalt and other materials to build a single layer of asphalt gravel wearing layer, which is important for highway pavement. protection of. From the perspective of characteristics, it is simple and easy to implement. It has obvious effects on the prevention of highway diseases, problem solving, later maintenance, and improvement of grade protection. It can also well extend the service life of highways.

Recently, I found that many people don’t know much about the operation skills of asphalt pavement spreaders. If you also want to know what’s going on, you can read this introduction below.
Asphalt pavement spreaders are an indispensable and important equipment in road maintenance and construction. Their operation skills directly affect construction efficiency and project quality. The following introduces the operation skills of asphalt pavement spreaders from four aspects: pre-operation preparation, precautions during construction, spreading skills, and post-operation cleaning and maintenance:

Fillers used in emulsion bitumen equipment are generally divided into two types: chemically active and non-chemically active. In the production of emulsion bitumen equipment, it can improve the stability of the slurry mixture, speed up or slow down the demulsification speed, and improve the strength of the sealing layer. When adding chemically active fillers, the reaction and compatibility of the fillers with mineral materials and modified emulsion bitumen should be fully considered.

With the development of science and technology, the emergence of emulsified asphalt tanks has brought great convenience to our work, and is widely used in every site. So what issues need to be paid attention to when filling emulsified asphalt tanks? Below, the editor will introduce to you the relevant knowledge structure diagram, hoping to be of some help to you.

The slurry seal truck is one of the main maintenance methods of highways. The slurry seal is made of emulsified asphalt as the binding material, well-graded mineral materials, fillers, water and additives, etc., mixed in a certain proportion. The slurry mixture is evenly spread on the old road surface to be treated with a sealing truck, and is firmly combined with the original road surface to form a new thin layer of asphalt mixture. So what preparations need to be done before construction? Let’s find out below.

Asphalt melting equipment follows the continuous development of urbanization. Whether in rural areas or in big cities, you can see a lot of construction sites, among which it is inevitable that asphalt melting equipment is set up nearby. Asphalt melting equipment manufacturers, whether large or small asphalt melting equipment or relatively large and small, although it is just a simple mechanical equipment, but to move or transport it, it is a small matter, and there are many places that require attention.
The technical level of the asphalt melting equipment disassembly and assembly team directly affects the disassembly and assembly progress of the asphalt melting equipment; improve on-site supervision, reasonably organize disassembly and assembly machinery and equipment and workers, try to avoid cross-operation, and promote the disassembly and assembly process to consume less manpower and machinery shifts to do a good job in the transportation of asphalt melting equipment; ensure that the asphalt melting equipment is not damaged and the prefabricated components are not missed.

The main filter material of stainless steel barrel removal adopts five-layer sintered mesh. Standard five-layer calcination is made by stacking and vacuum calcining five layers of stainless steel barrel removal wire mesh. The stainless steel barrel made of it has corrosion resistance, good water permeability, high compressive strength, easy cleaning and back-cleaning, high filtration precision, hygienic and clean filter material, and stainless steel barrel removal wire mesh does not fall off.
Double-layer metal sintered mesh is a new type of filtration system with high impact toughness and overall rigidity, which is made by stacking and vacuum calcining double-layer stainless steel barrel removal wire mesh products.

Asphalt used to pave roads. It can be obtained by regular vacuum distillation of crude oil with appropriate properties, and can also be obtained by shallow oxidation of vacuum residue or propane deasphalting process. It can also be prepared by mixing asphalt of different duction and injection degree

There are certain standards for the composition and mix ratio of micro-surfacing, and a wide range of materials are used, including polymer-modified emulsified asphalt, various aggregates, cement, water, additives, etc. Raw material quality has a significant impact on microsurfacing performance, so understanding the performance of each component and the key factors that influence its performance is critical to ensuring the quality of your microsurfacing mix.

1 Common diseases of asphalt pavement
There are nine phenomena of early damage to asphalt pavement: rutting, cracks, and potholes. These diseases are the most common and serious, and are one of the common quality problems of highway projects.
1.1 Rutting
Rutting refers to the longitudinal strip grooves on the road surface along the wheel tracks, with a depth of more than 1.5cm. Rutting is a strip groove formed by the accumulation of permanent deformation of the road surface under the repeated action of vehicle load. Rutting reduces the smoothness of the road surface. When the rutting reaches a certain depth, due to the accumulation of water in the rutting, it is easy for cars to slide and cause traffic accidents. The main reasons for rutting are unreasonable design and serious overloading of vehicles.
1.2 Cracks
There are three main forms of cracks: longitudinal cracks, transverse cracks and mesh cracks. When cracks occur in asphalt pavement, water seepage occurs, which harms the surface layer and base layer.
1.3 Potholes
Potholes are common early diseases of asphalt pavement, which refer to the road surface being damaged into potholes with a depth of more than 2cm and an area of ??more than 0.04㎡. The main reason for the formation of potholes is that the oil used in vehicle repair or motor vehicles seeps into the road surface, polluting the asphalt mixture and causing it to loosen. The pits are gradually formed by driving and rolling.

Asphalt melting equipment is a mechanical equipment specially used to heat and melt asphalt. Our company’s products have been widely recognized and applied in the market.
Our main production process is: transporting the high-temperature oil and gas generated after high-temperature cracking of raw materials (such as petroleum) in the combustion chamber to high-speed rotating heat-conducting oil tankers for heat transfer, melting, cooling and other processes, and finally obtaining the required finished materials or Semi-finished materials. The advantage is that it can make the best use of raw materials and reduce energy consumption; at the same time, it can also customize products of different specifications according to different needs to meet the different requirements of customers. In addition, we provide after-sales service and technical support to protect the interests and safety of our customers.

Emulsified asphalt can be spread by mechanical spreading and manual spreading. Different spreading methods will have different effects on pavement performance, so it is very important to choose the right spreading method. At the same time, maintenance and management after spreading are equally important to ensure the safety and durability of the pavement.
Emulsified asphalt is a common pavement material that is widely used in road construction and maintenance. There are two main ways to spread emulsified asphalt: mechanical spreading and manual spreading. Mechanical spreading generally uses a special spreading vehicle that can quickly and evenly spread emulsified asphalt. Manual spreading is carried out by workers using tools such as brushes or rollers, which is suitable for pavement treatment in small areas or special areas.
Different spreading methods also have different effects on pavement performance. Mechanical spreading can quickly complete large-area treatment and spread evenly, which is conducive to ensuring the flatness and anti-skid properties of the pavement. Manual spreading can more finely treat special areas such as shoulders and intersections to improve the overall performance of the pavement.

Modified material bitumen stripper, if the definition is simple, is an bitumen stripper. If described in detail, modified materials such as rubber powder or other fillers are added to the bitumen stripper, or an bitumen stripper is used to Block chemical substances such as photooxygen catalysis. The first is to change the chemical composition of the bitumen stripper, and the second is to use modified materials to equip the stripper with a certain spatial network structure, thereby improving its performance. Modified bitumen strippers mainly include vulcanized rubber and thermoplastic polyurethane elastomer modified bitumen strippers, plastic and anti-corrosion coating modified bitumen strippers and polymer modified bitumen strippers.

The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) Open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

Whether it is the application of modified asphalt equipment or the application of other equipment, if you want to extend its service life, you need to do daily maintenance work. In order to better help everyone, we have modified asphalt The maintenance methods that can be adopted when using the equipment are introduced as follows:

To ensure good operation of asphalt melting equipment and extend its service life, regular maintenance and repairs are required. The following are specific maintenance and repair steps:
First, various parts of the equipment, including heating elements, pipes, valves, etc., need to be inspected regularly to make sure they are not worn or damaged. If any problems are found, they should be repaired or replaced immediately.

Everyone has a side of themselves that they don’t want others to know. As a preventive road maintenance technology, slurry sealing has some shortcomings. do you think so?
Slurry seal is a kind of road protection that uses special equipment to mix emulsified asphalt, water, additives, aggregates, fillers and other ingredients in a certain proportion, and then mixes the slurry mixture onto the original road surface to form a thin layer. Maintenance technology. These are all well known. The editor will not go into details on this.

Everyone must be familiar with slurry sealing and micro-surfacing. But do you know their 7 construction steps?
Slurry sealing and micro-surfacing were both early preventative highway protection technologies. Its function is to ensure the smooth use and extended life of the highway. The construction steps are as follows:

Asphalt spreading trucks are used to spread the permeable oil layer, waterproof layer and bonding layer of the bottom layer of asphalt pavement on high-grade highways. It can also be used in the construction of county and township-level highway asphalt roads that implement layered paving technology. It consists of a car chassis, an asphalt tank, an asphalt pumping and spraying system, a thermal oil heating system, a hydraulic system, a combustion system, a control system, a pneumatic system, and an operating platform.

Technical features of fiber sealing equipment:
1. Zero starting strong injection technology
With more than ten years of manufacturing history of asphalt spreading trucks and asphalt gravel synchronous sealing trucks, the zero-start strong spraying technology has been accumulated for many years. The combination of time-reliable hydraulic transmission components and Meitong’s control system can make the equipment instantly start from zero. Spraying starts in line, stable and reliable.
2. Duplex sealing structure
The sealing process of this equipment is a three-layer simultaneous and continuous construction process of one layer of asphalt + one layer of fiber + one layer of asphalt, forming a layer of interactive dense network winding structure, which fully meets the user’s construction requirements.

Precautions during the production of emulsified bitumen equipment. How much do you know about this information? Let’s learn more about it:
When the emulsified bitumen equipment is in production, the viscosity of the bitumen decreases with the increase of temperature. For every 12℃ increase, its dynamic viscosity decreases by about one time. During production, the base bitumen should be heated to liquid state before emulsification. In addition, in order to adapt to the emulsification capacity of the colloid mill, the base bitumen dynamic viscosity is generally controlled to be about 200cst. The lower the temperature, the higher the viscosity, which increases the burden on the bitumen pump and the colloid mill, making it difficult to emulsify; but on the other hand, in order to prevent the demulsification caused by excessive vaporization and evaporation of water in the finished product during the production of emulsified bitumen, it is impossible to heat the base bitumen temperature too high. Generally, the finished product temperature at the outlet of the colloid mill should be controlled to be less than 85℃.

There are many ways to heat bitumen, including using fire source heating, electric heating, steam heating, hot water heating and indirect heating. Fire source heating generates heat by burning fuel to heat the bitumen to a molten state. Electric heating converts electrical energy into thermal energy through electric heating elements to heat the bitumen to a molten state. Steam heating transfers heat to bitumen through steam, heating the bitumen to a molten state. Hot water heating transfers heat to the bitumen through hot water, heating the bitumen to a molten state. Indirect heating transfers heat to the heating medium, which then transfers the heat to the bitumen to heat the bitumen to a molten state.

Modified (rubber powder) bitumen equipment, one of the road maintenance equipment. It is a kind of equipment that measures, mixes and develops SBS, rubber powder and asphalt.
Modified (rubber powder) bitumen equipment is a set of wet modification processing technology, which mainly consists of modified material metering and promotion, bitumen rapid heating, asphalt metering, high-intensity mixing tank, mixed material transfer pump, development tank, colloid mill, Control system and other components.