How to produce efficient emulsified asphalt?

1 Common diseases of asphalt pavement
There are nine phenomena of early damage to asphalt pavement: rutting, cracks, and potholes. These diseases are the most common and serious, and are one of the common quality problems of highway projects.
1.1 Rutting
Rutting refers to the longitudinal strip grooves on the road surface along the wheel tracks, with a depth of more than 1.5cm. Rutting is a strip groove formed by the accumulation of permanent deformation of the road surface under the repeated action of vehicle load. Rutting reduces the smoothness of the road surface. When the rutting reaches a certain depth, due to the accumulation of water in the rutting, it is easy for cars to slide and cause traffic accidents. The main reasons for rutting are unreasonable design and serious overloading of vehicles.
1.2 Cracks
There are three main forms of cracks: longitudinal cracks, transverse cracks and mesh cracks. When cracks occur in asphalt pavement, water seepage occurs, which harms the surface layer and base layer.
1.3 Potholes
Potholes are common early diseases of asphalt pavement, which refer to the road surface being damaged into potholes with a depth of more than 2cm and an area of ??more than 0.04㎡. The main reason for the formation of potholes is that the oil used in vehicle repair or motor vehicles seeps into the road surface, polluting the asphalt mixture and causing it to loosen. The pits are gradually formed by driving and rolling.

The bitumen (composition: asphaltene and resin) drum melting machine adopts a self-heating integrated structure, which integrates the thermal oil boiler used in the old asphalt drum melting machine and the barrel removal equipment itself, reducing the volume of the entire equipment and significantly It reduces equipment investment (actual significance: it is the accumulation of future profits), saves the space occupied by the equipment and the logistics cost of switching sites. The combustion chamber is placed inside the equipment itself, which greatly reduces thermal damage and improves heat utilization.

Asphalt melting equipment follows the continuous development of urbanization. Whether in rural areas or in big cities, you can see a lot of construction sites, among which it is inevitable that asphalt melting equipment is set up nearby. Asphalt melting equipment manufacturers, whether large or small asphalt melting equipment or relatively large and small, although it is just a simple mechanical equipment, but to move or transport it, it is a small matter, and there are many places that require attention.
The technical level of the asphalt melting equipment disassembly and assembly team directly affects the disassembly and assembly progress of the asphalt melting equipment; improve on-site supervision, reasonably organize disassembly and assembly machinery and equipment and workers, try to avoid cross-operation, and promote the disassembly and assembly process to consume less manpower and machinery shifts to do a good job in the transportation of asphalt melting equipment; ensure that the asphalt melting equipment is not damaged and the prefabricated components are not missed.

Asphalt spreading truck is a kind of black ground construction machinery. It is an important equipment in the logistics construction of roads, municipal roads, airports and ports. This equipment is mainly used to spray different types of asphalt on the ground to meet the construction requirements of different levels of ground oil permeable layer, sticky layer, left and right permeable layer, fog permeable layer, etc.

How to reduce the energy consumption of emulsified asphalt production equipment is a concern of many users, and is also an issue that many manufacturers attach great importance to. Therefore, today Sinoroader, as a manufacturer of emulsified asphalt production equipment, would like to take this opportunity to share with you how to reduce the production of emulsified asphalt. Equipment energy consumption method.
Since emulsified asphalt appears as a finished product in emulsified asphalt production equipment, and the outlet temperature of ordinary emulsified asphalt is about 85°C, the outlet temperature of emulsified modified asphalt is above 95°C, so there is a lot of latent heat in emulsified asphalt, but emulsified asphalt The production equipment does not make good use of them, but directly enters the finished product tank, allowing the heat to be lost at will, resulting in a waste of energy.

Sinoroader emulsifier does not need to add acid or adjust pH value in the production of emulsified asphalt, thus reducing the process, reducing equipment maintenance, saving labor and materials. It reduces the cost of emulsified asphalt, produces acid-free, eliminates equipment corrosion emulsion, does not consider anti-corrosion measures in the selection of equipment, and greatly reduces the capital investment of equipment.
Main technical indicators:
Active ingredient content 40±2%
pH value 8-7
Appearance: yellow or dark yellow liquid
Odor: non-toxic, aromatic gas
Solubility: soluble in water and some organic solvents
Temperature ratio:
Water temperature: 70℃-80℃
Asphalt temperature: 140℃-150℃
Emulsifier: 8%-10%
Asphalt ratio: water = 4:6
Precautions:
The temperature of the emulsifier aqueous solution should not exceed 70%
When the temperature is low, the product is in a paste or paste, and the heating is variable.
Different varieties of asphalt should adjust the amount of emulsifier, and the use test should be derived from the test.

Emulsified asphalt equipment hot-melts basic colored asphalt and mechanically distributes tiny colored asphalt particles in an aqueous solution containing emulsifier to form a liquid colored asphalt material. The cement emulsified asphalt equipment mortar used in slab ballastless track construction uses cationic emulsified asphalt equipment. The purpose is to adjust the elasticity, toughness and durability of the cement emulsified asphalt equipment mortar. Polymers are often used to modify the asphalt.

With reliable performance and stable benchmark quality, Sinoroader slurry sealer is favored by customers and was once in short supply. Sinoroader slurry sealer uses emulsified asphalt, which can reduce the sensitivity of construction temperature and effectively extend the construction time. Sinoroader slurry sealer has fast molding, improves construction speed, shortens road construction time, and reduces the manpower and material resources required for construction. In addition, in terms of energy saving and consumption reduction, Sinoroader slurry sealer can be constructed at room temperature, achieving “0 release” of harmful gases, reducing air pollution, and is very green and environmentally friendly.

Preventive pavement maintenance is a periodic mandatory maintenance measure, which is taken to restore the pavement surface service function when the pavement structure strength is sufficient and only the surface function is attenuated. New preventive maintenance technologies such as super-viscous fiber-added low-noise micro-surfacing and synchronous gravel seal have been widely used on the main lines of national highways, and the construction effect has been widely praised by customers.
Super-viscous fiber-added low-noise micro-surfacing starts with the gradation of micro-surfacing and the main material modified emulsified asphalt. By reducing the structural depth of the micro-surfacing and changing the distribution state of the coarse and fine materials on the surface of the micro-surfacing, the driving noise is reduced, while ensuring its anti-skid performance, effectively improving its adhesion, waterproofness, durability and crack resistance, and can solve the defects of easy detachment, excessive noise and reflective cracks of ordinary micro-surfacing.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing station also needs to be powered on for trial operation before it is officially put into work.

In the cold winter, you need to pay attention to the following points when using asphalt melting equipment:
1. Protection from cold and warmth: The equipment needs to be operated indoors or in a place with shading facilities, and ensure that the temperature of the equipment and the surrounding environment is maintained within an appropriate range.
2. Check the equipment: Before use, the equipment should be checked, including whether the circuits, fluid circuits and other parts of the equipment are working normally, and whether there are any leaks of electricity or water in the equipment.
3. Pay attention to safety: During operation, you should wear protective equipment and avoid direct contact with hot asphalt. At the same time, it is necessary to avoid equipment overload operation and prevent equipment damage and safety accidents.
4. Control speed: Reasonably control the working speed of the equipment according to weather conditions and road conditions to avoid overheating of the equipment, causing asphalt to flow too quickly or burn.
5. Storage conditions: When not in use, place the device in a dry, ventilated place with moderate temperature, and ensure that any residue in the device is completely removed.

Some of the equipment of emulsified modified bitumen equipment are as follows. The specially made bitumen filter can effectively filter the residues and dirt in the high-temperature culture medium bitumen to avoid damage to the subsequent equipment. The emulsified modified bitumen equipment adopts a spiral plate type or a shell and tube heat exchanger to quickly heat the culture medium bitumen through high-temperature heat transfer oil to meet the needs of the production process. The emulsified modified bitumen equipment is heated in the storage tank to prevent the bitumen from aging due to long-term high-temperature heating and exposure to the air. The sulfate generated during the production process of the emulsified modified bitumen equipment is very limited, reducing air pollution.
The emulsified modified bitumen equipment sends the modified material manually poured into the dumping bin to the bitumen batching tank by wind or spiral. It can be equipped with a metering and calibration system. The emulsified modified bitumen equipment thickener is automatically or manually added. The emulsified modified bitumen equipment can be equipped with a metering and calibration system. Emulsified modified bitumen equipment transportation and metering and calibration system, the emulsified modified bitumen equipment adds the set bitumen amount to the batching tank through the frequency converter and computer interlock. The emulsified modified bitumen equipment and bitumen steam flowmeter use big brand products to ensure the preparation.

The engine is the source of power for the vehicle. If the synchronous sealing vehicle wants to perform normal construction operations, it must ensure that the engine is in good condition. Routine maintenance is an important means to effectively prevent engine failure. How to maintain it is determined by Xinxiang Junhua Special Vehicle Vehicles Co., Ltd. will take everyone to understand.

Precautions during the production of emulsified bitumen equipment. How much do you know about this information? Let’s learn more about it:
When the emulsified bitumen equipment is in production, the viscosity of the bitumen decreases with the increase of temperature. For every 12℃ increase, its dynamic viscosity decreases by about one time. During production, the base bitumen should be heated to liquid state before emulsification. In addition, in order to adapt to the emulsification capacity of the colloid mill, the base bitumen dynamic viscosity is generally controlled to be about 200cst. The lower the temperature, the higher the viscosity, which increases the burden on the bitumen pump and the colloid mill, making it difficult to emulsify; but on the other hand, in order to prevent the demulsification caused by excessive vaporization and evaporation of water in the finished product during the production of emulsified bitumen, it is impossible to heat the base bitumen temperature too high. Generally, the finished product temperature at the outlet of the colloid mill should be controlled to be less than 85℃.

Bitumen emulsion equipment is widely used in new technologies and new processes for preventive maintenance. Bitumen emulsion plant is an emulsion at room temperature formed by dispersing bitumen into the water phase. It is a new material that is made of natural materials. It is different from traditional Compared with hot bitumen, it saves more than 50% of energy, saves 10%-20% of bitumen, and causes less pollution.

In the cold winter, the following points should be noted when using bitumen melter equipment:

1. Keep warm: The bitumen melter equipment needs to be operated indoors or in a place with sunshade facilities, and ensure that the temperature of the bitumen melter and the surrounding environment is kept within an appropriate range.
2. Check the bitumen melting equipment: Before use, the bitumen melter should be checked, including whether the circuit, liquid circuit and other parts of the equipment are working properly, and whether the equipment has leakage, water leakage and other conditions.
3. Pay attention to safety: During operation, protective bitumen melter equipment should be worn to avoid direct contact with hot bitumen. At the same time, avoid overloading the bitumen melter to prevent equipment damage and safety accidents.
4. Control speed: Reasonably control the working speed of the bitumen melting equipment according to weather conditions and road conditions to avoid overheating of the equipment, which may cause the bitumen to flow too quickly or burn.
5. Storage conditions: When not in use, place the equipment in a dry, ventilated and moderately warm place, and ensure that the residue in the equipment is completely cleaned.

Synchronous chip seal is a process technology for treating cracks in asphalt pavement, and it is currently a highway construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical characteristics are? If you don’t know, follow the editor of Sinoroader company to have a look.

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.
For the block asphalt melting equipment, the Provincial Environmental Protection Department will review the application materials, and appoint the Provincial Block Asphalt Melting Equipment Management Office to organize relevant doctors to conduct technical evaluation and on-site technical evaluation, and produce expert technical evaluation opinions and on-site inspection reports. Then report the materials of the block asphalt melting equipment to the meeting of directors for scientific research and make a review decision.

Asphalt used to pave roads. It can be obtained by regular vacuum distillation of crude oil with appropriate properties, and can also be obtained by shallow oxidation of vacuum residue or propane deasphalting process. It can also be prepared by mixing asphalt of different duction and injection degree

Asphalt used to pave roads. It can be obtained by regular vacuum distillation of crude oil with appropriate properties, and can also be obtained by shallow oxidation of vacuum residue or propane deasphalting process. It can also be prepared by mixing asphalt of different duction and injection degree

Asphalt spreader is an irreplaceable tool for highway maintenance. Asphalt spreader is an irreplaceable tool for highway maintenance. Highway maintenance is divided into four categories according to the nature of the project, scale, and technical complexity: minor repair, medium repair, major repair, and improvement. Specific classification:
(1) Minor repair and maintenance project: preventive maintenance and repair of slightly damaged parts of the highway and all its engineering facilities to keep them in good condition. It is usually planned and carried out daily by the maintenance team within the annual minor repair and maintenance quota funds on a monthly (ten-day) basis.
(2) Medium repair project: regular repair and reinforcement of general wear and tear and local damage of highway engineering facilities to restore them to their original state. It is usually planned and implemented by grassroots road maintenance agencies on an annual (seasonal) basis.
(3) Major repair project: periodic comprehensive repair of major damage to highway facilities to fully restore them to the original design standards, or local improvements and individual additions within the original technical level to gradually improve the highway’s traffic capacity. It is usually organized and implemented by grassroots road maintenance agencies or with the help of their superior agencies according to the approved annual project budget.
(4) Improvement projects are large projects that improve the technical level of roads and their engineering facilities in stages and sections due to their inability to meet traffic volume and load requirements, or significantly improve traffic capacity through improvements. It is usually organized and implemented or completed through bidding by regional road maintenance agencies or provincial road maintenance agencies according to the approved plan and design budget. As a manufacturer of asphalt spreaders, we welcome you to visit us.

Conventional pit repair techniques are mainly hot material repair and cold filling repair, and warm mixing technology is used to ensure compaction, while there are also some special repair methods such as slurry seal/micro-surface material repair

The viscosity of the bitimen melter equipment decreases as the temperature increases during the production process. Its output viscosity is about twice as high as every 12°C increase. During production, the base bitimen melter equipment must first be heated to a liquid state and then emulsified. In order to better integrate the emulsification ability of colloid milling, the viscosity of base bitimen melter is generally controlled to be about 200 cst. The lower the temperature, the higher the viscosity, which increases the pressure on the bitimen melter pump and colloid milling, making emulsification impossible: However, on the other hand, in order to prevent the asphalt debarrel equipment from weaning when the moisture of th

Fillers used in emulsion bitumen equipment are generally divided into two types: chemically active and non-chemically active. In the production of emulsion bitumen equipment, it can improve the stability of the slurry mixture, speed up or slow down the demulsification speed, and improve the strength of the sealing layer. When adding chemically active fillers, the reaction and compatibility of the fillers with mineral materials and modified emulsion bitumen should be fully considered.

Asphalt emulsifier is an emulsifier that belongs to the category of surfactants and is a raw material for the production of emulsified asphalt.
Emulsifiers are divided into: synthetic emulsifiers, natural emulsifiers, inorganic powder emulsifiers, etc. Currently, synthetic emulsifiers are widely used. Asphalt emulsifier is a type of chemical organically synthesized surfactant.

Colored asphalt pavement is a kind of special pavement material that mixes colored particles into asphalt and then lays on the pavement

Contemporary roads and pavements have undergone many changes: traffic volume and driving frequency have increased significantly, the axle load of logistics trucks has continued to increase, one-way driving in separate lanes has been widely implemented, and regulations have further improved the anti-flow resistance of the ground, that is, the work of modified asphalt equipment under high temperatures ability;

From three aspects, emulsion bitumen equipment has good economic performance:
First, energy saving. The kerosene or gasoline content in diluted asphalt can reach 50%, while the emulsion bitumen plant only contains 0-2%. This is a valuable saving behavior in the production and utilization of white fuel. By simply increasing the viscosity standard of asphalt by adding light oil solvent, asphalt can be poured and spread, and it is hoped that the light oil after use can evaporate into the atmosphere.
Second, versatility. There are many application methods for emulsion bitumen plants, and the appropriate method needs to be selected when applying it. The same emulsion can be used for large-scale sealing and can be used for small-scale pit repair work. Because they can be stored in tanks for a long time, they are very easy to use when applied in remote areas.
Third, it is easy to use. The professional spreading of emulsions requires professional equipment, such as spreaders. Small-area emulsion applications can be directly poured and spread by hand, such as small-area pit repair work, crack fillers, etc. Small quantities of cold mixes only require basic equipment.

Asphalt mixture mixing equipment is a factory-style complete set of equipment that mixes dry and heated aggregates of different particle sizes, fillers and asphalt according to the designed mix ratio at a specified temperature into a uniform mixture. It is widely used in high-grade highways and urban roads. , airports, docks, parking lots and other engineering construction. It is a key equipment for asphalt pavement construction, and its performance directly affects the quality of asphalt pavement.
Generally, there are two types of asphalt concrete mixing equipment: intermittent type and continuous type. The continuous process flow is simple and the equipment is simplified. As for the intermittent forced mixing equipment, due to the secondary screening of aggregates, various components are measured in batches, and forced stirring and mixing can reliably ensure gradation, and the measurement of powder and asphalt can also achieve very high accuracy; so the mixing equipment The asphalt mixture produced is of high quality and can meet various construction requirements.