Sinoroader shares bitumen melting equipment with you

The container-type emulsified bitumen equipment hot-melts the base cold-mix colored bitumen and disperses it through the equipment into small cold-mix colored bitumen particles in an aqueous solution containing emulsifier to form a liquid cold-mix colored bitumen material.

Asphalt spreader is used to spread the penetration oil, waterproof layer and bonding layer of the bottom layer of asphalt pavement of high-grade highway. It can also be used for the construction of county and township highway oil roads with layered paving technology. It consists of a car chassis, an asphalt tank, an asphalt pumping and spraying system, a thermal oil heating system, a hydraulic system, a combustion system, a control system, a pneumatic system, and an operating platform.
Knowing how to properly operate and maintain the asphalt spreader can not only extend the service life of the equipment, but also enable the construction project to proceed smoothly. So what problems should the asphalt spreader pay attention to when working? The technicians of Gaoyuan Road Construction Machinery Equipment Co., Ltd. give you tips:
1). Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreader, check the four thermal oil valves and the pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Test the asphalt pump and circulate for 5 minutes. If the pump head shell is hot, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not turn or make noise. In this case, the valve needs to be opened to continue heating the asphalt pump until it can operate normally. During the working process, the asphalt liquid must be kept at a working temperature of 160~180℃, and it cannot be filled too full (pay attention to the liquid level pointer during the injection of asphalt liquid, and check the tank mouth at any time). After the asphalt liquid is injected, the filling port must be closed tightly to prevent the asphalt liquid from overflowing during transportation.
2). During use, asphalt may not be pumped in. At this time, it is necessary to check whether the interface of the asphalt suction pipe is leaking. When the asphalt pump and pipeline are blocked by solidified asphalt, a blowtorch can be used for baking, and the pump must not be forced to turn. When baking, care should be taken to avoid directly baking the ball valve and rubber parts.
3). When spraying asphalt, the car should be driven at a low speed. Do not step on the accelerator hard, otherwise it may cause damage to the clutch, asphalt pump and other components. If 6m wide asphalt is spread, pay attention to obstacles on both sides at any time to prevent collision with the spreading pipe. At the same time, the asphalt should be kept in a large circulation state until the spreading work is completed. After the work is completed every day, if there is any remaining asphalt, it must be returned to the asphalt pool, otherwise it will solidify in the tank and cannot work next time.
4). In addition, the emulsifier must also pay attention to daily maintenance:
1. The emulsifier and delivery pump and other motors, agitators, and valves should be maintained daily.
2. The emulsifier should be cleaned after work every day.
3. The speed regulating pump used to control the flow should be regularly tested for accuracy, and adjusted and maintained in time. The asphalt emulsifier should regularly check the matching clearance between its stator and rotor. When the minimum clearance specified by the machine cannot be reached, the stator and rotor should be replaced.
4. If the equipment is out of use for a long time, the liquid in the tank and pipeline should be emptied (the emulsifier aqueous solution should not be stored for a long time), the hole covers should be tightly closed, kept clean, and the running parts should be filled with lubricating oil. When it is used for the first time or when it is used again after a long period of inactivity, the rust in the tank should be removed, and the water filter should be cleaned regularly.
5. Regularly check whether the terminal in the electric control cabinet is loose, whether the wires are worn during shipment, and remove dust to avoid damage to the machine parts. The frequency converter is a precision instrument. Please refer to the instruction manual for specific use and maintenance.
6. There is a heat transfer oil coil in the emulsifier water solution heating stirring tank. When injecting cold water into the water tank, the heat transfer oil switch should be turned off first, and then the switch should be turned on to heat after adding the required amount of water. Pouring cold water directly into the high-temperature heat transfer oil pipeline can easily cause the weld to crack.

All kinds of base layers have the problem of strength formation and growth (Emerson). The strength is gradually generated during the curing process, and the internal structure will become more and more dense. The test shows that when the semi-rigid base layer is sprayed with penetration oil before the cement (material: powdered water-hardening inorganic cementitious material) has not yet hardened, the penetration depth is deep; with the increase of age and strength, the penetration effect of the penetration oil is getting worse and worse.
At the same time, timely spreading of penetration oil has a good retention effect on the moisture in the base layer, preventing the evaporation of moisture, ensuring the formation of the strength of the base layer, and the surface of the base layer is not easy to loosen. The penetration oil also protects the semi-rigid base layer from cracking due to exposure to the sun. Furthermore, since the base layer is no longer covered and watered for curing, the temperature inside the base layer is high, which is conducive to the growth of strength.

Bitumen emulsifier is a surfactant. A surfactant is a compound that reduces the surface tension between two liquids, a gas and a liquid, or a solid and a liquid. Surfactants are mainly used in: detergents, detergents, fabric softeners, wetting agents, emulsifiers, foaming agents, dispersants, adhesives, etc.

Emulsified asphalt is an emulsion that disperses asphalt into the water phase to form a liquid at room temperature. This determines that emulsified asphalt has many technical and economic advantages over hot asphalt and diluted asphalt. We know that modified asphalt equipment is a road engineering machinery. In order to better promote users’ understanding of it, today the editor will introduce its characteristics to you so that users can better understand that modified asphalt equipment is used for modified asphalt. It consists of a main machine, a modifier feeding system, a finished product tank, a heat transfer oil reheating furnace and a microcomputer control system. The main machine is equipped with a mixing tank, a dilution tank, a colloid mill and an electronic weighing device. The entire production process is controlled by a computer automatic program. In addition, it can be learned that the product has the advantages of reliable quality, stable performance, accurate measurement, and convenient operation. It is an indispensable new equipment in highway construction. The advantages of asphalt equipment are prominently reflected in its two-way modification effect, that is, while greatly increasing the softening point of asphalt, it also significantly enhances the low-temperature ductility, improves the temperature sensitivity, and has a particularly large elasticity and recovery rate. The modified asphalt equipment has a long service life and a safe and reliable production process. The rotor and stator are specially heat treated, and the service life of the equipment is more than 15,000 hours.

In the cold winter, you need to pay attention to the following points when using asphalt melting equipment:
1. Protection from cold and warmth: The equipment needs to be operated indoors or in a place with shading facilities, and ensure that the temperature of the equipment and the surrounding environment is maintained within an appropriate range.
2. Check the equipment: Before use, the equipment should be checked, including whether the circuits, fluid circuits and other parts of the equipment are working normally, and whether there are any leaks of electricity or water in the equipment.
3. Pay attention to safety: During operation, you should wear protective equipment and avoid direct contact with hot asphalt. At the same time, it is necessary to avoid equipment overload operation and prevent equipment damage and safety accidents.
4. Control speed: Reasonably control the working speed of the equipment according to weather conditions and road conditions to avoid overheating of the equipment, causing asphalt to flow too quickly or burn.
5. Storage conditions: When not in use, place the device in a dry, ventilated place with moderate temperature, and ensure that any residue in the device is completely removed.

Asphalt sealant is a material specially used for road crack repair. The following is a detailed introduction to asphalt sealant:
1. Definition and composition
Asphalt sealant is a road repair material made of asphalt or modified asphalt as the base material, with a certain amount of additives and fillers added, and processed by special technology. It usually has a black or dark brown appearance and is in a solid or semi-solid form.
2. Main characteristics
High adhesion: Asphalt sealant can firmly bond to the crack wall of the road surface to form a tight sealing layer to prevent moisture and other harmful substances from invading the road surface structure.
High elasticity: It has a certain elastic recovery ability and can adapt to the expansion and contraction changes of the road surface to prevent further expansion of cracks.
Weather resistance: After special process treatment, it has good weather resistance and can maintain its stable performance for a long time.
Convenient construction: The construction operation is simple and fast, without complex construction machinery, which reduces the construction cost.
3. Scope of application
Asphalt sealant is widely used in crack repair of various asphalt pavements, including highways, urban roads, airport runways, etc. At the same time, it can also be used for the maintenance and repair of asphalt surfaces such as bridges, tunnels, and parking lots.

The emulsified bitumen equipment hot-melts the base cold-mix colored bitumen, and then disperses the slightly cold-mixed colored bitumen particles into the aqueous solution containing emulsifier through a machine to form liquid cold-mixed colored bitumen sheets.

Colored asphalt pavement is a kind of special pavement material that mixes colored particles into asphalt and then lays on the pavement

According to the configuration, layout and controllability of bitumen melting equipment, bitumen melting plant can be divided into three types: mobile, transportable and portable. What should be paid attention to in the production of bitumen melter equipment of different sizes? Let’s learn about it below!
Bitumen melting plant is to fix the demulsifier mixing equipment, black anti-static tweezers, asphalt pump, automatic control system, etc. on a special support chassis. Because the bitumen melter equipment can directly change the production site, it is suitable for the production of emulsion bitumen in construction sites with decentralized projects, small usage and frequent movement.
The main components of the bitumen melting equipments are installed in one or two 60 standard containers. The bitumen melting plant is loaded and transported separately to complete the relocation of the construction site. With the help of asphalt melting equipments hoisting equipment, it is quickly installed and put into operation. Such bitumen melter plant has large, medium and small different configurations, which can meet different project requirements.

Analysis of the necessity of emulsified bitumen equipment in modern road construction projects With the acceleration of the construction speed of transportation infrastructure, the construction standards are getting higher and higher, and higher requirements are also put forward for the use of emulsified bitumen in the closed layer of fly ash and the adhesive layer between the new and old ground.

During the use of emulsified bitumen equipments, if maintenance is not paid attention to, the cycle will be short, and problems will often occur during use. Only by doing a good job of maintenance can the operation efficiency of the equipment be improved. For example, during maintenance, the following points must be grasped.
It is necessary to regularly check the wear condition of the internal structural components of the mechanical equipment, such as the core feed pipe, the rough jaw plate on the impeller, the cone cap, the wear level of the jaw plate, the rain shield on the circle, and the wear condition. If the wear is more serious, it is necessary to replace or repair it in time. When replacing, it is also necessary to pay attention to the model and specifications, and replace it according to the original components as a reference.

Asphalt spreading truck is a kind of black ground construction machinery. It is an important equipment in the logistics construction of roads, municipal roads, airports and ports. This equipment is mainly used to spray different types of asphalt on the ground to meet the construction requirements of different levels of ground oil permeable layer, sticky layer, left and right permeable layer, fog permeable layer, etc.

Emulsified asphalt is an aqueous suspension of asphalt particles with high interfacial energy. This suspension state is thermodynamically unstable and has the potential to reduce its interfacial area (i.e., through the coagulation process) to a stable state. Preventing this coagulation state (dispersion destruction) is the stabilization effect of the emulsifier protective layer. The stability of emulsified asphalt refers to the ability of asphalt particles to aggregate and cause phase separation, and also refers to the time required for emulsified asphalt to reach equilibrium. That is, the time for asphalt particles to aggregate and separate from water. How can we increase this time? How to prevent emulsified asphalt from demulsifying?

Emulsified modified asphalt equipment includes sewage treatment, water storage tank, water metering and verification temperature control system, asphalt storage tank, asphalt external temperature control system, hot water pump soap seasoning system, soap storage tank, soap mixing pump, soap external temperature control system and metering and verification system, filter, hot asphalt mixing pump and metering and verification system, pipeline black anti-static tweezers, emulsified asphalt cooling system and retrieval equipment, product tank and electrical control system.
The whole set of procedures is modularized, and customers can freely match and use according to their needs. The application of each part of the equipment is as follows: Sewage treatment system: Mechanically filter and adsorb the general drinking water to react with epoxy resin to convert the strong drinking water into pure softened water, reduce the water holding capacity, and improve the emulsion effect of asphalt or asphalt concrete.

Road repair Keep the road to maintain the performance of the road, restore the damaged part in time, ensure the safety, comfort and smooth driving, save transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time. With the performance, the damaged part is restored in time to ensure the safety, comfort and smooth driving, saving transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time.

We need to prepare a lot of work when using modified asphalt equipment. What kind of work do we need to prepare? Next, let me briefly introduce the relevant knowledge points.
1. Heat transfer oil heats and insulates the modified asphalt equipment and nozzle. After spraying, the asphalt pump and nozzle do not need to be cleaned with diesel. Use high-pressure air to press the asphalt in the pipeline and spray pipe back to the tank, and then blow the nozzle; use heat transfer oil to keep warm, so that the pipeline and nozzle are smooth and unobstructed. 2. Various asphalts can be spread: high-viscosity asphalt, hot asphalt, emulsified asphalt, etc.; the spreading width can be freely adjusted, each nozzle can be controlled separately, and the maximum spraying width is up to 6m. Flexible handheld spray guns can be used to spray asphalt on corners. 3. Excellent thermal insulation performance, average cooling ≤1-2℃/h. 4. Convenient loading and unloading function. In addition to filling asphalt from the asphalt tank port, hot asphalt can be sucked out by itself, and external asphalt can also be pumped and transferred. 5. The modified asphalt equipment is evenly spread, and the nozzle design can be used for triple overlapping spraying.
The above are the relevant knowledge points of modified asphalt equipment. I hope the above content can be helpful to everyone. Thank you for your viewing and support. More information will be sorted out for you later. Please pay attention to our website updates.

The selection of asphalt melting equipment should take into account factors such as the use environment, working conditions, and technical requirements. Common ones include hot oil heating equipment, electric heating equipment, and gas heating equipment.
Hot oil heating equipment is suitable for occasions that require long-term heating and high temperature control accuracy;
Electric heating equipment is suitable for small projects or occasions where temperature control accuracy is not required;
Gas heating equipment has the advantages of simple operation and low cost, but safety protection measures must be strictly followed.
When choosing, it is also necessary to comprehensively consider factors such as economy and environmental protection.

When performing bitumen melting, specialized equipment is required. These equipment usually include bitumen melting furnaces, asphalt mixers, asphalt conveying equipment, etc. Among them, the bitumen melting furnace is one of the most advanced equipments, which can heat solid bitumen to liquid state. In addition, asphalt mixers can mix liquid asphalt with stone to make asphalt concrete. , Asphalt conveying equipment can transport asphalt concrete to the construction site. The selection and use of these equipment are of great significance to ensure the quality of bitumen melting and construction efficiency.

From the current point of view, road construction machinery has bottomed out and asphalt meltering equipment has risen rapidly. In recent years, highway construction and maintenance departments have a strong awareness of using asphalt mixing equipment, especially in developed coastal areas such as Beijing, Shanghai, Jiangsu, Zhejiang, etc. In addition, these regions have a fast economic growth rate, relatively developed industry, and strong comprehensive economic strength. Therefore, the consumption of asphalt mixing equipments in these regions has always been at the forefront of the country. With the rapid development of highway construction and the increase in demand for asphalt, barreled asphalt has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported asphalt used in high-grade highways is in barrel form, which requires an asphalt meltering equipment with fast melting speed, clean de-barreling, and can prevent asphalt aging. my country’s highway construction has achieved remarkable results, among which mechanized production has contributed greatly. Different types of asphalt mixers and bitumen meltering equipment are selected for the characteristics of large highway pavement construction and tight construction period. With the rapid development of my country’s economy, the further extension of expressways, and the large-scale development of western construction, the central and western regions have become new investment hotspots. While paying attention to the market in the developed eastern regions, domestic road construction machinery manufacturers have also increased their efforts to develop the central and western markets, creating new highlights for the domestic asphalt mixing plants consumer market. In summary, my country’s asphalt mixing plant sales market has begun to move westward with the westward movement of investment hotspots. As the market center of gravity gradually shifts westward, the market in the western region is gradually heating up. The self-heating integrated structure, hot air barrel melting and bitumen barrel flipping technology in the asphalt barrel removal equipment are our company’s self-heating integrated structure. The thermal oil furnace used in the old equipment is perfectly integrated with the asphalt barrel removal equipment body, which reduces the volume of the entire set of equipment, greatly reduces equipment investment, saves equipment space and transfer transportation costs.

Contemporary roads and pavements have undergone many changes: traffic volume and driving frequency have increased significantly, the axle load of logistics trucks has continued to increase, one-way driving in separate lanes has been widely implemented, and regulations have further improved the anti-flow resistance of the ground, that is, the work of modified asphalt equipment under high temperatures ability;

Modified (rubber powder) bitumen equipment, one of the road maintenance equipment. It is a kind of equipment that measures, mixes and develops SBS, rubber powder and asphalt.
Modified (rubber powder) bitumen equipment is a set of wet modification processing technology, which mainly consists of modified material metering and promotion, bitumen rapid heating, asphalt metering, high-intensity mixing tank, mixed material transfer pump, development tank, colloid mill, Control system and other components.

Working conditions of asphalt debarreling equipment:
(1) Outdoor temperature: 20°C (average temperature of day and night)
(2) Heat exchange oil: 320 ℃
(3) Loading time is not included (because the personnel equipped in each unit are different, so the loading time is also different)
(4) There is no fluctuation in oil temperature (optimal automatic burner)
(5) The working temperature of the oil furnace is 220-260 ℃
(6) The flow rate of the oil circulation pump is not less than 50m3/h traffic
(7) When the outdoor temperature is lower than 20℃, the output decreases. The lower the temperature, the lower the output, and the higher the temperature, the higher the output.
(8) The greater the deformation of the asphalt barrel, the greater the impact on the output

The requirements for SBS asphalt emulsification equipment are very high. The micro powder machine must have a sufficiently large driving force and can bear the condensation type. Because the temperature requirements of the emulsion SBS asphalt process are relatively high, the emulsified asphalt should be passed through a heat exchanger before feeding to reduce the emulsified asphalt temperature to below 90°C to prevent the emulsified asphalt from breaking due to excessive temperature.
The application scope of SBS modified emulsified asphalt is very wide. According to the nature of the construction, it can be used in new construction, renovation, and reconstruction projects; according to the nature of the project, it can be used in overhaul, equipment overhaul, and maintenance projects. Among them, the actual application projects include micro-surfacing, cold regeneration, cold mixing and cold paving, adhesive layer, permeable oil, slurry seal, gravel permeable layer, fog permeable layer, road moisture-proofing, SBS membrane, ground seam filling, and all other projects that can use emulsified asphalt.

Some of the equipment of emulsified modified bitumen equipment are as follows. The specially made bitumen filter can effectively filter the residues and dirt in the high-temperature culture medium bitumen to avoid damage to the subsequent equipment. The emulsified modified bitumen equipment adopts a spiral plate type or a shell and tube heat exchanger to quickly heat the culture medium bitumen through high-temperature heat transfer oil to meet the needs of the production process. The emulsified modified bitumen equipment is heated in the storage tank to prevent the bitumen from aging due to long-term high-temperature heating and exposure to the air. The sulfate generated during the production process of the emulsified modified bitumen equipment is very limited, reducing air pollution.
The emulsified modified bitumen equipment sends the modified material manually poured into the dumping bin to the bitumen batching tank by wind or spiral. It can be equipped with a metering and calibration system. The emulsified modified bitumen equipment thickener is automatically or manually added. The emulsified modified bitumen equipment can be equipped with a metering and calibration system. Emulsified modified bitumen equipment transportation and metering and calibration system, the emulsified modified bitumen equipment adds the set bitumen amount to the batching tank through the frequency converter and computer interlock. The emulsified modified bitumen equipment and bitumen steam flowmeter use big brand products to ensure the preparation.

The modified asphalt equipment produced by Sinoroader can produce SBS, rubber powder, SBR, and PE modified asphalt manually and automatically. Some of its configurations and uses are as follows:
1. Filter: The specially made asphalt filter can effectively filter impurities and foreign matter in the high-temperature matrix asphalt to prevent damage to subsequent equipment.
2. Matrix asphalt heater: The spiral plate or shell and tube heat exchanger is used to quickly heat the matrix asphalt through heat transfer oil to meet the needs of the production process. Heating in a sealed tank avoids the aging of asphalt due to long-term high-temperature heating and exposure to the air. The sulfide produced during the production process is quite limited, reducing environmental pollution.
3. Modifier air delivery or spiral addition system: The modifier manually poured into the pouring hopper is delivered to the asphalt batching tank by wind or spiral. It can be equipped with a metering system.
4. Stabilizer automatic or manual addition system: It can be equipped with a metering system.

Emulsified asphalt equipment is an indispensable equipment in road construction and one of the basic equipment for waterproof coatings. What are the components of emulsified asphalt equipment? Today, we will explain the various parts of emulsified asphalt equipment in detail.
Required parts
Asphalt pump: a device for supplying asphalt to the colloid mill.
Emulsion pump: a device for supplying emulsion to the colloid mill.
Colloid mill: a device for mixing, homogenizing and emulsifying asphalt and emulsion.
Control system: a device for controlling the flow of asphalt and emulsion, and the start and stop of various pumps.
Emulsion blending: a device for mixing water, emulsifiers and other additives.
Water heating part: a device for heating water.

Conventional pit repair techniques are mainly hot material repair and cold filling repair, and warm mixing technology is used to ensure compaction, while there are also some special repair methods such as slurry seal/micro-surface material repair

Fillers used in emulsion bitumen equipment are generally divided into two types: chemically active and non-chemically active. In the production of emulsion bitumen equipment, it can improve the stability of the slurry mixture, speed up or slow down the demulsification speed, and improve the strength of the sealing layer. When adding chemically active fillers, the reaction and compatibility of the fillers with mineral materials and modified emulsion bitumen should be fully considered.