Modified Bitumen Plant

In our daily life, we can often see emulsified asphalt equipment. Its appearance has brought us great convenience. So what is the difference between its modification process? Below, the editor will give you a brief introduction to the relevant knowledge points.
1. Emulsified asphalt equipment first emulsifies and then modifies: This is a relatively simple way to make modified emulsified asphalt. The production process is to grind hot asphalt and emulsifier soap together through a colloid mill to make ordinary emulsified asphalt, and then add latex-like modifiers to the emulsified asphalt through mechanical stirring to make modified emulsified asphalt. The characteristic of this method is that it does not require high equipment.

In the cold winter, you need to pay attention to the following points when using asphalt melting equipment:
1. Protection from cold and warmth: The equipment needs to be operated indoors or in a place with shading facilities, and ensure that the temperature of the equipment and the surrounding environment is maintained within an appropriate range.
2. Check the equipment: Before use, the equipment should be checked, including whether the circuits, fluid circuits and other parts of the equipment are working normally, and whether there are any leaks of electricity or water in the equipment.
3. Pay attention to safety: During operation, you should wear protective equipment and avoid direct contact with hot asphalt. At the same time, it is necessary to avoid equipment overload operation and prevent equipment damage and safety accidents.
4. Control speed: Reasonably control the working speed of the equipment according to weather conditions and road conditions to avoid overheating of the equipment, causing asphalt to flow too quickly or burn.
5. Storage conditions: When not in use, place the device in a dry, ventilated place with moderate temperature, and ensure that any residue in the device is completely removed.

Technical features of fiber sealing equipment:
1. Zero starting strong injection technology
With more than ten years of manufacturing history of asphalt spreading trucks and asphalt gravel synchronous sealing trucks, the zero-start strong spraying technology has been accumulated for many years. The combination of time-reliable hydraulic transmission components and Meitong’s control system can make the equipment instantly start from zero. Spraying starts in line, stable and reliable.
2. Duplex sealing structure
The sealing process of this equipment is a three-layer simultaneous and continuous construction process of one layer of asphalt + one layer of fiber + one layer of asphalt, forming a layer of interactive dense network winding structure, which fully meets the user’s construction requirements.

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.

Everyone has a side of themselves that they don’t want others to know. As a preventive road maintenance technology, slurry sealing has some shortcomings. do you think so?
Slurry seal is a kind of road protection that uses special equipment to mix emulsified asphalt, water, additives, aggregates, fillers and other ingredients in a certain proportion, and then mixes the slurry mixture onto the original road surface to form a thin layer. Maintenance technology. These are all well known. The editor will not go into details on this.

After the rubber bitumen storage tank is cleaned, the wood chips are sent to the rubber bitumen storage tank, and the wood chips and the bottom of the rubber bitumen storage tank are wiped with wood chips. The dirt and wood chips in the bitumen tank can be weathered naturally. The rubber bitumen storage tank is not allowed to be damaged. Check the technical specifications of the underwater concrete processing equipment and ventilation equipment.
The bottom of the rubber bitumen storage tank drain pipe is discharged from the drainage pipe, and the waste water is discharged into the empty tank or other containers through the inlet and outlet and the self-draining pipe. Open the Shenzhen manhole into the plastic suction pipe and pave the Shenzhen manhole with asbestos to reduce the discharge of oil and gas. When manually pumping the bottom oil, two people should be operated to improve the labor efficiency of the workers and send the fuel tank to supervision.

Regarding the basic knowledge of modified bitumen plant, I believe that many consumers have already had a basic understanding of it. Because of the continuous development of various fields today, various facilities including modified bitumen plants have been well developed and applied, and modified bitumen plant has gradually been recognized by customers.
The direct quick heating portable equipment in the modified bitumen equipment not only has a faster heating speed, saves fuel, and is pollution-free, but also convenient and easy to operate. The automatic heating system completely eliminates the trouble of baking or cleaning bitumen and pipelines.

Some of the equipment of emulsified modified bitumen equipment are as follows. The specially made bitumen filter can effectively filter the residues and dirt in the high-temperature culture medium bitumen to avoid damage to the subsequent equipment. The emulsified modified bitumen equipment adopts a spiral plate type or a shell and tube heat exchanger to quickly heat the culture medium bitumen through high-temperature heat transfer oil to meet the needs of the production process. The emulsified modified bitumen equipment is heated in the storage tank to prevent the bitumen from aging due to long-term high-temperature heating and exposure to the air. The sulfate generated during the production process of the emulsified modified bitumen equipment is very limited, reducing air pollution.
The emulsified modified bitumen equipment sends the modified material manually poured into the dumping bin to the bitumen batching tank by wind or spiral. It can be equipped with a metering and calibration system. The emulsified modified bitumen equipment thickener is automatically or manually added. The emulsified modified bitumen equipment can be equipped with a metering and calibration system. Emulsified modified bitumen equipment transportation and metering and calibration system, the emulsified modified bitumen equipment adds the set bitumen amount to the batching tank through the frequency converter and computer interlock. The emulsified modified bitumen equipment and bitumen steam flowmeter use big brand products to ensure the preparation.

Asphalt sealant is a material specially used for road crack repair. The following is a detailed introduction to asphalt sealant:
1. Definition and composition
Asphalt sealant is a road repair material made of asphalt or modified asphalt as the base material, with a certain amount of additives and fillers added, and processed by special technology. It usually has a black or dark brown appearance and is in a solid or semi-solid form.
2. Main characteristics
High adhesion: Asphalt sealant can firmly bond to the crack wall of the road surface to form a tight sealing layer to prevent moisture and other harmful substances from invading the road surface structure.
High elasticity: It has a certain elastic recovery ability and can adapt to the expansion and contraction changes of the road surface to prevent further expansion of cracks.
Weather resistance: After special process treatment, it has good weather resistance and can maintain its stable performance for a long time.
Convenient construction: The construction operation is simple and fast, without complex construction machinery, which reduces the construction cost.
3. Scope of application
Asphalt sealant is widely used in crack repair of various asphalt pavements, including highways, urban roads, airport runways, etc. At the same time, it can also be used for the maintenance and repair of asphalt surfaces such as bridges, tunnels, and parking lots.

No matter the application of emulsified asphalt equipment or other related equipment, in the application of appropriate maintenance work, today we introduce professional technicians to do the following 3 points to effectively improve the utilization rate of asphalt equipment:
1. When the emulsified asphalt plant is out of use for a long time, the liquid in the pipeline and storage tank should be discharged, the lid should be sealed, kept clean, and all moving parts are lubricated. When it is used for the first time and disabled for a long time, the rust of the oil tank should be removed, and the water filter should be cleaned regularly.
2. When the outdoor temperature is lower than -5℃, the emulsified asphalt production equipment shall not store the product without insulation device, and it should be discharged in time to avoid freezing and demulsification of emulsified asphalt.
3. The gap between the stator and the rotor of the emulsified asphalt equipment should be checked regularly. When the machine cannot meet the smaller gap requirements, the stator and rotor should be replaced.

The bitumen decanter equipment is mainly composed of barrel removal shell (BOX), hoisting mechanism, hydraulic booster and electrical control system. The shell is divided into two chambers, the left and right chambers. The upper chamber is a chamber for melting a large barrel of bitumen (definition: the transformation process of a substance from solid to liquid). There are heating coils evenly distributed around it.

The hydraulic bitumen decanter equipment produced by our company uses thermal oil as the heat carrier and has its own burner for heating. The thermal oil heats, melts, debarks and dehydrates the asphalt through the heating coil. This device can ensure that the asphalt does not age, and has the advantages of high thermal efficiency, fast barrel loading/unloading speed, improved labor intensity, and reduced environmental pollution.

Emulsified modified asphalt equipment is classified according to the production process and can be divided into three types: intermittent emulsified modified asphalt equipment, semi-continuous emulsified modified asphalt equipment, and continuous emulsified modified asphalt equipment. During the production of emulsified modified asphalt equipment, demulsifier, acid, water, and latex modified materials are blended in a soap mixing tank, and then pumped into the asphalt into the colloid mill. After a can of soap is used up, the soap is redispensed, and then the production of the next can is completed.
The emulsified modified asphalt equipment mentioned here includes hot water pumps and circulation pumps. This type of centrifugal water pump generally uses a pipeline centrifugal pump. There is a sewage outlet at the bottom of the pipeline centrifugal pump. Pay attention to the sewage outlet at the bottom of the emulsified modified asphalt equipment pump. The water in the water tank is released through the filter valve. Some emulsified modified asphalt equipment does not have a filter valve to save equipment costs, so it can only be emptied by loosening the flange bolts at the bottom. There are basically two methods of moisturizing emulsion pumps for emulsified modified asphalt equipment on the market, gear oil pumps or centrifugal water pumps. The gear oil pump can only drain the liquid in the pump through the connecting flange of the pipeline. The centrifugal water pump carries out sewage treatment through its own sewage outlet.
When used in the production of emulsified modified asphalt equipment, depending on the modified material technology, the latex pipeline can be connected in front of the colloid mill or behind the colloid mill, or there may be no latex pipeline and it must be made manually. Add the required amount of latex into the soap jar.

The selection of asphalt melting equipment should take into account factors such as the use environment, working conditions, and technical requirements. Common ones include hot oil heating equipment, electric heating equipment, and gas heating equipment.
Hot oil heating equipment is suitable for occasions that require long-term heating and high temperature control accuracy;
Electric heating equipment is suitable for small projects or occasions where temperature control accuracy is not required;
Gas heating equipment has the advantages of simple operation and low cost, but safety protection measures must be strictly followed.
When choosing, it is also necessary to comprehensively consider factors such as economy and environmental protection.

When using asphalt melting equipment, you need to pay attention to the following points:
1. The power must be cut off during installation and operation to ensure safety.
2. Before starting operation, check whether all components are normal and have no fault prompts. In particular, the inspection of key parts such as the heater part and the conveyor belt device is particularly important.

Modified material bitumen stripper, if the definition is simple, is an bitumen stripper. If described in detail, modified materials such as rubber powder or other fillers are added to the bitumen stripper, or an bitumen stripper is used to Block chemical substances such as photooxygen catalysis. The first is to change the chemical composition of the bitumen stripper, and the second is to use modified materials to equip the stripper with a certain spatial network structure, thereby improving its performance. Modified bitumen strippers mainly include vulcanized rubber and thermoplastic polyurethane elastomer modified bitumen strippers, plastic and anti-corrosion coating modified bitumen strippers and polymer modified bitumen strippers.

The viscosity of the bitimen melter equipment decreases as the temperature increases during the production process. Its output viscosity is about twice as high as every 12°C increase. During production, the base bitimen melter equipment must first be heated to a liquid state and then emulsified. In order to better integrate the emulsification ability of colloid milling, the viscosity of base bitimen melter is generally controlled to be about 200 cst. The lower the temperature, the higher the viscosity, which increases the pressure on the bitimen melter pump and colloid milling, making emulsification impossible: However, on the other hand, in order to prevent the asphalt debarrel equipment from weaning when the moisture of th

Contemporary roads and pavements have undergone many changes: traffic volume and driving frequency have increased significantly, the axle load of logistics trucks has continued to increase, one-way driving in separate lanes has been widely implemented, and regulations have further improved the anti-flow resistance of the ground, that is, the work of modified asphalt equipment under high temperatures ability;

Improve the reliability of SBS bitumen emulsion plants: Once you have an established maintenance, it will help to identify problems. This will allow the maintenance plan and time to be carried out at your convenience. Regular maintenance will increase the normal operation time of SBS bitumen emulsification equipment, and it can be used when necessary. Low cost of operation: Imagine an SBS bitumen emulsification plant breaks down during a project. With a protective maintenance plan, such things happen less often because you have taken good care of the SBS bitumen emulsification plant.
If the SBS bitumen emulsification plant wants to maintain normal operation, then in the production process. All stages need to be maintained normal, among which the normality of the circuit system is an important aspect to ensure its smooth operation. Imagine that if there is a problem with the circuit during the on-site operation, it may affect the development of the entire project.
For users, of course, they don’t expect this to happen, so if the SBS bitumen emulsification plant is in the work of using the SBS bitumen emulsification equipment, if there is a circuit problem, it is necessary to take appropriate measures to solve it in time. The following article will give a detailed description of this problem, and the following SBS bitumen emulsification plant can be of benefit to everyone.

Bitumen emulsifier is a surfactant. A surfactant is a compound that reduces the surface tension between two liquids, a gas and a liquid, or a solid and a liquid. Surfactants are mainly used in: detergents, detergents, fabric softeners, wetting agents, emulsifiers, foaming agents, dispersants, adhesives, etc.

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

Asphalt spreader is used to spread the penetration oil, waterproof layer and bonding layer of the bottom layer of asphalt pavement of high-grade highway. It can also be used for the construction of county and township highway oil roads with layered paving technology. It consists of a car chassis, an asphalt tank, an asphalt pumping and spraying system, a thermal oil heating system, a hydraulic system, a combustion system, a control system, a pneumatic system, and an operating platform.
Knowing how to properly operate and maintain the asphalt spreader can not only extend the service life of the equipment, but also enable the construction project to proceed smoothly. So what problems should the asphalt spreader pay attention to when working? The technicians of Gaoyuan Road Construction Machinery Equipment Co., Ltd. give you tips:
1). Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreader, check the four thermal oil valves and the pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Test the asphalt pump and circulate for 5 minutes. If the pump head shell is hot, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not turn or make noise. In this case, the valve needs to be opened to continue heating the asphalt pump until it can operate normally. During the working process, the asphalt liquid must be kept at a working temperature of 160~180℃, and it cannot be filled too full (pay attention to the liquid level pointer during the injection of asphalt liquid, and check the tank mouth at any time). After the asphalt liquid is injected, the filling port must be closed tightly to prevent the asphalt liquid from overflowing during transportation.
2). During use, asphalt may not be pumped in. At this time, it is necessary to check whether the interface of the asphalt suction pipe is leaking. When the asphalt pump and pipeline are blocked by solidified asphalt, a blowtorch can be used for baking, and the pump must not be forced to turn. When baking, care should be taken to avoid directly baking the ball valve and rubber parts.
3). When spraying asphalt, the car should be driven at a low speed. Do not step on the accelerator hard, otherwise it may cause damage to the clutch, asphalt pump and other components. If 6m wide asphalt is spread, pay attention to obstacles on both sides at any time to prevent collision with the spreading pipe. At the same time, the asphalt should be kept in a large circulation state until the spreading work is completed. After the work is completed every day, if there is any remaining asphalt, it must be returned to the asphalt pool, otherwise it will solidify in the tank and cannot work next time.
4). In addition, the emulsifier must also pay attention to daily maintenance:
1. The emulsifier and delivery pump and other motors, agitators, and valves should be maintained daily.
2. The emulsifier should be cleaned after work every day.
3. The speed regulating pump used to control the flow should be regularly tested for accuracy, and adjusted and maintained in time. The asphalt emulsifier should regularly check the matching clearance between its stator and rotor. When the minimum clearance specified by the machine cannot be reached, the stator and rotor should be replaced.
4. If the equipment is out of use for a long time, the liquid in the tank and pipeline should be emptied (the emulsifier aqueous solution should not be stored for a long time), the hole covers should be tightly closed, kept clean, and the running parts should be filled with lubricating oil. When it is used for the first time or when it is used again after a long period of inactivity, the rust in the tank should be removed, and the water filter should be cleaned regularly.
5. Regularly check whether the terminal in the electric control cabinet is loose, whether the wires are worn during shipment, and remove dust to avoid damage to the machine parts. The frequency converter is a precision instrument. Please refer to the instruction manual for specific use and maintenance.
6. There is a heat transfer oil coil in the emulsifier water solution heating stirring tank. When injecting cold water into the water tank, the heat transfer oil switch should be turned off first, and then the switch should be turned on to heat after adding the required amount of water. Pouring cold water directly into the high-temperature heat transfer oil pipeline can easily cause the weld to crack.

The modified asphalt equipment estimates the quality and uniformity of various raw materials from the material pile and conveyor at any time. The modified asphalt equipment checks the soil and oversized gravel, and checks whether there is any leakage in the cold hopper. Estimate whether the mixed material is mixed evenly, whether there is white material, whether the oil-stone ratio is reasonable, and check the concrete segregation of the asphalt mixture and the mixed material.
The modified asphalt equipment checks the control parameters of various basic parameters of the mixing device in the control room, the display values ??of the control screen, and the modified asphalt equipment checks whether the data statistics and display values ??of the computer and printout are consistent. Test the raw material heating temperature and the mixed material entry temperature of the modified asphalt equipment.

There are many types of emulsified bitumen, and PC-2 is one of them, which is a spray-type emulsified bitumen. It is used for spraying oil through the base layer of granular materials and health care spraying on semi-rigid base layers. There is also the PA-2 type, which has the same purpose as the PC-2 type. The difference is that the PC-2 type is a cation, while the PA-2 type is an anion.

1 Common diseases of asphalt pavement
There are nine phenomena of early damage to asphalt pavement: rutting, cracks, and potholes. These diseases are the most common and serious, and are one of the common quality problems of highway projects.
1.1 Rutting
Rutting refers to the longitudinal strip grooves on the road surface along the wheel tracks, with a depth of more than 1.5cm. Rutting is a strip groove formed by the accumulation of permanent deformation of the road surface under the repeated action of vehicle load. Rutting reduces the smoothness of the road surface. When the rutting reaches a certain depth, due to the accumulation of water in the rutting, it is easy for cars to slide and cause traffic accidents. The main reasons for rutting are unreasonable design and serious overloading of vehicles.
1.2 Cracks
There are three main forms of cracks: longitudinal cracks, transverse cracks and mesh cracks. When cracks occur in asphalt pavement, water seepage occurs, which harms the surface layer and base layer.
1.3 Potholes
Potholes are common early diseases of asphalt pavement, which refer to the road surface being damaged into potholes with a depth of more than 2cm and an area of ??more than 0.04㎡. The main reason for the formation of potholes is that the oil used in vehicle repair or motor vehicles seeps into the road surface, polluting the asphalt mixture and causing it to loosen. The pits are gradually formed by driving and rolling.

The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) Open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.