Bitumen Transport Vehicle

The quality of the asphalt mixing plant will be a key factor affecting the quality of the project. After reviewing relevant materials related to the production and construction of asphalt concrete, we summarized some cases of failures in asphalt concrete mixing stations during construction and analyzed the reasons.
1. Unstable output and low production efficiency of asphalt mixing plants
(1) Improper proportioning. The mix ratio of asphalt concrete is divided into target mix ratio and production mix ratio. Among them, the target mix ratio controls the cold material transportation ratio of sand and gravel materials, and the production mix ratio is the mixing ratio of various types of sand and stone materials in the finished asphalt concrete materials specified in the design. The production mix ratio is determined by the laboratory, which directly determines the off-site grading standard of the finished asphalt concrete. The target mix ratio is set to further ensure the production mix ratio, and can be adjusted appropriately during production according to the actual situation. When the target mix ratio or the production mix ratio is not appropriate, the stones stored in each measurement of the asphalt mixing station will be disproportionate, with some overflowing and some other materials, unable to be weighed in time, and the mixing cylinder will be idling, resulting in reduced output.

At present, the production efficiency of asphalt mixing plants in my country’s asphalt construction is far lower than the theoretical efficiency at the time of design. The low efficiency of organic waste gas treatment will not only delay the construction process and cause a waste of resources, but also the quality of the construction will not be very good. guarantee. In the construction of asphalt pavement, the main reasons for the low production efficiency of the asphalt plant are insufficient supply of mixture, resulting in loss of continuity of construction, improper equipment parameter settings, excessive overflow and other problems. Effective measures must be taken to deal with these problems, and ultimately improve production efficiency and ensure construction quality.

Aggregate drying system of asphalt mixer plant

BITUMEN SUPPLY SYSTEM

The driving device is one of the important components of the asphalt mixing plant, so whether it can operate reliably must be highly valued to avoid adverse effects on the entire asphalt mixing plant. In order to ensure that the driving device in the asphalt mixing plant is indeed complete and reliable, the following maintenance measures are essential.

Many people think that since both asphalt mixing plants and asphalt mixing plants are equipment for producing asphalt, there should be no difference between them, even if there is, it is only in appearance and volume. However, asphalt mixing plants and asphalt mixing plants are different in even their basic structure and function.
First, let me introduce the basic structure of an asphalt mixing plant, which includes five major components: material supply system, metering system, mixing system, and electrical control system. In comparison, the structure of an asphalt mixing plant is simpler, without so many components, so its operation and maintenance will be simpler.

Building body frame for asphalt plant

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing plant also needs to be powered on for trial operation before it is officially put into work.
The first step in commissioning is to run a single motor and check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

hot aggregate storage bin system

Natural gas is a colorless, odorless, flammable and explosive gas, the main component of which is methane, which accounts for about 98% of natural gas. The density of natural gas is lower than that of air and it is difficult to liquefy. Natural gas is not only a clean green energy for civil, commercial and industrial use, but also a raw gas for chemical industry. The theoretical ignition value of natural gas is 540 degrees, the combustion temperature is 1970 degrees, the calorific value is 40MJ/m3, and the explosion limit is 5%-15%. CNG refers to natural gas that has been compressed to 20-25MP and stored in high-pressure gas tank trucks, and then transported to various gas transmission points to supply gas to residential users, commercial users and industrial users. In order to ensure the normal operation and safety of the asphalt mixing station and our pressure regulating station, our company has specially formulated the following safety protection measures.

Asphalt mixing plant is a very practical engineering machinery. Especially in the road construction process, it plays an irreplaceable role. Due to its importance, in addition to ensuring its own quality, the use and maintenance of the equipment must be carried out normally. Let’s learn about the daily maintenance requirements of asphalt mixing plants.

The mixing speed of asphalt mixing plant equipment is indeed very fast, and the corresponding mixing power must be very high, but the specific amount must be measured in a certain way to determine the scope of use of asphalt mixing equipment. There are many methods to measure the mixing power of asphalt mixing equipment, but the relatively small errors are the motor counter-torque measurement method and the strain measurement method.
When the motor of the asphalt mixing equipment starts running, the electromagnetic moment acting on the motor rotor and the electromagnetic moment acting on the motor stator are equal, but their directions are opposite. Therefore, as long as the torque acting on the stator is measured, the torque on the rotor can be obtained, and the actual mixing torque is obtained after deducting the friction torque on the rotor bearing.
On the premise of knowing the torque and mixing speed, the mixing power of the asphalt mixing equipment can be calculated. This is the so-called motor counter-torque measurement method, which is relatively simple and suitable for smaller mixing systems.

In general, the development of my country’s asphalt mixing plant industry is very rapid. In the ton segment, it quickly occupied most of the market share. And with the advancement of technology, it can basically meet the current development needs. However, the total demand for some large-scale asphalt mixing plants has not increased or decreased. What are the reasons?
If we analyze from multiple angles, it is not difficult to find that these reasons are also some of the problems faced by my country’s current asphalt mixing plantindustry. These problems are summarized as follows:

In recent years, asphalt concrete, as a new green building material, is gradually being valued by people because of its excellent performance in saving resources, being environmentally friendly, ensuring the quality of construction projects, and achieving sustainable utilization of resources. The development of asphalt concrete fully embodies my country’s policies to achieve energy conservation and emission reduction, and is also an important measure to promote the development of circular economy.

Asphalt mixing plant, also known as asphalt concrete mixing plant, asphalt mixing equipment. Refers to a complete set of equipment used for mass production of asphalt concrete. According to the mixing method, it can be divided into intermittent type and continuous type; according to the transportation method, it can be divided into fixed type, semi-fixed type and mobile type.

The drive unit is one of the important components of the asphalt mixing plant, so whether it can be reliably operated must be highly valued to avoid adverse effects on the entire asphalt mixing plant. To ensure that the drive unit in the asphalt mixing plant is indeed complete and reliable, the following maintenance measures are essential.
The first thing to pay attention to is the universal rotating part of the drive unit of the asphalt mixing plant. This part has always been a fault-prone part. In order to reduce the occurrence of faults, grease should be added on time, and the wear should be checked frequently, and repaired and replaced in time. Users should also prepare the universal shaft assembly to avoid affecting the working process of the entire asphalt mixer.

The core of the asphalt mixing plant is its electronic control system. If it has problems, it will cause a lot of trouble to use. However, in actual use, the electronic control system in the asphalt mixing plant will inevitably encounter some problems and failures. How to solve it at this time?
If only the instrument display of the electronic control system of the asphalt mixing plant is inaccurate, it means that the weighing system may be affected by external forces; or the drift error of the sensor causes the weighing zero position or weighing interval to change; it may also be caused by sensor damage.

In fact, asphalt mixing stations are not uncommon in our daily lives. They are mainly a unit of equipment specially designed to mix asphalt. What we really don’t understand is the gas system of the asphalt mixing station. Only correct maintenance And operation can bring out the best production effect. So what are the faults in the gas circuit of asphalt mixing station?
The following three points are the more common gas path failures of asphalt mixing stations:

Asphalt mixing plant is a relatively important complete set of equipment in people’s lives. There are many components of this equipment, such as grading machine, vibrating screen, belt feeder, powder conveyor, elevator and other parts. Plug valve is one of them, so what is the specific role of plug valve in asphalt mixing plant? This article will give a brief introduction.
The plug valve is first of all a closure or plunger-shaped rotary valve. Generally, it is necessary to rotate 90 degrees to make the channel opening on the valve plug the same as that on the valve body, or to split it to play the role of opening or closing. The shape of the plug valve in the asphalt mixing plant is generally cylindrical or conical.

Oscillating screen. It can screen the heated aggregate according to the design. It requires fully enclosed, double oscillating motor replacement (replacing one substance for another (mostly the strong one takes the place of the weak)) eccentric shaft oscillation, each The layer screen is easy to install quickly. The service life of the drying roller and the power part is not less than 6000h. The roller can fully use heat, the material curtain flows evenly, and the inclination is required to be adjustable.

Asphalt mixing stations and equipment must implement secondary leakage protection measures. They can only be used after being plugged in and operated through the circuit breaker before use. During the trial operation, it is necessary to verify that the rotational speed of the mixing drum will be inappropriate.

In today’s road construction, the use of a large number of road construction machinery represents the entry into the era of highway mechanization. For users, the goal is to use road construction machinery reasonably and tap its potential as much as possible. However, road construction machinery requires various accessories to work together. Now let’s take the asphalt mixing plant as an example to see what commonly used accessories and equipment are available.
Asphalt mixing plant equipment is a relatively complex system, which includes many equipment, mainly nine parts, namely: bag dust removal, finished material temporary storage warehouse, grading machine, fast heating asphalt tank, asphalt barrel removal machine, asphalt recycled material crushing and screening system, coal block crusher, coal mill and dust removal equipment, etc.

With the strengthening of the trend of environmental protection and energy conservation, the environmental protection of asphalt mixing plants has gradually become the mainstream form of mixing plant development. What kind of equipment can be called an environmentally friendly asphalt mixing plant? What are the basic conditions that must be met?
First of all, as an environmentally friendly asphalt mixing plant, it must meet the requirement of using less energy consumption during use. That is to say, under the conditions of the same quantity and quality, less energy is consumed during the operation process, including various resources such as water and electricity.
Secondly, environmentally friendly asphalt mixing plants not only require less energy consumption, but also must achieve higher production efficiency, while also reducing carbon emissions in the entire production process, so as to meet the proposed low-carbon production requirements

At present, most asphalt mixing plants have different degrees of energy loss in use, and these losses have brought us serious waste. How to reduce energy consumption in these aspects and achieve efficient production?
First of all, we must first summarize which aspects have energy loss, and then we can find reasonable solutions based on these problems. Through research, it is found that there are four problems in the use of asphalt mixing plants and the production of asphalt mixtures. The content and measures are as follows:
The first aspect is the management of the pile. We can reduce the energy consumption of the asphalt mixing plant through 3 specific methods: 1. Appropriately reduce the stacking height of the pile; 2. Build an inclined pile site with a good drainage structure; 3. Build a waterproof canopy.

Asphalt mixing equipment has a special function, which is that it can perform cyclic heating to make the asphalt product reach the best condition. But how does it achieve this function? Everyone is curious about this.

Asphalt mixing plants are highly professional equipment with complex systems. It is inevitable that some failures will occur during use. So, what are the common hardware failures of asphalt mixing plants? Do you know?
(I) Because its system is relatively complex, when different components have problems, the problems caused may be different. If during the operation, it is found that the material addition of each silo is inaccurate, this problem may be due to the failure of the sensor of the asphalt mixing plant. At this time, the machine should be stopped for inspection and replaced with a new sensor if necessary. It may also be caused by the jamming of the scale bar. At this time, foreign objects should be removed in time.

The actual operation steps of drying drum of asphalt mixing equipment: 1. Pay attention to routine inspection; 2. Proper operation steps; 3. Effective maintenance.
Drying drum is a cylindrical device specially used for heating and drying stones in asphalt mixing equipment. Proper application and maintenance of drying drum can maximize the performance of drying drum, increase its service life and reduce application cost. Let’s take a look at the actual operation steps below.
1. Pay attention to routine inspections
The asphalt mixing equipment drying drum has been tested and inspected before leaving the factory, but it will be subjected to vibration and vibration during transportation to the construction site. A comprehensive inspection should be carried out before use: check whether all anchor bolts are tightened; whether all key pins are properly driven; whether all drive devices are adjusted according to the manufacturer’s instructions; whether all pipe connections are appropriate and whether the three-way joints are reliable; whether the entire equipment is fully lubricated; start the motor and check whether all parts can rotate steadily in the correct rotation direction; whether the pressure gauge can work normally and whether the valve is adjusted to the correct working pressure; whether the burner ignition mechanism is available and whether the gate valve is open.
2. Correct operation steps
After the equipment is started, it is recommended to control the machine manually at the beginning, and then switch to the automatic control mode after achieving the required production volume and pouring temperature. The stone should be dried and have a stable moisture content as much as possible so that the stone can maintain a stable final temperature when passing through the drying drum. If the stones delivered to the drying drum change frequently and the moisture content changes each time, the burner should be adjusted frequently to compensate for these changes.
The stones directly from the crushed stone have a relatively constant moisture content, while the stones from the outdoor storage yard have a higher moisture content, and the moisture content of different piles varies greatly. Therefore, it is best for the stones to come from the same source.

The asphalt plant control room is used to control the asphalt material and working mode