Manufacturers share what should be paid attention to when using asphalt melting equipment?

Synchronous sealing trucks play an important role in road maintenance. Daily maintenance of synchronous sealing trucks is an important part of ensuring the good operation of the equipment and extending its service life. Here are some common maintenance measures:

1 Common diseases of asphalt pavement
There are nine phenomena of early damage to asphalt pavement: rutting, cracks, and potholes. These diseases are the most common and serious, and are one of the common quality problems of highway projects.
1.1 Rutting
Rutting refers to the longitudinal strip grooves on the road surface along the wheel tracks, with a depth of more than 1.5cm. Rutting is a strip groove formed by the accumulation of permanent deformation of the road surface under the repeated action of vehicle load. Rutting reduces the smoothness of the road surface. When the rutting reaches a certain depth, due to the accumulation of water in the rutting, it is easy for cars to slide and cause traffic accidents. The main reasons for rutting are unreasonable design and serious overloading of vehicles.
1.2 Cracks
There are three main forms of cracks: longitudinal cracks, transverse cracks and mesh cracks. When cracks occur in asphalt pavement, water seepage occurs, which harms the surface layer and base layer.
1.3 Potholes
Potholes are common early diseases of asphalt pavement, which refer to the road surface being damaged into potholes with a depth of more than 2cm and an area of ??more than 0.04㎡. The main reason for the formation of potholes is that the oil used in vehicle repair or motor vehicles seeps into the road surface, polluting the asphalt mixture and causing it to loosen. The pits are gradually formed by driving and rolling.

The engine is the source of power for the vehicle. If the synchronous sealing vehicle wants to perform normal construction operations, it must ensure that the engine is in good condition. Routine maintenance is an important means to effectively prevent engine failure. How to maintain it is determined by Xinxiang Junhua Special Vehicle Vehicles Co., Ltd. will take everyone to understand.

Microsurfacing is a thin layer of overlay placed on old asphalt pavement and is a type of preventive maintenance process. The purpose of microsurfacing is road maintenance. After micro-surface paving, it can repair cracks in the original road surface, waterproof and beautify the road surface.
The construction method of micro surfacing is: using a micro surfacing paver to evenly spread modified emulsified asphalt, a certain grade of mineral materials, water and other additives on the road surface in a certain proportion.

Asphalt mixture is a kind of composite material, mainly composed of asphalt, coarse aggregate, fine aggregate, mineral powder, some also added polymer and wood cellulose; By these different quality and quantity of materials mixed to form different structures, and have different mechanical properties

Everyone has a side of themselves that they don’t want others to know. As a preventive road maintenance technology, slurry sealing has some shortcomings. do you think so?
Slurry seal is a kind of road protection that uses special equipment to mix emulsified asphalt, water, additives, aggregates, fillers and other ingredients in a certain proportion, and then mixes the slurry mixture onto the original road surface to form a thin layer. Maintenance technology. These are all well known. The editor will not go into details on this.

For each equipment used, certain safety knowledge must be followed. For the use of emulsified asphalt equipment, detailed instructions are given:
1. Placement: The emulsified asphalt equipment should be placed on a flat place, the front axle should be fixed to the sleepers, and the tires should be dangling. The machine should not be fiddled with at will to affect normal operation.
2. Regularly check whether the mixer blades are deformed and the screws are loose.
3. Check whether the running direction of the mixing drum is consistent with the direction of the arrow. Please replace the positive and negative poles of the terminal.
4. Before turning on the power, check the no-load test run, check for air leakage, and check the idling speed of the mixing barrel. The normal speed is about 3 times faster than the empty car. If not, stop the inspection.
5. If the asphalt material is stopped for one hour after mixing, clean the mixing barrel, pour in clean water, and clean the mortar. Then drain the water. Remember that there should be no water in the barrel to prevent the formula from changing, so that the page and other links will rust. Sinoroader will provide you with more safe emulsified asphalt knowledge, please continue to browse.

What details should be paid attention to when adding materials to the emulsified bitumen equipment? Speaking of emulsified bitumen equipment, I don’t know how much you know? What should we pay attention to when adding materials?
The black anti-static tweezers grinding wheel of the emulsified bitumen equipment has no heating barrel. Before use, you must first add an appropriate amount of diesel, let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is about 80 to 100 degrees) Open the shut-off valve on the oil pipe and discharge the diesel in the machine. The temperature of the black anti-static tweezers grinding wheel is about 80 to 100 degrees before it can be loaded and put into production. If there is a heating collet, heat the grinding wheel before starting, and then load the materials for production.

The heating principle of asphalt decanter equipment is to heat, melt and decanter the asphalt through the heating plate. It is mainly composed of de-barreling box, lifting system, propeller and electrical control system.
The box of asphalt decanter plant is divided into upper and lower chambers. The upper chamber is the asphalt melting chamber, which is densely covered with heat transfer oil heating coils or hot air heating pipes. The asphalt is melted and removed from the barrel by heat. The hoisting hook is installed on the gantry, and a barrel grabber is hung. The asphalt barrel is lifted by the electric winch, and then the asphalt barrel is placed on the guide rail by horizontal movement. Then the propeller pushes the barrel into the upper chamber through two guide rails, and an empty barrel is pushed out at the rear end outlet.
An anti-drip oil tank is provided at the entrance of the asphalt barrel. The asphalt enters the lower chamber of the box and is continuously heated to a temperature of about 100 to be transported, and then pumped into the asphalt tank by the asphalt pump. The lower chamber can also be used as an asphalt heating tank.
The asphalt decanter plant has the characteristics of not being restricted by the construction environment, strong adaptability and extremely low failure rate. If large production is required, multiple units can be assembled.

There are certain standards for the composition and mix ratio of micro-surfacing, and a wide range of materials are used, including polymer-modified emulsified asphalt, various aggregates, cement, water, additives, etc. Raw material quality has a significant impact on microsurfacing performance, so understanding the performance of each component and the key factors that influence its performance is critical to ensuring the quality of your microsurfacing mix.

Regarding the basic knowledge of modified bitumen plant, I believe that many consumers have already had a basic understanding of it. Because of the continuous development of various fields today, various facilities including modified bitumen plants have been well developed and applied, and modified bitumen plant has gradually been recognized by customers.
The direct quick heating portable equipment in the modified bitumen equipment not only has a faster heating speed, saves fuel, and is pollution-free, but also convenient and easy to operate. The automatic heating system completely eliminates the trouble of baking or cleaning bitumen and pipelines.

Friends who are ready to get started have a surprise today. The editor will give you a brief introduction on how to produce emulsified asphalt.

There are many types of emulsified bitumen, and PC-2 is one of them, which is a spray-type emulsified bitumen. It is used for spraying oil through the base layer of granular materials and health care spraying on semi-rigid base layers. There is also the PA-2 type, which has the same purpose as the PC-2 type. The difference is that the PC-2 type is a cation, while the PA-2 type is an anion.

How to reduce energy consumption of emulsified asphalt machinery is a concern of many users and many manufacturers. Therefore, today, Sinosun Company, as a manufacturer of emulsified asphalt equipment, would like to take this opportunity to share with you the method of reducing energy consumption of emulsified asphalt machinery.
Since emulsified asphalt appears as a finished product in emulsified asphalt machinery, and the outlet temperature of ordinary emulsified asphalt is about 85℃, and the outlet temperature of emulsified modified asphalt is above 95℃, there is a lot of latent heat in emulsified asphalt, but the emulsified asphalt equipment does not make good use of them, but directly enters the finished product tank, allowing heat to be lost at will, resulting in energy waste.

The selection of asphalt melting equipment should take into account factors such as the use environment, working conditions, and technical requirements. Common ones include hot oil heating equipment, electric heating equipment, and gas heating equipment.
Hot oil heating equipment is suitable for occasions that require long-term heating and high temperature control accuracy;
Electric heating equipment is suitable for small projects or occasions where temperature control accuracy is not required;
Gas heating equipment has the advantages of simple operation and low cost, but safety protection measures must be strictly followed.
When choosing, it is also necessary to comprehensively consider factors such as economy and environmental protection.

Asphalt melting equipment is an important road construction tool used to heat asphalt to the appropriate temperature for construction. It can provide reliable solutions and make road construction more convenient. The working principle of this equipment is to heat the asphalt to the appropriate temperature through a heater, and then transport the hot asphalt to the construction site through a conveying system.

Road repair Keep the road to maintain the performance of the road, restore the damaged part in time, ensure the safety, comfort and smooth driving, save transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time. With the performance, the damaged part is restored in time to ensure the safety, comfort and smooth driving, saving transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time.

1. Observation: Pay attention to the dynamics of the road surface after milling (three to four days), and pave the milled and roughened road surface in time when paving conditions are met.
2. On-site mixing: During construction and production, a sealing slurry truck should be used for on-site mixing. Through the metering equipment of the sealing truck and on-site operation by a robot, it is ensured that emulsified asphalt, water, mineral materials, fillers, etc. can be mixed according to a certain proportion. , stir through the mixing box, and the paving thickness is not higher than the roughing depth.

Fog seal is an asphalt pavement maintenance construction method.
When the asphalt pavement has increased water permeability, loss of fine aggregate, cracks, pitting, etc., a fog seal layer can be used for pavement repair. The bonding material of the fog seal layer is fluid, can repair cracks and gaps, and can heal cracks below 0.3. After construction, the oil content of the road surface is increased, the anti-sticking aggregate is loosened, and it can play a waterproof role.
Before construction, the original road surface should be surveyed and analyzed to determine the construction bonding materials and spray volume.
So what precautions should be taken during construction?

Modified bitumen equipment uses modified bitumen colloid mill. Its blade has high hardness, high linear speed of the moving disk, and the gap can be adjusted to 0.15mm. It is suitable for processing various polymer-modified bitumens, such as SBS, PE, EVA, etc.

Synchronous chip seal is a process technology for treating cracks in asphalt pavement, and it is currently a highway construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical characteristics are? If you don’t know, follow the editor of Sinoroader company to have a look.

I believe that many people already know about synchronous gravel sealing. But when asked under what circumstances synchronous gravel sealing is suitable, many people cannot tell.
Under what circumstances is synchronous gravel sealing more suitable? According to the technical specifications for the construction of simultaneous gravel sealing, simultaneous gravel sealing can be used for the following disease types:

Recently, I found that many people don’t know much about the operation skills of asphalt pavement spreaders. If you also want to know what’s going on, you can read this introduction below.
Asphalt pavement spreaders are an indispensable and important equipment in road maintenance and construction. Their operation skills directly affect construction efficiency and project quality. The following introduces the operation skills of asphalt pavement spreaders from four aspects: pre-operation preparation, precautions during construction, spreading skills, and post-operation cleaning and maintenance:

Emulsified asphalt can be spread by mechanical spreading and manual spreading. Different spreading methods will have different effects on pavement performance, so it is very important to choose the right spreading method. At the same time, maintenance and management after spreading are equally important to ensure the safety and durability of the pavement.
Emulsified asphalt is a common pavement material that is widely used in road construction and maintenance. There are two main ways to spread emulsified asphalt: mechanical spreading and manual spreading. Mechanical spreading generally uses a special spreading vehicle that can quickly and evenly spread emulsified asphalt. Manual spreading is carried out by workers using tools such as brushes or rollers, which is suitable for pavement treatment in small areas or special areas.
Different spreading methods also have different effects on pavement performance. Mechanical spreading can quickly complete large-area treatment and spread evenly, which is conducive to ensuring the flatness and anti-skid properties of the pavement. Manual spreading can more finely treat special areas such as shoulders and intersections to improve the overall performance of the pavement.

In the cold winter, the following points should be noted when using bitumen melter equipment:

1. Keep warm: The bitumen melter equipment needs to be operated indoors or in a place with sunshade facilities, and ensure that the temperature of the bitumen melter and the surrounding environment is kept within an appropriate range.
2. Check the bitumen melting equipment: Before use, the bitumen melter should be checked, including whether the circuit, liquid circuit and other parts of the equipment are working properly, and whether the equipment has leakage, water leakage and other conditions.
3. Pay attention to safety: During operation, protective bitumen melter equipment should be worn to avoid direct contact with hot bitumen. At the same time, avoid overloading the bitumen melter to prevent equipment damage and safety accidents.
4. Control speed: Reasonably control the working speed of the bitumen melting equipment according to weather conditions and road conditions to avoid overheating of the equipment, which may cause the bitumen to flow too quickly or burn.
5. Storage conditions: When not in use, place the equipment in a dry, ventilated and moderately warm place, and ensure that the residue in the equipment is completely cleaned.

As we all know, emulsified bitumen is a single-component black viscous liquid that can combine the roadbed and the pavement to improve the performance and service life of the road. So what problems should be paid attention to when using emulsified bitumen? Let’s follow the editor of Sinoroader Group, an emulsified bitumen manufacturer, to learn about it.

As a manufacturer with many years of experience in emulsified bitumen construction, Sinoroader Group believes that everyone needs to pay attention to the following 2 points when using it:

Modified (rubber powder) bitumen equipment, one of the road maintenance equipment. It is a kind of equipment that measures, mixes and develops SBS, rubber powder and asphalt.
Modified (rubber powder) bitumen equipment is a set of wet modification processing technology, which mainly consists of modified material metering and promotion, bitumen rapid heating, asphalt metering, high-intensity mixing tank, mixed material transfer pump, development tank, colloid mill, Control system and other components.

For users of equipment, the amount of material used is the focus of every user. We should attach great importance to this link in the production process. The following is an analysis of the amount of emulsifier used by Gaoyuan manufacturers.
When emulsified asphalt equipment is emulsifying asphalt, the asphalt temperature is better controlled at above 130°C to have better fluidity; 2. The amount of emulsifier is generally 8-14‰ of emulsified asphalt, that is, 8-14kg per ton of emulsified asphalt (asphalt content is more than 50%), and the temperature is 60-70°C. The emulsifier should be used in the middle and upper limit of the production, 10 kg per ton of emulsified asphalt, or 20 kg per ton of water (asphalt content is 50%); the amount of BE-3 emulsifier is generally 18-25‰ of emulsified asphalt, that is, 18-25kg per ton of emulsified asphalt (asphalt content is more than 50%), and the emulsifier solution temperature is 60-70°C. The emulsifier should be used in the upper and middle limits in the first production to ensure successful production. Use 24 kg per ton of emulsified asphalt, or 48 kg per ton of water (asphalt content is 50%). After the production goes smoothly, the dosage can be reduced according to actual conditions.

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.