Introduction to the use of traditional asphalt heating tanks

1 Common diseases of asphalt pavement
There are nine phenomena of early damage to asphalt pavement: rutting, cracks, and potholes. These diseases are the most common and serious, and are one of the common quality problems of highway projects.
1.1 Rutting
Rutting refers to the longitudinal strip grooves on the road surface along the wheel tracks, with a depth of more than 1.5cm. Rutting is a strip groove formed by the accumulation of permanent deformation of the road surface under the repeated action of vehicle load. Rutting reduces the smoothness of the road surface. When the rutting reaches a certain depth, due to the accumulation of water in the rutting, it is easy for cars to slide and cause traffic accidents. The main reasons for rutting are unreasonable design and serious overloading of vehicles.
1.2 Cracks
There are three main forms of cracks: longitudinal cracks, transverse cracks and mesh cracks. When cracks occur in asphalt pavement, water seepage occurs, which harms the surface layer and base layer.
1.3 Potholes
Potholes are common early diseases of asphalt pavement, which refer to the road surface being damaged into potholes with a depth of more than 2cm and an area of ??more than 0.04㎡. The main reason for the formation of potholes is that the oil used in vehicle repair or motor vehicles seeps into the road surface, polluting the asphalt mixture and causing it to loosen. The pits are gradually formed by driving and rolling.

Synchronized gravel sealing is to use special equipment, namely a synchronous gravel sealing truck and bonding materials (modified asphalt or modified emulsified asphalt) to be spread simultaneously on the road surface, and then formed into a single layer through natural traffic rolling or tire roller rolling. A layer of asphalt gravel wearing layer, which is mainly used as the surface layer of the road, and can also be used for the surface layer construction of low-grade highways.

This set of emulsified asphalt production equipment includes water treatment, water storage tanks, water active metering and temperature control systems, asphalt storage tanks, asphalt external temperature systems, hot water pump soap batching systems, soap temporary storage tanks, soap transfer pumps, soap liquid It consists of external temperature system and metering system, filter, hot asphalt transfer pump and metering system, three-stage pipeline emulsifier, emulsified asphalt cooling system and recovery equipment, product tank and electrical automatic control system.
The entire process is modularly designed, and users can freely combine and select according to their needs. The equipment of each part is used as follows: Water treatment system: Mechanical filtration of ordinary tap water absorbs resin exchange reactions, turning high-hardness tap water into pure soft water and reducing water tension. , enhance the emulsification effect of asphalt or modified asphalt.

Synchronous sealing trucks play an important role in road maintenance. Daily maintenance of synchronous sealing trucks is an important part of ensuring the good operation of the equipment and extending its service life. Here are some common maintenance measures:

Analysis of the necessity of emulsified bitumen equipment in modern road construction projects With the acceleration of the construction speed of transportation infrastructure, the construction standards are getting higher and higher, and higher requirements are also put forward for the use of emulsified bitumen in the closed layer of fly ash and the adhesive layer between the new and old ground.

Bitumen decanter equipment can be placed in a complex system as an independent unit, replacing the existing heat source de-barreling method, or in parallel as a core component of a large set of equipment, or it can work independently to meet the requirements of small-scale construction operations.
The Sinoroader bitumen decanter device is mainly composed of a de-barreling box, a lifting mechanism, a hydraulic thruster and an electrical control system. The box is divided into two chambers, the upper chamber is a barreled bitumen melting chamber, and heating coils are evenly distributed around it. The heating pipe and the bitumen barrel mainly exchange heat in a radiation manner to achieve the purpose of bitumen de-barreling. Several guide rails are the tracks for the bitumen barrel to enter. The lower chamber is mainly to continue heating the bitumen removed from the barrel to make the temperature reach the suction pump temperature (100℃), and then the asphalt pump is pumped into the upper chamber. At the same time, an empty barrel is pushed out at the rear end outlet. There is also an oil tank on the platform at the entrance of the asphalt barrel to prevent the dripping bitumen from flowing out.
The inlet and outlet doors of the device adopt a spring automatic closing mechanism. The door can be automatically closed after the asphalt barrel is pushed in or out to reduce heat loss. A temperature gauge is installed at the asphalt outlet to observe the asphalt outlet temperature. The electrical control system can control the opening and closing of the hydraulic pump and the reversing of the electromagnetic reversing valve to realize the advance and retreat of the hydraulic cylinder. If the heating time is extended, a higher temperature can be obtained. The lifting mechanism adopts a cantilever structure. The bitumen barrel is lifted by an electric hoist, and then moved horizontally to place the bitumen barrel on the guide rail. A temperature gauge is installed at the outlet of the asphalt meltering equipment to observe its outlet temperature.

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

In addition to being used according to regulations, modified bitumen equipment should also be maintained regularly in order to effectively extend the service life of modified bitumen equipment. The delivery pump of modified bitumen equipment, as well as its motor and reducer, need to be maintained in accordance with the specifications of the instructions. If the modified bitumen equipment is parked for a long time, the liquid in the tank and pipeline needs to be drained, and each moving component also needs to be filled with grease. The dust in the control box of the modified bitumen equipment needs to be cleaned once every six months. A dust blower can be used to remove dust to prevent dust from entering the machine and damaging parts. The micro powder machine needs to add unsalted butter once for every 100 tons of emulsified bitumen produced.

Asphalt used to pave roads. It can be obtained by regular vacuum distillation of crude oil with appropriate properties, and can also be obtained by shallow oxidation of vacuum residue or propane deasphalting process. It can also be prepared by mixing asphalt of different duction and injection degree

Technical features of fiber sealing equipment:
1. Zero starting strong injection technology
With more than ten years of manufacturing history of asphalt spreading trucks and asphalt gravel synchronous sealing trucks, the zero-start strong spraying technology has been accumulated for many years. The combination of time-reliable hydraulic transmission components and Meitong’s control system can make the equipment instantly start from zero. Spraying starts in line, stable and reliable.
2. Duplex sealing structure
The sealing process of this equipment is a three-layer simultaneous and continuous construction process of one layer of asphalt + one layer of fiber + one layer of asphalt, forming a layer of interactive dense network winding structure, which fully meets the user’s construction requirements.

Asphalt sealant is a material specially used for road crack repair. The following is a detailed introduction to asphalt sealant:
1. Definition and composition
Asphalt sealant is a road repair material made of asphalt or modified asphalt as the base material, with a certain amount of additives and fillers added, and processed by special technology. It usually has a black or dark brown appearance and is in a solid or semi-solid form.
2. Main characteristics
High adhesion: Asphalt sealant can firmly bond to the crack wall of the road surface to form a tight sealing layer to prevent moisture and other harmful substances from invading the road surface structure.
High elasticity: It has a certain elastic recovery ability and can adapt to the expansion and contraction changes of the road surface to prevent further expansion of cracks.
Weather resistance: After special process treatment, it has good weather resistance and can maintain its stable performance for a long time.
Convenient construction: The construction operation is simple and fast, without complex construction machinery, which reduces the construction cost.
3. Scope of application
Asphalt sealant is widely used in crack repair of various asphalt pavements, including highways, urban roads, airport runways, etc. At the same time, it can also be used for the maintenance and repair of asphalt surfaces such as bridges, tunnels, and parking lots.

The requirements for SBS asphalt emulsification equipment are very high. The micro powder machine must have a sufficiently large driving force and can bear the condensation type. Because the temperature requirements of the emulsion SBS asphalt process are relatively high, the emulsified asphalt should be passed through a heat exchanger before feeding to reduce the emulsified asphalt temperature to below 90°C to prevent the emulsified asphalt from breaking due to excessive temperature.
The application scope of SBS modified emulsified asphalt is very wide. According to the nature of the construction, it can be used in new construction, renovation, and reconstruction projects; according to the nature of the project, it can be used in overhaul, equipment overhaul, and maintenance projects. Among them, the actual application projects include micro-surfacing, cold regeneration, cold mixing and cold paving, adhesive layer, permeable oil, slurry seal, gravel permeable layer, fog permeable layer, road moisture-proofing, SBS membrane, ground seam filling, and all other projects that can use emulsified asphalt.

Asphalt spreader is an irreplaceable tool for highway maintenance. Asphalt spreader is an irreplaceable tool for highway maintenance. Highway maintenance is divided into four categories according to the nature of the project, scale, and technical complexity: minor repair, medium repair, major repair, and improvement. Specific classification:
(1) Minor repair and maintenance project: preventive maintenance and repair of slightly damaged parts of the highway and all its engineering facilities to keep them in good condition. It is usually planned and carried out daily by the maintenance team within the annual minor repair and maintenance quota funds on a monthly (ten-day) basis.
(2) Medium repair project: regular repair and reinforcement of general wear and tear and local damage of highway engineering facilities to restore them to their original state. It is usually planned and implemented by grassroots road maintenance agencies on an annual (seasonal) basis.
(3) Major repair project: periodic comprehensive repair of major damage to highway facilities to fully restore them to the original design standards, or local improvements and individual additions within the original technical level to gradually improve the highway’s traffic capacity. It is usually organized and implemented by grassroots road maintenance agencies or with the help of their superior agencies according to the approved annual project budget.
(4) Improvement projects are large projects that improve the technical level of roads and their engineering facilities in stages and sections due to their inability to meet traffic volume and load requirements, or significantly improve traffic capacity through improvements. It is usually organized and implemented or completed through bidding by regional road maintenance agencies or provincial road maintenance agencies according to the approved plan and design budget. As a manufacturer of asphalt spreaders, we welcome you to visit us.

During the use of emulsified bitumen equipments, if maintenance is not paid attention to, the cycle will be short, and problems will often occur during use. Only by doing a good job of maintenance can the operation efficiency of the equipment be improved. For example, during maintenance, the following points must be grasped.
It is necessary to regularly check the wear condition of the internal structural components of the mechanical equipment, such as the core feed pipe, the rough jaw plate on the impeller, the cone cap, the wear level of the jaw plate, the rain shield on the circle, and the wear condition. If the wear is more serious, it is necessary to replace or repair it in time. When replacing, it is also necessary to pay attention to the model and specifications, and replace it according to the original components as a reference.

Colored asphalt pavement is a kind of special pavement material that mixes colored particles into asphalt and then lays on the pavement

In our daily life, we can often see emulsified asphalt equipment. Its appearance has brought us great convenience. So what is the difference between its modification process? Below, the editor will give you a brief introduction to the relevant knowledge points.
1. Emulsified asphalt equipment first emulsifies and then modifies: This is a relatively simple way to make modified emulsified asphalt. The production process is to grind hot asphalt and emulsifier soap together through a colloid mill to make ordinary emulsified asphalt, and then add latex-like modifiers to the emulsified asphalt through mechanical stirring to make modified emulsified asphalt. The characteristic of this method is that it does not require high equipment.

Friends who are ready to get started have a surprise today. The editor will give you a brief introduction on how to produce emulsified asphalt.

In the cold winter, the following points should be noted when using bitumen melter equipment:

1. Keep warm: The bitumen melter equipment needs to be operated indoors or in a place with sunshade facilities, and ensure that the temperature of the bitumen melter and the surrounding environment is kept within an appropriate range.
2. Check the bitumen melting equipment: Before use, the bitumen melter should be checked, including whether the circuit, liquid circuit and other parts of the equipment are working properly, and whether the equipment has leakage, water leakage and other conditions.
3. Pay attention to safety: During operation, protective bitumen melter equipment should be worn to avoid direct contact with hot bitumen. At the same time, avoid overloading the bitumen melter to prevent equipment damage and safety accidents.
4. Control speed: Reasonably control the working speed of the bitumen melting equipment according to weather conditions and road conditions to avoid overheating of the equipment, which may cause the bitumen to flow too quickly or burn.
5. Storage conditions: When not in use, place the equipment in a dry, ventilated and moderately warm place, and ensure that the residue in the equipment is completely cleaned.

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

Maintenance points of asphalt spreading trucks in different working hours
per month (or every 200 hours worked)；
​Per year (or every 500 hours worked)；
Every two years (or every 1,000 hours worked)；

Asphalt melting equipment follows the continuous development of urbanization. Whether in rural areas or in big cities, you can see a lot of construction sites, among which it is inevitable that asphalt melting equipment is set up nearby. Asphalt melting equipment manufacturers, whether large or small asphalt melting equipment or relatively large and small, although it is just a simple mechanical equipment, but to move or transport it, it is a small matter, and there are many places that require attention.
The technical level of the asphalt melting equipment disassembly and assembly team directly affects the disassembly and assembly progress of the asphalt melting equipment; improve on-site supervision, reasonably organize disassembly and assembly machinery and equipment and workers, try to avoid cross-operation, and promote the disassembly and assembly process to consume less manpower and machinery shifts to do a good job in the transportation of asphalt melting equipment; ensure that the asphalt melting equipment is not damaged and the prefabricated components are not missed.

Contemporary roads and pavements have undergone many changes: traffic volume and driving frequency have increased significantly, the axle load of logistics trucks has continued to increase, one-way driving in separate lanes has been widely implemented, and regulations have further improved the anti-flow resistance of the ground, that is, the work of modified asphalt equipment under high temperatures ability;

Water is one of the raw materials of the modified asphalt storage tank, and it is distributed in various components of the modified asphalt storage tank equipment. According to the components where water is distributed, the anti-cold measures are explained one by one. The water tank of the modified asphalt storage tank, the water inside the water tank is released through the filter valve. Some instruments of the modified asphalt storage tank do not have a filter valve to save the cost of the equipment. The modified asphalt storage tank can only be drained by loosening the flange bolts at the bottom. The water pump of the modified asphalt storage tank mentioned here includes a hot water pump and a circulating water pump. This type of water pump for the modified asphalt storage tank generally uses a pipeline centrifugal pump. There is a sewage outlet at the bottom of the pipeline centrifugal pump. The modified asphalt storage tank pays attention to the sewage treatment of the sewage outlet at the bottom of the pump. The modified asphalt storage tank emulsion tank generally uses a cone bottom. However, in order to better process the modified asphalt storage tank coefficient, the inlet and outlet are usually not placed at the bottom of the modified asphalt storage tank. Emulsion (mostly water) will remain at the bottom of the tank, and this part of the residual liquid in the modified asphalt storage tank must be discharged through the filter valve at the bottom. Emulsion pump for modified asphalt storage tank There are basically two types of emulsion pumps for modified asphalt storage tank equipment on the market, gear pumps or centrifugal water pumps. Gear pumps can only discharge the liquid inside the pump through the connection flange of the pipeline. The centrifugal water pump for modified asphalt storage tanks uses its own sewage outlet for sewage treatment. The first four items of modified asphalt storage tanks with basic knowledge are basically discharged, and the modified asphalt storage tanks will focus on the latter types. Modified asphalt storage tank colloid mill There will also be residual emulsion or water inside the modified asphalt storage tank colloid mill. The gap between the stator and rotor of the colloid mill is within 1mm. If there is a little residual water in the modified asphalt storage tank, it will cause the accident of frozen modified asphalt storage tank. The residue in the colloid mill can be treated by loosening the connection bolts of the finished product pipeline.

There is a wide variety of asphalt melting equipment on the market, including different brands and models. The prices of these devices vary widely, depending mainly on factors such as their features, performance, and specifications.
Asphalt melter equipment produced by some large brands such as Sinoroader usually has higher quality and reliability, so the price is relatively higher. However, they also offer longer service life and better maintenance support.

Emulsified asphalt (ingredients: asphaltene and resin) heating tank is a new type of equipment for heating emulsified asphalt. Its appearance replaces the traditional thermal oil heating equipment, which brings great convenience to our users and improves work efficiency. Then let’s take a detailed look at how it is better than the traditional thermal oil heating equipment.
Emulsified asphalt (ingredients: asphaltene and resin) heating tank is another new type of emulsified asphalt heating storage equipment developed by technically separating the characteristics of traditional thermal oil heating emulsified asphalt tanks and internal heat part (part) rapid emulsified asphalt heating tanks. The automatic circulation program of the asphalt heating equipment enables the asphalt to automatically enter the heater, dust collector, induced draft fan, asphalt pump, asphalt temperature display, water level display, and steam generator as required.
It consists of pipeline and asphalt pump preheating system, pressure relief system steam combustion system, tank cleaning system, oil unloading tank installation, etc. All are installed on the tank body (inside) to form a compact integrated structure. It fully compensates for the shortcomings of traditional thermal oil heating equipment, such as long heating time and high energy consumption.

All kinds of base layers have the problem of strength formation and growth (Emerson). The strength is gradually generated during the curing process, and the internal structure will become more and more dense. The test shows that when the semi-rigid base layer is sprayed with penetration oil before the cement (material: powdered water-hardening inorganic cementitious material) has not yet hardened, the penetration depth is deep; with the increase of age and strength, the penetration effect of the penetration oil is getting worse and worse.
At the same time, timely spreading of penetration oil has a good retention effect on the moisture in the base layer, preventing the evaporation of moisture, ensuring the formation of the strength of the base layer, and the surface of the base layer is not easy to loosen. The penetration oil also protects the semi-rigid base layer from cracking due to exposure to the sun. Furthermore, since the base layer is no longer covered and watered for curing, the temperature inside the base layer is high, which is conducive to the growth of strength.

Emulsified asphalt equipment is a special equipment for producing emulsified asphalt. The emulsified asphalt produced by emulsified asphalt equipment is used in many industries. I wonder how much you know about the emulsified asphalt produced by emulsified asphalt equipment. Let’s take a look at them one by one:
Slurry seal is a cold mix asphalt mixture with the advantages of aggregate and asphalt mixing. Under normal circumstances, similar graded slurry seal has a higher modulus than hot mix asphalt mixture, so it is often used to fill road rutting. The higher stability has a higher resistance to deformation. The mixture is usually composed of harder fine aggregate grading and wear-resistant aggregate with high sand equivalent, especially micro-seal and polymer-modified seal. This greatly increases the strength and integrity of the road surface. This makes the road surface have high wear resistance and excellent deformation resistance. Emulsified asphalt emulsion is also easy to use on a mobile slurry seal paver, where mixing and admixtures are used for chemical control to meet maintenance needs.

What key points should be paid attention to when feeding emulsified asphalt equipment? When it comes to emulsified asphalt equipment, I don’t know how much you know about it? What should you pay attention to when adding materials?
The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) Open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.