modified bitumen plant

There are many types of bitumen emulsifiers, and there are many classification methods. For specific classifications, please refer to previous articles. The raw materials required for the production of emulsion bitumen are: bitumen, water and bitumen emulsifier. High-standard emulsion bitumen requires adding additives and adjusting acid. According to whether acid adjustment is needed in the emulsion bitumen production process, it can be divided into two categories: emulsion bitumen that requires acid adjustment and emulsion bitumen that does not require acid adjustment.

There are many types of emulsified asphalt (composition: asphaltene and resin) equipment. Emulsified asphalt (composition: asphaltene and resin) equipment can be divided into intermittent operation type, semi-continuous operation type, and Continuing the three operating types, what is the knowledge about different types of emulsified asphalt equipment?

Bitumen emulsifier is a surfactant. A surfactant is a compound that reduces the surface tension between two liquids, a gas and a liquid, or a solid and a liquid. Surfactants are mainly used in: detergents, detergents, fabric softeners, wetting agents, emulsifiers, foaming agents, dispersants, adhesives, etc.

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

With the rapid development of highway construction and the increase in demand for asphalt, barreled bitumen has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported bitumen used in high-grade highways is in barrel form, which requires an bitumen melter equipment with fast melting speed, clean debarreling, and prevention of asphalt aging.
The upper part of the debarreler of the bitumen melter equipment is hotter, and each barrel is directly heated by the heat transfer oil coil. The barrel wall directly bears the heat radiation of the heating coil. The asphalt is cleanly and sensitively debarreled, and there will be no waste of asphalt hanging barrels. According to the principle of layered heating, four-layer heating technology is adopted, with single inlet and single outlet of heat transfer oil, and high thermal efficiency of heating; at the same time, the waste heat of combustion exhaust gas is used for secondary heating, and power is effectively used; the debarreler body is insulated with high-quality rock wool material. It is suitable for various types of imported and domestic barrels, and the deformation of asphalt barrels will not affect production.

Emulsified asphalt can be spread by mechanical spreading and manual spreading. Different spreading methods will have different effects on pavement performance, so it is very important to choose the right spreading method. At the same time, maintenance and management after spreading are equally important to ensure the safety and durability of the pavement.
Emulsified asphalt is a common pavement material that is widely used in road construction and maintenance. There are two main ways to spread emulsified asphalt: mechanical spreading and manual spreading. Mechanical spreading generally uses a special spreading vehicle that can quickly and evenly spread emulsified asphalt. Manual spreading is carried out by workers using tools such as brushes or rollers, which is suitable for pavement treatment in small areas or special areas.
Different spreading methods also have different effects on pavement performance. Mechanical spreading can quickly complete large-area treatment and spread evenly, which is conducive to ensuring the flatness and anti-skid properties of the pavement. Manual spreading can more finely treat special areas such as shoulders and intersections to improve the overall performance of the pavement.

Asphalt mixture mixing equipment is a factory-style complete set of equipment that mixes dry and heated aggregates of different particle sizes, fillers and asphalt according to the designed mix ratio at a specified temperature into a uniform mixture. It is widely used in high-grade highways and urban roads. , airports, docks, parking lots and other engineering construction. It is a key equipment for asphalt pavement construction, and its performance directly affects the quality of asphalt pavement.
Generally, there are two types of asphalt concrete mixing equipment: intermittent type and continuous type. The continuous process flow is simple and the equipment is simplified. As for the intermittent forced mixing equipment, due to the secondary screening of aggregates, various components are measured in batches, and forced stirring and mixing can reliably ensure gradation, and the measurement of powder and asphalt can also achieve very high accuracy; so the mixing equipment The asphalt mixture produced is of high quality and can meet various construction requirements.

Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreading truck, check the four thermal oil valves and air pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Try running the asphalt pump and cycle for 5 minutes. If the pump head shell is hot to your hands, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not rotate or make noise. You need to open the valve and continue to heat the asphalt pump until it can operate normally.

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

Asphalt sealant is a material specially used for road crack repair. The following is a detailed introduction to asphalt sealant:
1. Definition and composition
Asphalt sealant is a road repair material made of asphalt or modified asphalt as the base material, with a certain amount of additives and fillers added, and processed by special technology. It usually has a black or dark brown appearance and is in a solid or semi-solid form.
2. Main characteristics
High adhesion: Asphalt sealant can firmly bond to the crack wall of the road surface to form a tight sealing layer to prevent moisture and other harmful substances from invading the road surface structure.
High elasticity: It has a certain elastic recovery ability and can adapt to the expansion and contraction changes of the road surface to prevent further expansion of cracks.
Weather resistance: After special process treatment, it has good weather resistance and can maintain its stable performance for a long time.
Convenient construction: The construction operation is simple and fast, without complex construction machinery, which reduces the construction cost.
3. Scope of application
Asphalt sealant is widely used in crack repair of various asphalt pavements, including highways, urban roads, airport runways, etc. At the same time, it can also be used for the maintenance and repair of asphalt surfaces such as bridges, tunnels, and parking lots.

The emulsified bitumen equipment hot-melts the base cold-mix colored bitumen, and then disperses the slightly cold-mixed colored bitumen particles into the aqueous solution containing emulsifier through a machine to form liquid cold-mixed colored bitumen sheets.

Preventive pavement maintenance is a periodic mandatory maintenance measure, which is taken to restore the pavement surface service function when the pavement structure strength is sufficient and only the surface function is attenuated. New preventive maintenance technologies such as super-viscous fiber-added low-noise micro-surfacing and synchronous gravel seal have been widely used on the main lines of national highways, and the construction effect has been widely praised by customers.
Super-viscous fiber-added low-noise micro-surfacing starts with the gradation of micro-surfacing and the main material modified emulsified asphalt. By reducing the structural depth of the micro-surfacing and changing the distribution state of the coarse and fine materials on the surface of the micro-surfacing, the driving noise is reduced, while ensuring its anti-skid performance, effectively improving its adhesion, waterproofness, durability and crack resistance, and can solve the defects of easy detachment, excessive noise and reflective cracks of ordinary micro-surfacing.

When using asphalt melting equipment, you need to pay attention to the following points:
1. The power must be cut off during installation and operation to ensure safety.
2. Before starting operation, check whether all components are normal and have no fault prompts. In particular, the inspection of key parts such as the heater part and the conveyor belt device is particularly important.

What is an bitumen colloid mill used for? Everyone knows about colloid mill, but what about bitumen colloid mill?
Bitumen colloid mill is a high-tech multifunctional crushing and grinding equipment. The motor drives the rotating teeth and fixed teeth to rotate at high speed, generating a sharp speed gradient, which causes the boring to be strongly sheared, rubbed and turbulent, and finally achieves emulsification and dispersion. and homogenizing effect equipment.

In the cold winter, the following points should be noted when using bitumen melter equipment:

1. Keep warm: The bitumen melter equipment needs to be operated indoors or in a place with sunshade facilities, and ensure that the temperature of the bitumen melter and the surrounding environment is kept within an appropriate range.
2. Check the bitumen melting equipment: Before use, the bitumen melter should be checked, including whether the circuit, liquid circuit and other parts of the equipment are working properly, and whether the equipment has leakage, water leakage and other conditions.
3. Pay attention to safety: During operation, protective bitumen melter equipment should be worn to avoid direct contact with hot bitumen. At the same time, avoid overloading the bitumen melter to prevent equipment damage and safety accidents.
4. Control speed: Reasonably control the working speed of the bitumen melting equipment according to weather conditions and road conditions to avoid overheating of the equipment, which may cause the bitumen to flow too quickly or burn.
5. Storage conditions: When not in use, place the equipment in a dry, ventilated and moderately warm place, and ensure that the residue in the equipment is completely cleaned.

Bitumen emulsion equipment is widely used in new technologies and new processes for preventive maintenance. Bitumen emulsion plant is an emulsion at room temperature formed by dispersing bitumen into the water phase. It is a new material that is made of natural materials. It is different from traditional Compared with hot bitumen, it saves more than 50% of energy, saves 10%-20% of bitumen, and causes less pollution.

Improve the reliability of SBS bitumen emulsion plants: Once you have an established maintenance, it will help to identify problems. This will allow the maintenance plan and time to be carried out at your convenience. Regular maintenance will increase the normal operation time of SBS bitumen emulsification equipment, and it can be used when necessary. Low cost of operation: Imagine an SBS bitumen emulsification plant breaks down during a project. With a protective maintenance plan, such things happen less often because you have taken good care of the SBS bitumen emulsification plant.
If the SBS bitumen emulsification plant wants to maintain normal operation, then in the production process. All stages need to be maintained normal, among which the normality of the circuit system is an important aspect to ensure its smooth operation. Imagine that if there is a problem with the circuit during the on-site operation, it may affect the development of the entire project.
For users, of course, they don’t expect this to happen, so if the SBS bitumen emulsification plant is in the work of using the SBS bitumen emulsification equipment, if there is a circuit problem, it is necessary to take appropriate measures to solve it in time. The following article will give a detailed description of this problem, and the following SBS bitumen emulsification plant can be of benefit to everyone.

The Bitumen Emulsion Plant is mainly used for the production of sprayable emulsified bitumen applicated in pavement of prime coat, tack coat, and seal coat, etc. The essence of this plant is to melt bitumen and disperse bitumen in fine particles into water to be some kind of emulsion. It mainly consists of control system, core emulsifying machine components, measuring system, process pipelines, emulsifier dilution tank and pump, etc.

The bitumen decanter equipment is mainly composed of barrel removal shell (BOX), hoisting mechanism, hydraulic booster and electrical control system. The shell is divided into two chambers, the left and right chambers. The upper chamber is a chamber for melting a large barrel of bitumen (definition: the transformation process of a substance from solid to liquid). There are heating coils evenly distributed around it.

Precautions during the production of emulsified bitumen equipment. How much do you know about this information? Let’s learn more about it:
When the emulsified bitumen equipment is in production, the viscosity of the bitumen decreases with the increase of temperature. For every 12℃ increase, its dynamic viscosity decreases by about one time. During production, the base bitumen should be heated to liquid state before emulsification. In addition, in order to adapt to the emulsification capacity of the colloid mill, the base bitumen dynamic viscosity is generally controlled to be about 200cst. The lower the temperature, the higher the viscosity, which increases the burden on the bitumen pump and the colloid mill, making it difficult to emulsify; but on the other hand, in order to prevent the demulsification caused by excessive vaporization and evaporation of water in the finished product during the production of emulsified bitumen, it is impossible to heat the base bitumen temperature too high. Generally, the finished product temperature at the outlet of the colloid mill should be controlled to be less than 85℃.

Is the performance of Sinoroader’s fully automatic emulsified asphalt production equipment stable and unstable? To be honest, whether the performance of a product is stable or not can only be known through practice, right?
Chairman Mao, the great leader of China, once said, “Without practice, there is no right to speak.” Yes, people who have never used it naturally have no right to speak. Now the editor will talk about the fully automatic emulsified asphalt production equipment that I am using!

Asphalt melting equipment is one of the indispensable equipment in modern road construction. Its main function is to heat a large amount of cold hard asphalt to a suitable working temperature at the construction site. Advanced asphalt melting equipments can greatly improve construction efficiency, reduce human resources and time costs, and ensure pavement quality at the same time.
First of all, reliable asphalt melter equipment can shorten heating time and work efficiency and avoid wasting energy. Secondly, the equipment is easy to operate and can reduce the incidence of on-site safety accidents. In addition, this equipment has an automatic control and monitoring system that can adjust the working status and parameters at any time to meet different construction needs and environmental conditions.

In addition to being used according to regulations, modified bitumen equipment should also be maintained regularly in order to effectively extend the service life of modified bitumen equipment. The delivery pump of modified bitumen equipment, as well as its motor and reducer, need to be maintained in accordance with the specifications of the instructions. If the modified bitumen equipment is parked for a long time, the liquid in the tank and pipeline needs to be drained, and each moving component also needs to be filled with grease. The dust in the control box of the modified bitumen equipment needs to be cleaned once every six months. A dust blower can be used to remove dust to prevent dust from entering the machine and damaging parts. The micro powder machine needs to add unsalted butter once for every 100 tons of emulsified bitumen produced.

Modified material bitumen stripper, if the definition is simple, is an bitumen stripper. If described in detail, modified materials such as rubber powder or other fillers are added to the bitumen stripper, or an bitumen stripper is used to Block chemical substances such as photooxygen catalysis. The first is to change the chemical composition of the bitumen stripper, and the second is to use modified materials to equip the stripper with a certain spatial network structure, thereby improving its performance. Modified bitumen strippers mainly include vulcanized rubber and thermoplastic polyurethane elastomer modified bitumen strippers, plastic and anti-corrosion coating modified bitumen strippers and polymer modified bitumen strippers.

There are many ways to heat bitumen, including using fire source heating, electric heating, steam heating, hot water heating and indirect heating. Fire source heating generates heat by burning fuel to heat the bitumen to a molten state. Electric heating converts electrical energy into thermal energy through electric heating elements to heat the bitumen to a molten state. Steam heating transfers heat to bitumen through steam, heating the bitumen to a molten state. Hot water heating transfers heat to the bitumen through hot water, heating the bitumen to a molten state. Indirect heating transfers heat to the heating medium, which then transfers the heat to the bitumen to heat the bitumen to a molten state.

There are many types of emulsified bitumen, and PC-2 is one of them, which is a spray-type emulsified bitumen. It is used for spraying oil through the base layer of granular materials and health care spraying on semi-rigid base layers. There is also the PA-2 type, which has the same purpose as the PC-2 type. The difference is that the PC-2 type is a cation, while the PA-2 type is an anion.

Improve the understanding of the importance of preventive maintenance
We should further improve the understanding of the importance of preventive maintenance and raise preventive maintenance to the level of highway asset protection and road protection. At present, leaders at all levels and maintenance departments do not fully understand the significance of preventive maintenance of asphalt pavement. We should deepen our understanding of the important role of preventive maintenance and improve the strategic awareness, initiative and creativity of preventive maintenance. At the same time, the maintenance department should strengthen communication and exchanges with transportation authorities and financial management departments at all levels, so that departments at all levels understand the importance and necessity of preventive maintenance and create conditions for the implementation of preventive maintenance and funding sources. At the same time, it is very necessary to add preventive maintenance to the classification of maintenance projects, which will help the management of leaders at all levels and the implementation of preventive maintenance.
Improve the decision-making and planning of preventive maintenance
According to the decision-making and planning process, reasonably arrange the preventive maintenance of asphalt concrete pavement structure to ensure the safe and stable operation of highway projects throughout the life cycle, and reduce production costs while providing high-quality traffic services. Therefore, the key to preventive maintenance of asphalt concrete pavement structure lies in establishing a scientific decision-making and planning mechanism. The Ministry of Transport proposed in the “13th Five-Year Plan for Highway Maintenance Management Development” that the average annual mileage of preventive maintenance for expressways should not be less than 8%, and that for ordinary national and provincial roads should not be less than 5%. In the actual application process, local governments should also actively summarize experience and propose different preventive maintenance ratios based on the specific conditions of different regions.

Whether it is the application of modified asphalt equipment or the application of other equipment, if you want to extend its service life, you need to do daily maintenance work. In order to better help everyone, we have modified asphalt The maintenance methods that can be adopted when using the equipment are introduced as follows:

Emulsified asphalt (ingredients: asphaltene and resin) heating tank is a new type of equipment for heating emulsified asphalt. Its appearance replaces the traditional thermal oil heating equipment, which brings great convenience to our users and improves work efficiency. Then let’s take a detailed look at how it is better than the traditional thermal oil heating equipment.
Emulsified asphalt (ingredients: asphaltene and resin) heating tank is another new type of emulsified asphalt heating storage equipment developed by technically separating the characteristics of traditional thermal oil heating emulsified asphalt tanks and internal heat part (part) rapid emulsified asphalt heating tanks. The automatic circulation program of the asphalt heating equipment enables the asphalt to automatically enter the heater, dust collector, induced draft fan, asphalt pump, asphalt temperature display, water level display, and steam generator as required.
It consists of pipeline and asphalt pump preheating system, pressure relief system steam combustion system, tank cleaning system, oil unloading tank installation, etc. All are installed on the tank body (inside) to form a compact integrated structure. It fully compensates for the shortcomings of traditional thermal oil heating equipment, such as long heating time and high energy consumption.