Operation process of emulsified asphalt equipment

We need to prepare a lot of work when using modified asphalt equipment. What kind of work do we need to prepare? Next, let me briefly introduce the relevant knowledge points.
1. Heat transfer oil heats and insulates the modified asphalt equipment and nozzle. After spraying, the asphalt pump and nozzle do not need to be cleaned with diesel. Use high-pressure air to press the asphalt in the pipeline and spray pipe back to the tank, and then blow the nozzle; use heat transfer oil to keep warm, so that the pipeline and nozzle are smooth and unobstructed. 2. Various asphalts can be spread: high-viscosity asphalt, hot asphalt, emulsified asphalt, etc.; the spreading width can be freely adjusted, each nozzle can be controlled separately, and the maximum spraying width is up to 6m. Flexible handheld spray guns can be used to spray asphalt on corners. 3. Excellent thermal insulation performance, average cooling ≤1-2℃/h. 4. Convenient loading and unloading function. In addition to filling asphalt from the asphalt tank port, hot asphalt can be sucked out by itself, and external asphalt can also be pumped and transferred. 5. The modified asphalt equipment is evenly spread, and the nozzle design can be used for triple overlapping spraying.
The above are the relevant knowledge points of modified asphalt equipment. I hope the above content can be helpful to everyone. Thank you for your viewing and support. More information will be sorted out for you later. Please pay attention to our website updates.

Some of the equipment of emulsified modified bitumen equipment are as follows. The specially made bitumen filter can effectively filter the residues and dirt in the high-temperature culture medium bitumen to avoid damage to the subsequent equipment. The emulsified modified bitumen equipment adopts a spiral plate type or a shell and tube heat exchanger to quickly heat the culture medium bitumen through high-temperature heat transfer oil to meet the needs of the production process. The emulsified modified bitumen equipment is heated in the storage tank to prevent the bitumen from aging due to long-term high-temperature heating and exposure to the air. The sulfate generated during the production process of the emulsified modified bitumen equipment is very limited, reducing air pollution.
The emulsified modified bitumen equipment sends the modified material manually poured into the dumping bin to the bitumen batching tank by wind or spiral. It can be equipped with a metering and calibration system. The emulsified modified bitumen equipment thickener is automatically or manually added. The emulsified modified bitumen equipment can be equipped with a metering and calibration system. Emulsified modified bitumen equipment transportation and metering and calibration system, the emulsified modified bitumen equipment adds the set bitumen amount to the batching tank through the frequency converter and computer interlock. The emulsified modified bitumen equipment and bitumen steam flowmeter use big brand products to ensure the preparation.

Based on the characteristics of the high-speed hot mixed bitumen melting equipment, the direct heating bitumen melter equipment tank is a researched, environmentally friendly and energy-saving thermal mixed bitumen melting equipment, which can directly coordinate the temperature of the direct heating bitumen melter heating tank and protect the direct heating asphalt melter equipment. Barrel heating tank. The temperature of hot mixed asphalt barrels achieves the appropriate storage temperature.
When the water level in the drum is lower than the temperature of the thermometer, please close the suction valve before the drum pump is shut down to prevent the drum from flowing back in the heater. After the motor has been running for 2 days, the three-way valve opens quickly.

How to reduce the energy consumption of emulsified asphalt production equipment is a concern of many users, and is also an issue that many manufacturers attach great importance to. Therefore, today Sinoroader, as a manufacturer of emulsified asphalt production equipment, would like to take this opportunity to share with you how to reduce the production of emulsified asphalt. Equipment energy consumption method.
Since emulsified asphalt appears as a finished product in emulsified asphalt production equipment, and the outlet temperature of ordinary emulsified asphalt is about 85°C, the outlet temperature of emulsified modified asphalt is above 95°C, so there is a lot of latent heat in emulsified asphalt, but emulsified asphalt The production equipment does not make good use of them, but directly enters the finished product tank, allowing the heat to be lost at will, resulting in a waste of energy.

Maintenance points of asphalt spreading trucks in different working hours
per month (or every 200 hours worked)；
​Per year (or every 500 hours worked)；
Every two years (or every 1,000 hours worked)；

The modified asphalt equipment estimates the quality and uniformity of various raw materials from the material pile and conveyor at any time. The modified asphalt equipment checks the soil and oversized gravel, and checks whether there is any leakage in the cold hopper. Estimate whether the mixed material is mixed evenly, whether there is white material, whether the oil-stone ratio is reasonable, and check the concrete segregation of the asphalt mixture and the mixed material.
The modified asphalt equipment checks the control parameters of various basic parameters of the mixing device in the control room, the display values ??of the control screen, and the modified asphalt equipment checks whether the data statistics and display values ??of the computer and printout are consistent. Test the raw material heating temperature and the mixed material entry temperature of the modified asphalt equipment.

As we all know, emulsified bitumen is a single-component black viscous liquid that can combine the roadbed and the pavement to improve the performance and service life of the road. So what problems should be paid attention to when using emulsified bitumen? Let’s follow the editor of Sinoroader Group, an emulsified bitumen manufacturer, to learn about it.

As a manufacturer with many years of experience in emulsified bitumen construction, Sinoroader Group believes that everyone needs to pay attention to the following 2 points when using it:

Whether it is the application of modified asphalt equipment or the application of other equipment, if you want to extend its service life, you need to do daily maintenance work. In order to better help everyone, we have modified asphalt The maintenance methods that can be adopted when using the equipment are introduced as follows:

For each equipment used, certain safety knowledge must be followed. For the use of emulsified asphalt equipment, detailed instructions are given:
1. Placement: The emulsified asphalt equipment should be placed on a flat place, the front axle should be fixed to the sleepers, and the tires should be dangling. The machine should not be fiddled with at will to affect normal operation.
2. Regularly check whether the mixer blades are deformed and the screws are loose.
3. Check whether the running direction of the mixing drum is consistent with the direction of the arrow. Please replace the positive and negative poles of the terminal.
4. Before turning on the power, check the no-load test run, check for air leakage, and check the idling speed of the mixing barrel. The normal speed is about 3 times faster than the empty car. If not, stop the inspection.
5. If the asphalt material is stopped for one hour after mixing, clean the mixing barrel, pour in clean water, and clean the mortar. Then drain the water. Remember that there should be no water in the barrel to prevent the formula from changing, so that the page and other links will rust. Sinoroader will provide you with more safe emulsified asphalt knowledge, please continue to browse.

Asphalt mixture is a kind of composite material, mainly composed of asphalt, coarse aggregate, fine aggregate, mineral powder, some also added polymer and wood cellulose; By these different quality and quantity of materials mixed to form different structures, and have different mechanical properties

Emulsion bitumen manchine is widely used in new technologies and new processes for preventive maintenance. Emulsion bitumen manchine is an emulsion at room temperature formed by dispersing asphalt into the water phase. It is a new material that is made of natural materials. It is different from traditional Compared with hot asphalt, it saves more than 50% of energy, saves 10%-20% of asphalt, and causes less pollution.

The emulsified bitumen equipment hot-melts the base cold-mix colored bitumen, and then disperses the slightly cold-mixed colored bitumen particles into the aqueous solution containing emulsifier through a machine to form liquid cold-mixed colored bitumen sheets.

The selection of asphalt melting equipment should take into account factors such as the use environment, working conditions, and technical requirements. Common ones include hot oil heating equipment, electric heating equipment, and gas heating equipment.
Hot oil heating equipment is suitable for occasions that require long-term heating and high temperature control accuracy;
Electric heating equipment is suitable for small projects or occasions where temperature control accuracy is not required;
Gas heating equipment has the advantages of simple operation and low cost, but safety protection measures must be strictly followed.
When choosing, it is also necessary to comprehensively consider factors such as economy and environmental protection.

Synchronous chip seal is a process technology for treating cracks in asphalt pavement, and it is currently a highway construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical characteristics are? If you don’t know, follow the editor of Sinoroader company to have a look.

Changing the color of asphalt pavement is an important project aimed at improving the beauty of roads, optimizing traffic signs and enhancing urban landscape effects. The following is a detailed introduction to the color change of asphalt pavement:
1. Color change method
Using pavement color change spray:
Spray directly on the original asphalt pavement surface to make the road surface look brand new.
This method is simple and fast to construct, with bright and lasting colors, and will not change the structure of the pavement.

Bitumen emulsifier is a surfactant. A surfactant is a compound that reduces the surface tension between two liquids, a gas and a liquid, or a solid and a liquid. Surfactants are mainly used in: detergents, detergents, fabric softeners, wetting agents, emulsifiers, foaming agents, dispersants, adhesives, etc.

Analysis of the necessity of emulsified bitumen equipment in modern road construction projects With the acceleration of the construction speed of transportation infrastructure, the construction standards are getting higher and higher, and higher requirements are also put forward for the use of emulsified bitumen in the closed layer of fly ash and the adhesive layer between the new and old ground.

From three aspects, emulsion bitumen equipment has good economic performance:
First, energy saving. The kerosene or gasoline content in diluted asphalt can reach 50%, while the emulsion bitumen plant only contains 0-2%. This is a valuable saving behavior in the production and utilization of white fuel. By simply increasing the viscosity standard of asphalt by adding light oil solvent, asphalt can be poured and spread, and it is hoped that the light oil after use can evaporate into the atmosphere.
Second, versatility. There are many application methods for emulsion bitumen plants, and the appropriate method needs to be selected when applying it. The same emulsion can be used for large-scale sealing and can be used for small-scale pit repair work. Because they can be stored in tanks for a long time, they are very easy to use when applied in remote areas.
Third, it is easy to use. The professional spreading of emulsions requires professional equipment, such as spreaders. Small-area emulsion applications can be directly poured and spread by hand, such as small-area pit repair work, crack fillers, etc. Small quantities of cold mixes only require basic equipment.

Synchronous gravel sealing technology refers to the use of special synchronous gravel sealing truck equipment to lay and roll prepared gravel, asphalt and other materials to build a single layer of asphalt gravel wearing layer, which is important for highway pavement. protection of. From the perspective of characteristics, it is simple and easy to implement. It has obvious effects on the prevention of highway diseases, problem solving, later maintenance, and improvement of grade protection. It can also well extend the service life of highways.

Recently, I found that many people don’t know much about the operation skills of asphalt pavement spreaders. If you also want to know what’s going on, you can read this introduction below.
Asphalt pavement spreaders are an indispensable and important equipment in road maintenance and construction. Their operation skills directly affect construction efficiency and project quality. The following introduces the operation skills of asphalt pavement spreaders from four aspects: pre-operation preparation, precautions during construction, spreading skills, and post-operation cleaning and maintenance:

Emulsified asphalt equipment is a special equipment for producing emulsified asphalt. The emulsified asphalt produced by emulsified asphalt equipment is used in many industries. I wonder how much you know about the emulsified asphalt produced by emulsified asphalt equipment. Let’s take a look at them one by one:
Slurry seal is a cold mix asphalt mixture with the advantages of aggregate and asphalt mixing. Under normal circumstances, similar graded slurry seal has a higher modulus than hot mix asphalt mixture, so it is often used to fill road rutting. The higher stability has a higher resistance to deformation. The mixture is usually composed of harder fine aggregate grading and wear-resistant aggregate with high sand equivalent, especially micro-seal and polymer-modified seal. This greatly increases the strength and integrity of the road surface. This makes the road surface have high wear resistance and excellent deformation resistance. Emulsified asphalt emulsion is also easy to use on a mobile slurry seal paver, where mixing and admixtures are used for chemical control to meet maintenance needs.

Stainless steel bitumen melters use bitumen concrete micro-powder machines. Its blade strength is high, the angular velocity of the moving disc is high, and the gap can be adjusted to 0.15mm. Stainless steel bitumen melters are suitable for the production and processing of various polymer bitumen concrete, such as SBS, PE, EVA, etc.
Stainless steel bitumen melters use independently developed special batching tanks, stainless steel bitumen melter force stirring devices, liquid level meter overflow prevention equipment, granular material dosage and equipment, liquid additive automatic addition equipment and other production key points. It ensures the full-position process guarantee for the stainless steel bitumen melter of the bitumen concrete production line. The stainless steel bitumen melter processing stainless steel bitumen melter rate is significantly increased, and the quality of stainless steel bitumen melters is greatly improved.

With the rapid development of highway construction and the increase in demand for asphalt, barreled bitumen has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported bitumen used in high-grade highways is in barrel form, which requires an bitumen melter equipment with fast melting speed, clean debarreling, and prevention of asphalt aging.
The upper part of the debarreler of the bitumen melter equipment is hotter, and each barrel is directly heated by the heat transfer oil coil. The barrel wall directly bears the heat radiation of the heating coil. The asphalt is cleanly and sensitively debarreled, and there will be no waste of asphalt hanging barrels. According to the principle of layered heating, four-layer heating technology is adopted, with single inlet and single outlet of heat transfer oil, and high thermal efficiency of heating; at the same time, the waste heat of combustion exhaust gas is used for secondary heating, and power is effectively used; the debarreler body is insulated with high-quality rock wool material. It is suitable for various types of imported and domestic barrels, and the deformation of asphalt barrels will not affect production.

Precautions for checking emulsified asphalt equipment
Sinoroader emulsified asphalt pavement engineering common equipment, now has gradually been widely used.
We all know that before any equipment is used, the equipment should be preliminarily inspected to check whether the installation is normal, and then put into use. The use of modified asphalt modified asphalt production equipment can also extend the peak season. The modified asphalt and stone water machine can be mixed with wet stone to form a continuous film under the surface conditions of low-temperature asphalt and stone. The viscosity of the asphalt is low and the viscosity of the emulsified asphalt is low. Wet film below 10 degrees.

Abstract: Asphalt melting equipment is one of the indispensable equipment in modern road construction. Its main function is to heat a large amount of cold hard asphalt to a suitable working temperature at the construction site. Advanced asphalt melting equipment can greatly improve construction efficiency, reduce human resources and time costs, and ensure pavement quality at the same time.

How to reduce energy consumption of emulsified asphalt machinery is a concern of many users and many manufacturers. Therefore, today, Sinosun Company, as a manufacturer of emulsified asphalt equipment, would like to take this opportunity to share with you the method of reducing energy consumption of emulsified asphalt machinery.
Since emulsified asphalt appears as a finished product in emulsified asphalt machinery, and the outlet temperature of ordinary emulsified asphalt is about 85℃, and the outlet temperature of emulsified modified asphalt is above 95℃, there is a lot of latent heat in emulsified asphalt, but the emulsified asphalt equipment does not make good use of them, but directly enters the finished product tank, allowing heat to be lost at will, resulting in energy waste.

Bitumen decanter equipment can be placed in a complex system as an independent unit, replacing the existing heat source de-barreling method, or in parallel as a core component of a large set of equipment, or it can work independently to meet the requirements of small-scale construction operations.
The Sinoroader bitumen decanter device is mainly composed of a de-barreling box, a lifting mechanism, a hydraulic thruster and an electrical control system. The box is divided into two chambers, the upper chamber is a barreled bitumen melting chamber, and heating coils are evenly distributed around it. The heating pipe and the bitumen barrel mainly exchange heat in a radiation manner to achieve the purpose of bitumen de-barreling. Several guide rails are the tracks for the bitumen barrel to enter. The lower chamber is mainly to continue heating the bitumen removed from the barrel to make the temperature reach the suction pump temperature (100℃), and then the asphalt pump is pumped into the upper chamber. At the same time, an empty barrel is pushed out at the rear end outlet. There is also an oil tank on the platform at the entrance of the asphalt barrel to prevent the dripping bitumen from flowing out.
The inlet and outlet doors of the device adopt a spring automatic closing mechanism. The door can be automatically closed after the asphalt barrel is pushed in or out to reduce heat loss. A temperature gauge is installed at the asphalt outlet to observe the asphalt outlet temperature. The electrical control system can control the opening and closing of the hydraulic pump and the reversing of the electromagnetic reversing valve to realize the advance and retreat of the hydraulic cylinder. If the heating time is extended, a higher temperature can be obtained. The lifting mechanism adopts a cantilever structure. The bitumen barrel is lifted by an electric hoist, and then moved horizontally to place the bitumen barrel on the guide rail. A temperature gauge is installed at the outlet of the asphalt meltering equipment to observe its outlet temperature.

Asphalt spreader is an irreplaceable tool for highway maintenance. Asphalt spreader is an irreplaceable tool for highway maintenance. Highway maintenance is divided into four categories according to the nature of the project, scale, and technical complexity: minor repair, medium repair, major repair, and improvement. Specific classification:
(1) Minor repair and maintenance project: preventive maintenance and repair of slightly damaged parts of the highway and all its engineering facilities to keep them in good condition. It is usually planned and carried out daily by the maintenance team within the annual minor repair and maintenance quota funds on a monthly (ten-day) basis.
(2) Medium repair project: regular repair and reinforcement of general wear and tear and local damage of highway engineering facilities to restore them to their original state. It is usually planned and implemented by grassroots road maintenance agencies on an annual (seasonal) basis.
(3) Major repair project: periodic comprehensive repair of major damage to highway facilities to fully restore them to the original design standards, or local improvements and individual additions within the original technical level to gradually improve the highway’s traffic capacity. It is usually organized and implemented by grassroots road maintenance agencies or with the help of their superior agencies according to the approved annual project budget.
(4) Improvement projects are large projects that improve the technical level of roads and their engineering facilities in stages and sections due to their inability to meet traffic volume and load requirements, or significantly improve traffic capacity through improvements. It is usually organized and implemented or completed through bidding by regional road maintenance agencies or provincial road maintenance agencies according to the approved plan and design budget. As a manufacturer of asphalt spreaders, we welcome you to visit us.

Microsurfacing is a thin layer of overlay placed on old asphalt pavement and is a type of preventive maintenance process. The purpose of microsurfacing is road maintenance. After micro-surface paving, it can repair cracks in the original road surface, waterproof and beautify the road surface.
The construction method of micro surfacing is: using a micro surfacing paver to evenly spread modified emulsified asphalt, a certain grade of mineral materials, water and other additives on the road surface in a certain proportion.

Modified (rubber powder) bitumen equipment, one of the road maintenance equipment. It is a kind of equipment that measures, mixes and develops SBS, rubber powder and asphalt.
Modified (rubber powder) bitumen equipment is a set of wet modification processing technology, which mainly consists of modified material metering and promotion, bitumen rapid heating, asphalt metering, high-intensity mixing tank, mixed material transfer pump, development tank, colloid mill, Control system and other components.