Installation of main equipment of asphalt mixing plant

The actual operation steps of drying drum of asphalt mixing equipment: 1. Pay attention to routine inspection; 2. Proper operation steps; 3. Effective maintenance.
Drying drum is a cylindrical device specially used for heating and drying stones in asphalt mixing equipment. Proper application and maintenance of drying drum can maximize the performance of drying drum, increase its service life and reduce application cost. Let’s take a look at the actual operation steps below.
1. Pay attention to routine inspections
The asphalt mixing equipment drying drum has been tested and inspected before leaving the factory, but it will be subjected to vibration and vibration during transportation to the construction site. A comprehensive inspection should be carried out before use: check whether all anchor bolts are tightened; whether all key pins are properly driven; whether all drive devices are adjusted according to the manufacturer’s instructions; whether all pipe connections are appropriate and whether the three-way joints are reliable; whether the entire equipment is fully lubricated; start the motor and check whether all parts can rotate steadily in the correct rotation direction; whether the pressure gauge can work normally and whether the valve is adjusted to the correct working pressure; whether the burner ignition mechanism is available and whether the gate valve is open.
2. Correct operation steps
After the equipment is started, it is recommended to control the machine manually at the beginning, and then switch to the automatic control mode after achieving the required production volume and pouring temperature. The stone should be dried and have a stable moisture content as much as possible so that the stone can maintain a stable final temperature when passing through the drying drum. If the stones delivered to the drying drum change frequently and the moisture content changes each time, the burner should be adjusted frequently to compensate for these changes.
The stones directly from the crushed stone have a relatively constant moisture content, while the stones from the outdoor storage yard have a higher moisture content, and the moisture content of different piles varies greatly. Therefore, it is best for the stones to come from the same source.

Determining the material is a necessary stage in the design process of asphalt mixing equipment, and it is also one of the most critical links, because the material will be directly related to the use effect and service life of the entire equipment. Generally, when we determine the machine material, we usually base it on the characteristics of the working medium, and the same is certainly true for asphalt mixing equipment.

The quality of asphalt mixture directly determines the quality of asphalt pavement engineering. This article discusses the key points of supervision of ordinary highway asphalt plants in order to better monitor the quality of asphalt mixture.

Asphalt concrete mixing equipment generally uses conveyor belt conveyors to transport cold materials. Its main advantages are large conveying capacity, continuous operation, simple equipment structure and automatic control. However, belt deviation is a common fault, which directly affects the drying operation of the drying drum and also affects the production efficiency of the mixing equipment. Therefore, it is very important for the asphalt mixing station to solve the belt deviation problem at the operation site of the asphalt concrete mixing equipment.

The development prospects of asphalt mixing plants are very good, and the product competition on the market is also very fierce. When the equipment is used, uneven wear of the supporting wheels and wheel rails often occurs, and sometimes there are some abnormal noises and edge gnawing. The main reason is that after the asphalt mixing station has been working for a period of time, the drying cylinder is exposed to high temperature and friction occurs between the supporting wheel and the wheel rail.
Under the action of drying materials in an asphalt mixing station, the equipment will vibrate violently, which will directly lead to improper adjustment of the gap between the wheel rail and the supporting wheel, or mutual interference between the two. The position is skewed, so the operator needs to add grease to the surface contact positions of the supporting wheel and the calibrating wheel rail after every day’s work.

1.During the operation of asphalt mixing station equipment, in addition to ensuring that the asphalt mixing station equipment is in good condition, it should also be equipped with a mineral moisture content detector and a finished material tester, and the relevant data should be frequently tested for the operator to adjust the operation in time, so as to keep the equipment in good condition.
2. In addition to affecting production capacity, the moisture content of mineral materials is also the main factor that determines fuel consumption. Additional material sheds should be added.
3. Before operation, all working parts and devices of the asphalt mixing station equipment should be fully checked to see if they are intact and normal. If there is a problem, it must be properly handled before operation, and it is forbidden to operate with illness.

Many people think that since both asphalt mixing plants and asphalt mixing plants are equipment for producing asphalt, there should be no difference between them, even if there is, it is only in appearance and volume. However, asphalt mixing plants and asphalt mixing plants are different in even their basic structure and function.
First, let me introduce the basic structure of an asphalt mixing plant, which includes five major components: material supply system, metering system, mixing system, and electrical control system. In comparison, the structure of an asphalt mixing plant is simpler, without so many components, so its operation and maintenance will be simpler.

In the 21st century, with the booming development of modern engineering construction, complex integrated supporting equipment has been invested in large quantities. Its complex process and more independent operating components have relatively high requirements for the performance of its equipment control system. The application of PLC in asphalt mixing station realizes the control of the entire process of asphalt mixing station, which facilitates the construction of modern engineering construction. Therefore, this article discusses and analyzes the application of PLC in asphalt mixing station, which has certain economic value and practical significance.

Due to raw materials or usage, asphalt mixing plants will be subject to a certain degree of wear or other failures during daily use. If they are not controlled or repaired in time, the problem will be further exacerbated. For asphalt mixing plants, what are the ways to prevent wear and failure?
If the asphalt mixing plant is not treated in time after being worn, it may corrode once it is in contact with air, rainwater, etc. for a long time. If the parts of the asphalt mixing plant are severely corroded, the service life and normal operation of the entire equipment will be affected.

Asphalt mixing equipment is equipment used to produce asphalt concrete in large quantities. Because this equipment is affected by various factors during the production process, some problems will inevitably occur after a period of use. Sinoroader Group The editor of the asphalt mixing equipment company of China Machinery Co., Ltd. will introduce to you the methods of rescuing damaged parts in asphalt mixing equipment.
Asphalt mixing equipment encounters different problems, and the solutions are also different. For example, one of the common problems of asphalt mixing equipment is that parts are worn out and damaged. The solution that needs to be done at this time is to start from the production of parts. Just start improving.

In order to keep the asphalt mixing plant in a stable operating process, a series of adverse factors related to it must be excluded. What should be paid attention to in this process?
First of all, the selection of the delivery pump in the asphalt mixing plant must meet the requirements of asphalt pouring per unit time during construction, height, and horizontal distance requirements. At the same time, there must be a certain technical and production capacity reserve, and the balanced production capacity is preferably 1.2 to 1.5 times.
Secondly, the movement and hydraulic systems of the asphalt mixing plant must be normal, and there must be no abnormal sound and vibration to avoid large aggregates and lumps inside the equipment, otherwise it is easy to get stuck at the feed inlet of the mixing plant or be blocked due to arching. Another point is that when the asphalt mixing plant is in the same site, it is not suitable to use too many pumps and pumps from multiple manufacturers to avoid affecting its normal operation.

Judging from the situation of highways in our country, asphalt pavement is the most used, which is one of the reasons why asphalt mixing plants have developed so rapidly. Under the situation of rapid economic development, the quality problems of asphalt pavement are gradually increasing, which puts forward higher and higher requirements for the quality of asphalt. It is understood that the primary factor that affects the quality of asphalt is the ratio of raw materials. This is also covered in the introduction of asphalt mixing stations. You can discuss it together.
In order to obtain high-quality asphalt products, in addition to the asphalt mixing equipment meeting the requirements, selecting the appropriate asphalt mixture gradation type is also a top priority. According to my country’s current regulations, the maximum particle size of the asphalt mixture in the upper layer of the highway should not exceed half of the layer thickness; while the maximum particle size of the aggregate in the middle surface layer of asphalt mixture should not exceed two-thirds of the layer thickness; and the asphalt layer should not exceed half of the layer thickness. The maximum nominal aggregate size of the pavement structural layer mixture should not exceed one-third of the layer thickness.
Based on this analysis, if an asphalt surface layer with a certain thickness is selected according to the above specifications, the particle size of the asphalt mixture aggregates will generally be larger, which will inevitably bring insurmountable construction difficulties to the construction of asphalt concrete pavement. After investigation, testing, analysis, and comparison, it can be seen that the lower layer has a wider choice, so the AG-201 gradation type can be used; while the selection of the upper layer mixture type is more difficult, and it is necessary to achieve a reasonable choice of this mix ratio. , on the one hand, we must examine as many aggregate resources as possible, and on the other hand, we must also consider the model of the mixing equipment.
In order to ensure the quality of the project, strict selection and inspection of engineering materials must be carried out. Therefore, the selection and determination of raw materials should be based on the requirements for pavement structure and use quality, combined with the supply of floor materials, and inspection in accordance with the requirements of relevant test procedures, and then Select the best materials so that all technical indicators of the materials meet the specified technical requirements.

With the strengthening of the trend of environmental protection and energy conservation, the environmental protection of asphalt mixing plants has gradually become the mainstream form of mixing plant development. What kind of equipment can be called an environmentally friendly asphalt mixing plant? What are the basic conditions that must be met?
First of all, as an environmentally friendly asphalt mixing plant, it must meet the requirement of using less energy consumption during use. That is to say, under the conditions of the same quantity and quality, less energy is consumed during the operation process, including various resources such as water and electricity.
Secondly, environmentally friendly asphalt mixing plants not only require less energy consumption, but also must achieve higher production efficiency, while also reducing carbon emissions in the entire production process, so as to meet the proposed low-carbon production requirements.

In today’s road construction, the use of a large number of road construction machinery represents the entry into the era of highway mechanization. For users, the goal is to use road construction machinery reasonably and tap its potential as much as possible. However, road construction machinery requires various accessories to work together. Now let’s take the asphalt mixing plant as an example to see what commonly used accessories and equipment are available.
Asphalt mixing plant equipment is a relatively complex system, which includes many equipment, mainly nine parts, namely: bag dust removal, finished material temporary storage warehouse, grading machine, fast heating asphalt tank, asphalt barrel removal machine, asphalt recycled material crushing and screening system, coal block crusher, coal mill and dust removal equipment, etc.

The core of the asphalt mixing plant is its electronic control system. If it has problems, it will cause a lot of trouble to use. However, in actual use, the electronic control system in the asphalt mixing plant will inevitably encounter some problems and failures. How to solve it at this time?
If only the instrument display of the electronic control system of the asphalt mixing plant is inaccurate, it means that the weighing system may be affected by external forces; or the drift error of the sensor causes the weighing zero position or weighing interval to change; it may also be caused by sensor damage.

Mechanism to avoid asphalt damage in asphalt mixing plant
1. Asphalt operators should undergo physical examination. Anyone suffering from conjunctivitis, skin disease or allergic reaction to asphalt should not engage in asphalt work.
2. Asphalt operators must apply protective ointment on exposed parts of their skin, and a first aid kit should be provided on the construction site.
3. The factory uniforms and protective equipment of asphalt operators are stored in a centralized manner and are prohibited from being worn home or entering collective dormitories.
4. The transfer of lumpy asphalt should usually be carried out at night and on cloudy days, especially during hot seasons. Small machinery should be used for loading and unloading, and it should not be lifted and transported directly by hand.

The drying and heating system of the asphalt mixing plant can be regarded as an important part of the whole, so in actual work, it treats the material in a countercurrent heating manner, thereby achieving full dehydration of the cold aggregate, and heating it to a certain temperature, thereby providing the necessary conditions for the normal and continuous operation of the asphalt mixing plant.
During the entire heating process of the asphalt mixing plant, the main purpose is to make the performance of the mixture more in line with the requirements of use, and to make the finished material have good paving performance. Under normal circumstances, the heating temperature of the aggregate is about 160℃-180℃.

Current highway projects are generally large-investment projects. When carrying out actual project construction, it is very necessary to control the cost of the project. The production cost control and management of asphalt mixing stations in highway projects plays a huge role in controlling the cost of the entire highway project, because the main expenses of highway projects are concentrated on the mixing stations, and almost all the equipment used in highway projects Materials are closely related to the mixing station.

Oscillating screen. It can screen the heated aggregate according to the design. It requires fully enclosed, double oscillating motor replacement (replacing one substance for another (mostly the strong one takes the place of the weak)) eccentric shaft oscillation, each The layer screen is easy to install quickly. The service life of the drying roller and the power part is not less than 6000h. The roller can fully use heat, the material curtain flows evenly, and the inclination is required to be adjustable.

Asphalt is commonly used in our modern urban life, especially in the process of urban highway construction. As an important road surface paving material, the demand for its use is relatively high. Only by using better relevant material performance characteristics can the overall effect be well helped.
Asphalt mixing plants are equipment products that need to be involved in the production and use of such products. With its own excellent performance, it has been better expanded in the promotion of the existing market use scope. The coordination of external use factors is also a key part, and the relationship between various factors must be handled well.

Asphalt mixing plants bring a lot of convenience. You should understand what asphalt is. Asphalt is a very viscous liquid with a black surface that dissolves carbon disulfide. They generally exist as asphalt and smoke tar. Asphalt appeared early in social life.

Asphalt damage avoidance mechanism in asphalt mixing plant
1. Asphalt operators should undergo physical examination. Anyone suffering from conjunctivitis, skin disease or allergic reaction to asphalt should not engage in asphalt work.
2. Asphalt operators must apply protective ointment on exposed parts of their skin, and a first aid kit should be provided on the construction site.
3. The factory uniforms and protective equipment of asphalt operators are stored in a centralized manner and are prohibited from being worn home or entering collective dormitories.
4. The transfer of lumpy asphalt should usually be carried out at night and on cloudy days, especially during hot seasons. Small machinery should be used for loading and unloading, and it should not be lifted and transported directly by hand.

Certain failures cannot be avoided during the use of the asphalt mixing plant. For example, a malfunction of the cold material feeding device may cause the asphalt mixing plant to shut down. This may be due to a malfunction in the asphalt mixing plant or due to gravel or foreign matter being trapped under the cold material belt. If it is stuck, if it is a circuit failure, first check whether the motor control inverter of the asphalt mixing station is faulty and whether the line is connected or open.

The plug valve is a rotary valve in the shape of a closure or plunger. After rotating 90 degrees, the channel opening on the valve plug is the same as or separated from the channel opening on the valve body to complete opening or closing. It is widely used in oilfield excavation, transportation and refining equipment, and such valves are also needed in asphalt mixing plants.
The valve plug of the plug valve in the asphalt mixing plant can be cylindrical or conical. In the cylindrical valve plug, the channel is generally rectangular; in the conical valve plug, the channel is trapezoidal. These shapes make the structure of the plug valve light and very suitable for blocking and connecting media and diversion.

Speaking of asphalt mixing plants, we are not unfamiliar with them. This is a unit equipment specially used for asphalt mixing. In fact, what we really lack understanding of is its gas system. Even the accumulated failures that often occur in the gas system of asphalt mixing plants are not very clear. Facts have proved that only by properly maintaining the various systems of the equipment can efficient production and good benefits be achieved.
The following are four types of gas system failures that often occur in asphalt mixing plants. Let’s analyze the causes of the problems behind the failures one by one.

Asphalt mixing plants are large-scale products with high professional and technical requirements, and are composed of multiple systems. Among them, asphalt tanks are also a very critical part. Whether it is manufacturing, debugging or installation, it needs to be operated according to the actual application needs of users.
In addition to the manufacturing, debugging and installation, which need to be operated by installers, the maintenance of asphalt tanks in asphalt mixing plants must also be managed by professionals. At the same time, they must strictly follow all safety rules to operate. Before operation, they must be proficient in the relevant requirements and based on the regulations and safety instructions for storing and handling hot asphalt.

The mixing speed of asphalt mixing plant equipment is indeed very fast, and the corresponding mixing power must be very high, but the specific amount must be measured in a certain way to determine the scope of use of asphalt mixing equipment. There are many methods to measure the mixing power of asphalt mixing equipment, but the relatively small errors are the motor counter-torque measurement method and the strain measurement method.
When the motor of the asphalt mixing equipment starts running, the electromagnetic moment acting on the motor rotor and the electromagnetic moment acting on the motor stator are equal, but their directions are opposite. Therefore, as long as the torque acting on the stator is measured, the torque on the rotor can be obtained, and the actual mixing torque is obtained after deducting the friction torque on the rotor bearing.
On the premise of knowing the torque and mixing speed, the mixing power of the asphalt mixing equipment can be calculated. This is the so-called motor counter-torque measurement method, which is relatively simple and suitable for smaller mixing systems.

Asphalt mixing equipment is also divided into fixed and mobile types. There are still big differences between the two to a certain extent. Let’s take a look at the design of mobile asphalt mixing equipment. What advantages can bring to the equipment?

Safety is the key point for any piece of equipment, and asphalt mixers are of course no exception. What I want to share with you is the knowledge in this area, that is, the safe operation specifications of asphalt mixers. You might as well pay attention to it.

It is inevitable that the asphalt mixing plant will have insufficient pumping force during use. In fact, during the construction process, as long as the asphalt mixing station is operated in accordance with regulations, and the accessories are cleaned and replaced in time, the asphalt mixing plant will generally not have insufficient pumping force. Now the editor of the asphalt mixing station manufacturer briefly introduces the common solutions to insufficient pumping force of asphalt mixing plant as follows.