Installation of main components of asphalt station

The asphalt mixing plant is constructed according to a certain process, which can not only ensure the construction quality, but also ensure that the asphalt mixing plant is not damaged. Although the construction details are critical, the key skills of the asphalt mixing plant construction must be mastered.
Before the construction of the asphalt mixing plant, the top surface of the asphalt mixing plant construction range should be removed, and the dry and flat site elevation should be kept to meet the design requirements. If the ground surface is too soft, the foundation should be reinforced to prevent the construction machinery from becoming unstable and to ensure that the pile frame is vertical.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing plant also needs to be powered on for trial operation before it is officially put into work.
The first step in commissioning is to run a single motor and check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

After use, asphalt mixing equipment needs to be disassembled, cleaned, and maintained before it can be saved for next use. Not only is the disassembly process of the equipment important, but the previous preparation work also has a greater impact, so it cannot be neglected. Please pay attention to the detailed introduction below for specific content.

What should I do when the reversing valve in the asphalt mixing plant fails? The editor has a trick:
1. The reversing valve cannot be reversed or the reversing action is slow, which is generally caused by poor lubrication, stuck or damaged springs, oil or impurities stuck in the sliding parts. In this regard, you should first check whether the oil mist is working normally; whether the viscosity of the lubricating oil is appropriate. If necessary, the lubricating oil should be replaced, the sliding part of the reversing valve should be cleaned, or the spring and reversing valve should be replaced.

In fact, asphalt mixing stations are not uncommon in our daily lives. They are mainly a unit of equipment specially designed to mix asphalt. What we really don’t understand is the gas system of the asphalt mixing station. Only correct maintenance And operation can bring out the best production effect. So what are the faults in the gas circuit of asphalt mixing station?
The following three points are the more common gas path failures of asphalt mixing stations:

In general, the development of my country’s asphalt mixing plant industry is very rapid. In the ton segment, it quickly occupied most of the market share. And with the advancement of technology, it can basically meet the current development needs. However, the total demand for some large-scale asphalt mixing plants has not increased or decreased. What are the reasons?
If we analyze from multiple angles, it is not difficult to find that these reasons are also some of the problems faced by my country’s current asphalt mixing plantindustry. These problems are summarized as follows:

There is also a reversing valve in the asphalt mixing plant, which generally does not cause problems, so I have not understood its solutions in detail before. But in actual use, we encountered this kind of failure. How should we deal with it?
The failure of the reversing valve of the asphalt mixing station is not complicated, that is, the reversing is not timely, gas leakage, electromagnetic pilot valve failure, etc. The corresponding causes and solutions are of course different. For the reversing valve to not change direction in time, it is generally caused by poor lubrication, the spring is stuck or damaged, oil dirt or impurities get stuck in the sliding part, etc. For this, it is necessary to check the status of the lubricator and the quality of the lubricating oil. Viscosity, if necessary, the lubricant or other parts can be replaced.
After long-term use, the reversing valve is prone to wear of the valve core sealing ring, damage to the valve stem and valve seat, resulting in gas leakage in the valve. At this time, the sealing ring, valve stem and valve seat should be replaced, or the reversing valve should be replaced directly. In order to reduce the failure rate of asphalt mixers, maintenance must be strengthened on a daily basis.

The mobile forced asphalt mixing equipment adopts intermittent drying cylinder, double forced mixer, the main machine can be towed, small footprint, short installation cycle, convenient operation and maintenance, good stability, high degree of automation, high degree of standardization, and high quality of finished products, and the technology of continuous improvement. The mobile forced asphalt mixing plant is suitable for high-grade road asphalt paving and maintenance.
1. The combined structure of the drum dryer and the batching machine is installed on a movable bracket for easy movement.
2. The asphalt mixing plant is equipped with a double horizontal shaft to boil the aggregate and ensure uniform mixing.
3. In the densely arranged hanging barrels, the hot aggregate rises vertically. This lifting tool is easy to use and reliable.
4. For accurate weighing of aggregates, asphalt and powder ore, a measuring scale is used, which contains a weighing sensor for electronic measurement.
5. The movement of the power material follows a closed spiral path, which ensures little material loss and provides safe transfer.
6. On the cyclone burner, high-pressure oil is sprayed out and quickly atomized. In the combustion chamber, the material is fed in a spiral manner and automatically ignited by the oil mist, which ensures combustion efficiency. The cylindrical barrel of the burner is separated from the burner head. The furnace cavity can be pushed in and pulled out, which is convenient for replacing the damaged side column bricks inside the burner. The entire burner has a large heat capacity and high thermal strength. This is cost-effectiveness.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing station also needs to be powered on for trial operation before it is officially put into work.
At the beginning of the test run, first run a single motor, and at the same time check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

Asphalt mixing stations play an important role in road construction. This article starts from the site selection, commissioning, and acceptance of the asphalt mixing plant, and elaborates on comprehensive and reasonable planning to avoid disturbing the normal construction order.

If you look at an asphalt mixing plant from a professional perspective, do you know how to judge its work and significance? In fact, the so-called asphalt mixing station is the one that produces asphalt. We can usually see it in road construction projects. Specifically, it mixes some materials that need to be used during the construction process according to certain proportion requirements. Then complete the corresponding construction work.
Then, we can analyze it from a market perspective. Since it was used in the market, it has been widely praised by users. Today’s asphalt mixing plant technology has been greatly improved, and the entire set of equipment used has a variety of advantages. , such as meeting the requirements of stable control, screening, efficient dust removal, excellent mixing, and green environmental protection during the work process. It is even more obvious when used in large-scale projects such as high-grade highways and airports.

Current highway projects are generally large-investment projects. When carrying out actual project construction, it is very necessary to control the cost of the project. The production cost control and management of asphalt mixing stations in highway projects plays a huge role in controlling the cost of the entire highway project, because the main expenses of highway projects are concentrated on the mixing stations, and almost all the equipment used in highway projects Materials are closely related to the mixing station.

Due to raw materials or usage, asphalt mixing plants will be subject to a certain degree of wear or other failures during daily use. If they are not controlled or repaired in time, the problem will be further exacerbated. For asphalt mixing plants, what are the ways to prevent wear and failure?
If the asphalt mixing plant is not treated in time after being worn, it may corrode once it is in contact with air, rainwater, etc. for a long time. If the parts of the asphalt mixing plant are severely corroded, the service life and normal operation of the entire equipment will be affected.

At present, the assembly and installation technology of large-scale asphalt concrete mixing equipment in high-grade highway construction is gradually improving. In order to improve work efficiency, it is necessary to analyze the pretreatment agent for the selection and matching of large-scale mixing equipment and auxiliary equipment, and clarify the installation and commissioning of asphalt stations. With the continuous change of highway construction methods, it is necessary to adopt production equipment according to the requirements of the development of the times. Intermittent asphalt mixing equipment is a widely used road construction equipment with the characteristics of simple operation and high work efficiency. Relevant staff are required to master the installation, construction and management methods of mixing equipment.

In recent years, asphalt concrete, as a new green building material, is gradually being valued by people because of its excellent performance in saving resources, being environmentally friendly, ensuring the quality of construction projects, and achieving sustainable utilization of resources. The development of asphalt concrete fully embodies my country’s policies to achieve energy conservation and emission reduction, and is also an important measure to promote the development of circular economy.

The drive unit is one of the important components of the asphalt mixing plant, so whether it can be reliably operated must be highly valued to avoid adverse effects on the entire asphalt mixing plant. In order to ensure that the drive unit in the asphalt mixing plant is indeed complete and reliable, the following maintenance measures are essential.
The first thing to pay attention to is the universal rotating part of the drive unit of the asphalt mixing plant. This part has always been a fault-prone part. In order to reduce the occurrence of faults, grease should be added on time, and the wear should be checked frequently, and repaired and replaced in time. Users should also prepare the universal shaft assembly to avoid affecting the working process of the entire asphalt mixer.
Secondly, the cleanliness of the hydraulic oil used in the asphalt mixing plant must be ensured. After all, the working environment of the equipment is relatively harsh, so it is necessary to prevent sewage and mud from entering the hydraulic system. The hydraulic oil should also be replaced regularly according to the requirements of the manual. Once water or mud is found mixed in the hydraulic oil during inspection, the hydraulic system should be stopped immediately to clean the hydraulic system and replace the hydraulic oil.
Since there is a hydraulic system, of course, a matching cooling device is also required, which is also an important focus in the drive system of the asphalt mixing plant. To ensure that its function can be fully exerted, on the one hand, the hydraulic oil radiator should be cleaned regularly to prevent the radiator from being blocked by cement; on the other hand, the radiator electric fan should be checked to see if it is running normally to prevent the hydraulic oil temperature from exceeding the standard.
In general, as long as the hydraulic oil of the asphalt mixing plant drive device is kept clean, there are generally few faults; but the service life varies from manufacturer to manufacturer, so pay attention to its alkalinity observation and replace it in real time.

Asphalt mixing plant is a relatively important complete set of equipment in people’s lives. There are many components of this equipment, such as grading machine, vibrating screen, belt feeder, powder conveyor, elevator and other parts. Plug valve is one of them, so what is the specific role of plug valve in asphalt mixing plant? This article will give a brief introduction.
The plug valve is first of all a closure or plunger-shaped rotary valve. Generally, it is necessary to rotate 90 degrees to make the channel opening on the valve plug the same as that on the valve body, or to split it to play the role of opening or closing. The shape of the plug valve in the asphalt mixing plant is generally cylindrical or conical.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixer plant also needs to be powered on for trial operation before it is officially put into work.
At the beginning of the test run, first run a single motor, and at the same time check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

In recent years, asphalt pavement has dominated highway surfaces. With the rapid development of our country’s national economy, highway traffic volume is increasing, axle loads are increasing rapidly, vehicle speeds are increasing, and there are more and more quality problems occurring on asphalt pavements. Some are damaged after repair, and some have a service life of up to Less than design age. This has put forward increasingly higher requirements for the quality of asphalt pavement, and an important factor affecting the performance of asphalt surface layers is the gradation composition of the mixture. This article discusses the mix design of asphalt mixture.

At present, the production efficiency of asphalt mixing plants in my country’s asphalt construction is far lower than the theoretical efficiency at the time of design. The low efficiency of organic waste gas treatment will not only delay the construction process and cause a waste of resources, but also the quality of the construction will not be very good. guarantee. In the construction of asphalt pavement, the main reasons for the low production efficiency of the asphalt plant are insufficient supply of mixture, resulting in loss of continuity of construction, improper equipment parameter settings, excessive overflow and other problems. Effective measures must be taken to deal with these problems, and ultimately improve production efficiency and ensure construction quality.

The asphalt mixing plant contains multiple different systems with different functions. The drying system is one of them. Its main function is to heat and dry the materials to reach the temperature required for the process. In order to successfully achieve this goal, the drying system must provide a certain amount of heat.

When using the asphalt mixing plant, you should regularly check the fuel pressure regulating valve or pressure reducing valve to determine whether the surface of the locking nut on the adjustable bolt is clean and removable; if the surface of the screw or nut is too dirty or rusty, it needs to be repaired or Replace the regulating valve.
Check the oil pump regularly to determine whether the sealing device is intact and whether the internal pressure is stable, and replace any damaged or leaking sealing devices. When using hot oil, check whether all oil pipes are well insulated. The filter installed between the oil tank and the oil pump must be cleaned regularly and checked for excessive wear to ensure that the fuel reaches the oil pump smoothly from the oil tank and to reduce the possibility of potential component failure.

When we operate the asphalt mixing station, we should heat the equipment half an hour in advance, and the clear tank should be heated for at least two hours; and manually operate each part of the equipment to ensure that it is in good operation. status; it is also necessary to conduct relevant inspections on the valves and manually collect and return oil to ensure that the equipment can operate normally.
Several requirements for safe operation of asphalt mixing plants:

Asphalt is commonly used in our modern urban life, especially in the process of urban highway construction. As an important road surface paving material, the demand for its use is relatively high. Only by using better relevant material performance characteristics can the overall effect be well helped.
Asphalt mixing plants are equipment products that need to be involved in the production and use of such products. With its own excellent performance, it has been better expanded in the promotion of the existing market use scope. The coordination of external use factors is also a key part, and the relationship between various factors must be handled well.

Certain failures cannot be avoided during the use of the asphalt mixing plant. For example, a malfunction of the cold material feeding device may cause the asphalt mixing plant to shut down. This may be due to a malfunction in the asphalt mixing plant or due to gravel or foreign matter being trapped under the cold material belt. If it is stuck, if it is a circuit failure, first check whether the motor control inverter of the asphalt mixing station is faulty and whether the line is connected or open.

Asphalt mixing plant, also known as asphalt concrete mixing plant, is a complete set of equipment for batch production of asphalt concrete. Its efficient and stable operation is of great significance to ensure the quality of the project. It is mainly used in the construction of highways, grade roads, municipal roads, airports, ports and other projects. According to the mixing method, asphalt mixing plant can be divided into forced intermittent type and continuous production type; according to the transportation method, it can be divided into fixed type, semi-fixed type and mobile type.
The working principle of asphalt mixing plant mainly includes steps such as aggregate processing, asphalt processing and mixture mixing. Specifically, aggregates (such as gravel, crushed stone, etc.) are sent to aggregate bins through conveyors or bucket elevators, and then measured by aggregate metering devices, and a certain amount of aggregates are sent to sub-bins. Asphalt is stored in asphalt bins or oil storage tanks, and is measured by asphalt metering devices, and a certain amount of asphalt is sent to asphalt sub-bins. Finally, according to the ratio requirements, different aggregates are taken out from their respective sub-bins and sent to the mixture mixer through conveyors or bucket elevators for mixing.

Asphalt mixing plants are highly professional equipment with complex systems. It is inevitable that some failures will occur during use. So, what are the common hardware failures of asphalt mixing plants? Do you know?
(I) Because its system is relatively complex, when different components have problems, the problems caused may be different. If during the operation, it is found that the material addition of each silo is inaccurate, this problem may be due to the failure of the sensor of the asphalt mixing plant. At this time, the machine should be stopped for inspection and replaced with a new sensor if necessary. It may also be caused by the jamming of the scale bar. At this time, foreign objects should be removed in time.

The first step in establishing an asphalt mixing station is to determine the host machine and feed batching system. Generally, the configuration is based on the project’s construction period, total amount of concrete, daily concrete consumption and other indicators. The basic principle is to meet the daily concrete consumption. Under normal circumstances, a project can only have one asphalt mixing station, or separate mixing stations can be set up according to zones, or a large mixing station can be set up together with an appropriate number of concrete transport trucks, all of which depend on the actual situation.