Requirements for asphalt mixing plants when in use

After use, asphalt mixing equipment needs to be disassembled, cleaned, and maintained before it can be saved for next use. Not only is the disassembly process of the equipment important, but the previous preparation work also has a greater impact, so it cannot be neglected. Please pay attention to the detailed introduction below for specific content.

Natural gas is a colorless, odorless, flammable and explosive gas, the main component of which is methane, which accounts for about 98% of natural gas. The density of natural gas is lower than that of air and it is difficult to liquefy. Natural gas is not only a clean green energy for civil, commercial and industrial use, but also a raw gas for chemical industry. The theoretical ignition value of natural gas is 540 degrees, the combustion temperature is 1970 degrees, the calorific value is 40MJ/m3, and the explosion limit is 5%-15%. CNG refers to natural gas that has been compressed to 20-25MP and stored in high-pressure gas tank trucks, and then transported to various gas transmission points to supply gas to residential users, commercial users and industrial users. In order to ensure the normal operation and safety of the asphalt mixing station and our pressure regulating station, our company has specially formulated the following safety protection measures.

Asphalt mixing plant is a relatively important complete set of equipment in people’s lives. There are many components of this equipment, such as grading machine, vibrating screen, belt feeder, powder conveyor, elevator and other parts. Plug valve is one of them, so what is the specific role of plug valve in asphalt mixing plant? This article will give a brief introduction.
The plug valve is first of all a closure or plunger-shaped rotary valve. Generally, it is necessary to rotate 90 degrees to make the channel opening on the valve plug the same as that on the valve body, or to split it to play the role of opening or closing. The shape of the plug valve in the asphalt mixing plant is generally cylindrical or conical.

During the operation of the asphalt mixing plant, the quality of the mixture is often related to its construction quality. Therefore, we need to improve the quality level of the mixture as much as possible, and the temperature of the mixture is one of the standards for the qualification assessment of the mixture. In other words, if the temperature is too high or too low, the mixture may become waste and cannot meet the needs of use.
Therefore, reasonable control of the temperature of the mixture is one of the basic conditions that must be met for the normal production of the asphalt mixing plant. Among them, the quality of the fuel will affect the temperature of the mixture. For example, if the quality of the fuel is poor, the calorific value is low, and the combustion is incomplete, it will lead to unstable heating, low temperature, and a large amount of residue will be produced after combustion, affecting the quality of the mixture. If the viscosity is large, it will also cause ignition difficulties and the temperature is not easy to control.

Asphalt mixing plant equipment is mainly composed of batching system, drying system, ignition system, hot material lifting, vibrating screen, hot material storage bin, weighing mixing system, asphalt supply system, granular material supply system, dust removal system, finished product hopper and automatic control system.
Components:
⑴ Grading machine
⑵ Vibrating screen
⑶ Belt vibrating feeder
⑷ Granular material belt conveyor
⑸ Drying mixing drum;
⑹ Coal powder burner
⑺ Dust removal equipment
⑻ Bucket elevator
⑼ Finished product hopper
⑽ Asphalt supply system;
⑾ Distribution station
⑿ Automatic control system.

Due to its complexity and importance, asphalt mixing plants are more critical in road construction. Modern asphalt mixing stations have five key systems. Do you know what they are?
1. Mixing system of asphalt mixing plant
Mixing equipment is one of the key systems, why? Usually, the productivity of the mixing equipment has a great impact on the next step of construction efficiency. Most asphalt mixing plants use twin-shaft forced mixing. Since the drying drum and burner of the mixing equipment have strong overload capabilities, and in most cases, the moisture content of the mineral materials is less than 5%, this improves the productivity of the mixing equipment. provide conditions. The mixing blades of the mixer have an adjustable assembly angle and are driven by dual mixing shafts and dual motors.

The quality of asphalt mixture directly determines the quality of asphalt pavement engineering. This article discusses the key points of supervision of ordinary highway asphalt plants in order to better monitor the quality of asphalt mixture.

The plug valve is a rotary valve in the shape of a closure or plunger. After rotating 90 degrees, the channel opening on the valve plug is the same as or separated from the channel opening on the valve body to complete opening or closing. It is widely used in oilfield excavation, transportation and refining equipment, and such valves are also needed in asphalt mixing plants.
The valve plug of the plug valve in the asphalt mixing plant can be cylindrical or conical. In the cylindrical valve plug, the channel is generally rectangular; in the conical valve plug, the channel is trapezoidal. These shapes make the structure of the plug valve light and very suitable for blocking and connecting media and diversion.

When an ordinary asphalt mixing station completes the mixing operation, it will cause great pollution to the surrounding environment. In order to solve this problem, environmentally friendly asphalt mixing equipment came into being. What are the characteristics of this type of equipment?

There is also a reversing valve in the asphalt mixer, which generally does not cause problems, so I have not understood its solution in detail before. But in actual use, we encountered this kind of failure. How should we deal with it?

Asphalt mixing stations have always been criticized for pollution due to the emission of harmful smoke and dust and high energy consumption. Asphalt mixing stations with high pollution, high energy consumption and unqualified environmental protection are obviously incompatible with modern urban development. Under the high pressure of environmental protection supervision, how can asphalt mixing stations pass environmental protection inspections smoothly? Can asphalt mixing stations be low-carbon, energy-saving, and environmentally friendly, and achieve environmental protection upgrades?
As a professional asphalt mixing equipment R&D and manufacturer, how to make asphalt mixing stations more environmentally friendly and energy-saving has always been the direction of Nanfang Road Machinery’s efforts. In response to the pollution problems faced by asphalt mixing stations, Nanfang Road Machinery has launched environmentally friendly asphalt mixing equipment with strict environmental protection standards.

1.During the operation of asphalt mixing station equipment, in addition to ensuring that the asphalt mixing station equipment is in good condition, it should also be equipped with a mineral moisture content detector and a finished material tester, and the relevant data should be frequently tested for the operator to adjust the operation in time, so as to keep the equipment in good condition.
2. In addition to affecting production capacity, the moisture content of mineral materials is also the main factor that determines fuel consumption. Additional material sheds should be added.
3. Before operation, all working parts and devices of the asphalt mixing station equipment should be fully checked to see if they are intact and normal. If there is a problem, it must be properly handled before operation, and it is forbidden to operate with illness.

Asphalt mixing plant is a complete set of equipment composed of many systems. It is widely used in the current society. Its components include batching system, drying system, combustion system, hot material lifting, weighing and mixing system and control system.
In the process of asphalt mixing, heating is an indispensable link, because there must be a system for heating in the asphalt mixing station, but the system generally fails for various reasons. So how should the heating system of the asphalt mixing station be improved? This article will briefly explain this issue.
Generally speaking, when the asphalt mixing station is running under low temperature conditions, the asphalt circulation pump and spray pump cannot operate normally, which will cause the asphalt in the asphalt scale to solidify, and then the asphalt mixing station cannot be produced. Therefore, the asphalt mixing station needs a heating system during operation.

If you look at an asphalt mixing plant from a professional perspective, do you know how to judge its work and significance? In fact, the so-called asphalt mixing station is the one that produces asphalt. We can usually see it in road construction projects. Specifically, it mixes some materials that need to be used during the construction process according to certain proportion requirements. Then complete the corresponding construction work.
Then, we can analyze it from a market perspective. Since it was used in the market, it has been widely praised by users. Today’s asphalt mixing plant technology has been greatly improved, and the entire set of equipment used has a variety of advantages. , such as meeting the requirements of stable control, screening, efficient dust removal, excellent mixing, and green environmental protection during the work process. It is even more obvious when used in large-scale projects such as high-grade highways and airports.

Asphalt mixing plant refers to a complete set of equipment used for batch production of asphalt concrete. Its main function is to produce asphalt mixture, colored asphalt mixture, etc., and has been widely used in road construction. However, during the production process of asphalt mixture, pollutants such as noise, dust, and asphalt smoke will be produced, seriously polluting the environment and threatening the health of workers. Therefore, under the current background of building a resource-saving and environment-friendly society in our country, it is very important to save energy and reduce consumption during the use of asphalt mixing plants. The following article mainly starts from the three factors that affect the asphalt mixing plant, and explores the energy saving and consumption reduction measures of the asphalt mixing plant, aiming to reduce the cost of asphalt production and improve the efficiency of the asphalt plant.

Asphalt mixing plant is a very practical engineering machinery. Especially in the road construction process, it plays an irreplaceable role. Due to its importance, in addition to ensuring its own quality, the use and maintenance of the equipment must be carried out normally. Let’s learn about the daily maintenance requirements of asphalt mixing plants.

Many people think that since both asphalt mixing plants and asphalt mixing plants are equipment for producing asphalt, there should be no difference between them, even if there is, it is only in appearance and volume. However, asphalt mixing plants and asphalt mixing plants are different in even their basic structure and function.
First, let me introduce the basic structure of an asphalt mixing plant, which includes five major components: material supply system, metering system, mixing system, and electrical control system. In comparison, the structure of an asphalt mixing plant is simpler, without so many components, so its operation and maintenance will be simpler.

Asphalt flue gas treatment methods, their principles and characteristics, and an asphalt flue gas environmental protection treatment plan based on the actual asphalt flue gas problems faced by the unit.

1. Basic situation
My unit’s mixing plant is equipped with a 4000-type asphalt mixing plant. During daily production of the asphalt mixing plant, a large amount of asphalt smoke will be emitted from the mixing pot discharge port. This smoke not only has an unpleasant smell, but also contains A large number of compounds that are harmful to the human body, such as benzopyrene, benzanthracene, carbazole and other polycyclic aromatic hydrocarbons, mostly have carcinogenic risks. Smoke overflow will cause pollution to the surrounding atmospheric environment and affect the personal health of workers. Although the overflow port of the mixing station is equipped with a dust retaining wall, the fine dust is seriously raised, and the cold material belt conveyor is dusty. In order to protect the environment, reduce pollution, and reduce cost investment, based on full research and absorption of technology in the same industry, and combined with the actual situation of asphalt mixing, we are planning to install asphalt mixing bag dust collectors to the flue at the discharge port of the mixing pot to control asphalt fumes. Gas is processed. The dust removal efficiency of the bag dust collector can reach 97%~99%, and the dust-containing gas can be purified to a level of 50mg/Nm3.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing plant also needs to be powered on for trial operation before it is officially put into work.
The first step in commissioning is to run a single motor and check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

In order to keep the asphalt mixing plant in a stable operating process, a series of adverse factors related to it must be excluded. What should be paid attention to in this process?
First of all, the selection of the delivery pump in the asphalt mixing plant must meet the requirements of asphalt pouring per unit time during construction, height, and horizontal distance requirements. At the same time, there must be a certain technical and production capacity reserve, and the balanced production capacity is preferably 1.2 to 1.5 times.
Secondly, the movement and hydraulic systems of the asphalt mixing plant must be normal, and there must be no abnormal sound and vibration to avoid large aggregates and lumps inside the equipment, otherwise it is easy to get stuck at the feed inlet of the mixing plant or be blocked due to arching. Another point is that when the asphalt mixing plant is in the same site, it is not suitable to use too many pumps and pumps from multiple manufacturers to avoid affecting its normal operation.

The drive unit is one of the important components of the asphalt mixing plant, so whether it can be reliably operated must be highly valued to avoid adverse effects on the entire asphalt mixing plant. To ensure that the drive unit in the asphalt mixing plant is indeed complete and reliable, the following maintenance measures are essential.
The first thing to pay attention to is the universal rotating part of the drive unit of the asphalt mixing plant. This part has always been a fault-prone part. In order to reduce the occurrence of faults, grease should be added on time, and the wear should be checked frequently, and repaired and replaced in time. Users should also prepare the universal shaft assembly to avoid affecting the working process of the entire asphalt mixer.

Asphalt mixing equipment is also divided into fixed and mobile types. There are still big differences between the two to a certain extent. Let’s take a look at the design of mobile asphalt mixing equipment. What advantages can bring to the equipment?

There is also a reversing valve in the asphalt mixing plant, which generally does not cause problems, so I have not understood its solutions in detail before. But in actual use, we encountered this kind of failure. How should we deal with it?
The failure of the reversing valve of the asphalt mixing station is not complicated, that is, the reversing is not timely, gas leakage, electromagnetic pilot valve failure, etc. The corresponding causes and solutions are of course different. For the reversing valve to not change direction in time, it is generally caused by poor lubrication, the spring is stuck or damaged, oil dirt or impurities get stuck in the sliding part, etc. For this, it is necessary to check the status of the lubricator and the quality of the lubricating oil. Viscosity, if necessary, the lubricant or other parts can be replaced.
After long-term use, the reversing valve is prone to wear of the valve core sealing ring, damage to the valve stem and valve seat, resulting in gas leakage in the valve. At this time, the sealing ring, valve stem and valve seat should be replaced, or the reversing valve should be replaced directly. In order to reduce the failure rate of asphalt mixers, maintenance must be strengthened on a daily basis.

Certain failures cannot be avoided during the use of the asphalt mixing plant. For example, a malfunction of the cold material feeding device may cause the asphalt mixing plant to shut down. This may be due to a malfunction in the asphalt mixing plant or due to gravel or foreign matter being trapped under the cold material belt. If it is stuck, if it is a circuit failure, first check whether the motor control inverter of the asphalt mixing station is faulty and whether the line is connected or open.

Asphalt mixing station is one of the most important equipment in processing operations, so how to build a website has become the focus of people’s attention. The editor has compiled some key points, hoping to be helpful to everyone.

The development prospects of asphalt mixing plants are very good, and the product competition on the market is also very fierce. When the equipment is used, uneven wear of the supporting wheels and wheel rails often occurs, and sometimes there are some abnormal noises and edge gnawing. The main reason is that after the asphalt mixing station has been working for a period of time, the drying cylinder is exposed to high temperature and friction occurs between the supporting wheel and the wheel rail.
Under the action of drying materials in an asphalt mixing station, the equipment will vibrate violently, which will directly lead to improper adjustment of the gap between the wheel rail and the supporting wheel, or mutual interference between the two. The position is skewed, so the operator needs to add grease to the surface contact positions of the supporting wheel and the calibrating wheel rail after every day’s work.

As a special equipment, standardizing the operating procedures of important production tools of asphalt mixing stations, conducting daily maintenance, regular inspections, eliminating hidden dangers, etc. can effectively ensure the safety and stability of the equipment and prevent equipment from malfunctioning due to misoperation. causing equipment damage. Good maintenance operations can also greatly extend the service life of asphalt mixing plants. Therefore, before daily operation, the asphalt mixing plant must be properly maintained to make the asphalt mixing plant operate better and create wealth.

The renovation of the combustion-supporting system of the asphalt mixing plant and the use of DC frequency conversion CNC machining technology are all renovations of the original system. In addition to the above renovation plans, with the existing equipment and personnel, what other measures can be taken in the application to reduce the operating costs of concrete mixing plants?
At present, China has no mandatory national industry standards for heavy residual oil, and the quality of fuel oil varies greatly. Even from the same dealer, the quality difference between batches is very large, and it contains more residues. Therefore, bridge inspection equipment should be installed on the construction site, and professional personnel should inspect various performance parameters of gasoline and diesel to strictly control quality.
When the burner is working, if the flame of the combustion aid is red and the smoke from the ash removal chimney is black, this is the manifestation of poor atomization of gasoline and diesel and insufficient combustion aid. At this time, the following measures should be taken to deal with it: properly adjust the distance between the nozzle and the vortex plate, generally push it inward to a suitable distance, the purpose is to prevent the atomized oil cone sprayed from the nozzle from spraying into the vortex plate; effectively adjust the ratio of gasoline and diesel to gas, so that the gasoline and diesel increase the mass conversion law slowly, or the gas increase the mass conversion law quickly; promptly remove the carbon deposits and coke around the nozzle to prevent the flame from deflecting; heavy residual oil contains more residues, which can easily cause serious damage to the high-pressure oil pump and increase the working pressure, affecting the actual effect of atomization and the shape of the flame, so the high-pressure oil pump must be repaired or replaced in time; install metal filter devices in front of the first and second high-pressure oil pumps, and clean them frequently to prevent the residues in the gasoline and diesel from blocking the nozzle.
The operators should be trained in professional skills on a regular basis to strengthen their job responsibilities and moral education, so that they can establish their respective job responsibilities, understand the importance of their positions, understand the content of their work, and improve their professional level. Skilled operators can properly control the temperature of the asphalt mixing plant mixture to avoid gasoline and diesel waste.
In order to improve the combustion-supporting effect and effectively reduce the operating costs of asphalt mixing stations, Sinoroader Group kindly reminds that the following issues should be noted when using the burner in the asphalt mixing station: To improve the maintenance of the burner, the burner nozzle should be cleaned of charred materials and carbon deposits on the ignition electrode regularly. The nozzle can be disassembled according to the atomization status; the air-oil ratio of the burner is generally not adjusted, and the fuel pump pressure can be adjusted according to the smoke status and the temperature of the asphalt mixture; the sulfur dioxide generated by the combustion of light fuel oil has a strong corrosion to the bag, so the bag should be maintained regularly and the air pressure changes in the bag should be paid close attention to; water deashing will produce more foam, causing the sand settling tank to flow out, so the sand settling tank should be cleaned in time, and a watering design should be carried out to settle the foam; when the steam pressure decreases or the gear oil pump noise increases, the gear oil pump must be replaced.
When the burner is started, the fuel oil circulation system should be completed through the valve, and then the burner control box should be opened to start the burner. If the electronic ignition of the fuel oil fails, you can change the inlet tee and use the diesel engine for ignition. After the ignition is successful for 2 minutes, you can convert it into fuel oil. In this way, even the light fuel oil of lower quality can ensure combustion.

1. Causes of overflow
The main causes of spillage are:
1) Mixing materials in cold silo. Cold material warehouses generally have 5 or 4 warehouses. Each warehouse is required to contain pellets of a certain specification. If cold materials of different specifications are mixed or mistakenly loaded during the loading process, it will cause certain occurrences in a certain period of time. The shortage of pellets of one specification and the overflow of pellets of another specification can easily destroy the supply balance between hot and cold silos.

When we operate the asphalt mixing station, we should heat the equipment half an hour in advance, and the clear tank should be heated for at least two hours; and manually operate each part of the equipment to ensure that it is in good operation. status; it is also necessary to conduct relevant inspections on the valves and manually collect and return oil to ensure that the equipment can operate normally.
Several requirements for safe operation of asphalt mixing plants: