Six characteristics of synchronous chip seal technology, how many do you know?

Everyone has a side of themselves that they don’t want others to know. As a preventive road maintenance technology, slurry sealing has some shortcomings. do you think so?
Slurry seal is a kind of road protection that uses special equipment to mix emulsified asphalt, water, additives, aggregates, fillers and other ingredients in a certain proportion, and then mixes the slurry mixture onto the original road surface to form a thin layer. Maintenance technology. These are all well known. The editor will not go into details on this.

During the use of emulsified bitumen equipments, if maintenance is not paid attention to, the cycle will be short, and problems will often occur during use. Only by doing a good job of maintenance can the operation efficiency of the equipment be improved. For example, during maintenance, the following points must be grasped.
It is necessary to regularly check the wear condition of the internal structural components of the mechanical equipment, such as the core feed pipe, the rough jaw plate on the impeller, the cone cap, the wear level of the jaw plate, the rain shield on the circle, and the wear condition. If the wear is more serious, it is necessary to replace or repair it in time. When replacing, it is also necessary to pay attention to the model and specifications, and replace it according to the original components as a reference.

The slurry sealer is a special equipment for road maintenance that we see in our lives. The slurry sealer is mainly used to deal with the decrease in surface wear resistance, cracks, etc. of the road, to improve the waterproofness and skid resistance of the road surface, thereby greatly improving the driving comfort and flatness inside, so as to achieve a new effect for the road surface. So what is the operation process of the slurry sealer?
Before starting the slurry sealer, you should be prepared to test the quality of the slurry sealer materials before construction. One of the most important points is to certify and inspect whether the content of emulsified asphalt can meet the requirements of the specification, and the mixture should also meet the requirements. After confirming the measurement standards, check that the road surface to be constructed should be dry, free of debris, water, flat, etc.

Bitumen decanter equipment can be placed in a complex system as an independent unit, replacing the existing heat source de-barreling method, or in parallel as a core component of a large set of equipment, or it can work independently to meet the requirements of small-scale construction operations.
The Sinoroader bitumen decanter device is mainly composed of a de-barreling box, a lifting mechanism, a hydraulic thruster and an electrical control system. The box is divided into two chambers, the upper chamber is a barreled bitumen melting chamber, and heating coils are evenly distributed around it. The heating pipe and the bitumen barrel mainly exchange heat in a radiation manner to achieve the purpose of bitumen de-barreling. Several guide rails are the tracks for the bitumen barrel to enter. The lower chamber is mainly to continue heating the bitumen removed from the barrel to make the temperature reach the suction pump temperature (100℃), and then the asphalt pump is pumped into the upper chamber. At the same time, an empty barrel is pushed out at the rear end outlet. There is also an oil tank on the platform at the entrance of the asphalt barrel to prevent the dripping bitumen from flowing out.
The inlet and outlet doors of the device adopt a spring automatic closing mechanism. The door can be automatically closed after the asphalt barrel is pushed in or out to reduce heat loss. A temperature gauge is installed at the asphalt outlet to observe the asphalt outlet temperature. The electrical control system can control the opening and closing of the hydraulic pump and the reversing of the electromagnetic reversing valve to realize the advance and retreat of the hydraulic cylinder. If the heating time is extended, a higher temperature can be obtained. The lifting mechanism adopts a cantilever structure. The bitumen barrel is lifted by an electric hoist, and then moved horizontally to place the bitumen barrel on the guide rail. A temperature gauge is installed at the outlet of the asphalt meltering equipment to observe its outlet temperature.

Bitumen emulsion equipment is widely used in new technologies and new processes for preventive maintenance. Bitumen emulsion plant is an emulsion at room temperature formed by dispersing bitumen into the water phase. It is a new material that is made of natural materials. It is different from traditional Compared with hot bitumen, it saves more than 50% of energy, saves 10%-20% of bitumen, and causes less pollution.

What key points should be paid attention to when feeding emulsified asphalt equipment? When it comes to emulsified asphalt equipment, I don’t know how much you know about it? What should you pay attention to when adding materials?
The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

No matter what product is used, after using it for a period of time, some large and small problems will inevitably arise, which will affect our work, just like the use of asphalt heating equipment will cause problems such as uneven asphalt pavement. We know that for the use of asphalt heating equipment, the construction of asphalt pavement is affected by many factors, including the quality of construction personnel, the quality of roadbed construction, the treatment of the two sections of the bridgehead culvert and the expansion joint of the bridge, the construction of the road subbase and base, the selection of road construction machinery and the quality of road materials. These are the main reasons affecting the flatness of the road surface.
In order to better help customers apply it, professionals introduce the use of asphalt heating equipment. Flatness is an important indicator for measuring the quality of high-grade pavement. Unsmooth pavement will increase driving resistance and cause additional vibrations in the vehicle, which will directly affect the safety and comfort of driving. At the same time, it will aggravate the damage of automobile parts and tires and increase fuel consumption.

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

The viscosity of the drum bitumen decanter equipment decreases as the temperature increases during the production process. Its output viscosity is about twice as high as every 12°C increase. During production, the base bitumen decanter equipment must first be heated to a liquid state and then emulsified. In order to better integrate the emulsification ability of colloid milling, the viscosity of base bitumen decanter is generally controlled to be about 200 cst. The lower the temperature, the higher the viscosity, which increases the pressure on the bitumen decanter pump and colloid milling, making emulsification impossible: However, on the other hand, in order to prevent the bitumen decanter equipment from weaning when the moisture of the finished product evaporates, it is impossible to heat the base asphalt barrel removal temperature too high, and generally use a colloid grinding inlet and outlet system. The finished product temperature should be below 85°C.

Emulsified asphalt is an aqueous suspension of asphalt particles with high interfacial energy. This suspension state is thermodynamically unstable and has the potential to reduce its interfacial area (i.e., through the coagulation process) to a stable state. Preventing this coagulation state (dispersion destruction) is the stabilization effect of the emulsifier protective layer. The stability of emulsified asphalt refers to the ability of asphalt particles to aggregate and cause phase separation, and also refers to the time required for emulsified asphalt to reach equilibrium. That is, the time for asphalt particles to aggregate and separate from water. How can we increase this time? How to prevent emulsified asphalt from demulsifying?

Asphalt melting equipment is a mechanical equipment specially used to heat and melt asphalt. Our company’s products have been widely recognized and applied in the market.
Our main production process is: transporting the high-temperature oil and gas generated after high-temperature cracking of raw materials (such as petroleum) in the combustion chamber to high-speed rotating heat-conducting oil tankers for heat transfer, melting, cooling and other processes, and finally obtaining the required finished materials or Semi-finished materials. The advantage is that it can make the best use of raw materials and reduce energy consumption; at the same time, it can also customize products of different specifications according to different needs to meet the different requirements of customers. In addition, we provide after-sales service and technical support to protect the interests and safety of our customers.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing station also needs to be powered on for trial operation before it is officially put into work.

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.
For the block asphalt melting equipment, the Provincial Environmental Protection Department will review the application materials, and appoint the Provincial Block Asphalt Melting Equipment Management Office to organize relevant doctors to conduct technical evaluation and on-site technical evaluation, and produce expert technical evaluation opinions and on-site inspection reports. Then report the materials of the block asphalt melting equipment to the meeting of directors for scientific research and make a review decision.

There are many types of emulsified bitumen, and PC-2 is one of them, which is a spray-type emulsified bitumen. It is used for spraying oil through the base layer of granular materials and health care spraying on semi-rigid base layers. There is also the PA-2 type, which has the same purpose as the PC-2 type. The difference is that the PC-2 type is a cation, while the PA-2 type is an anion.

As technology becomes more and more advanced, we use more and more equipment in our lives, and the functions are also very complete. Synchronous crushed stone seal is also a product used in many places. After continuous improvement and development, it has many functions. Next, we will introduce to you the problem of preventive maintenance of synchronous crushed stone seal? If you want to know, you can read it together.

All kinds of base layers have the problem of strength formation and growth (Emerson). The strength is gradually generated during the curing process, and the internal structure will become more and more dense. The test shows that when the semi-rigid base layer is sprayed with penetration oil before the cement (material: powdered water-hardening inorganic cementitious material) has not yet hardened, the penetration depth is deep; with the increase of age and strength, the penetration effect of the penetration oil is getting worse and worse.
At the same time, timely spreading of penetration oil has a good retention effect on the moisture in the base layer, preventing the evaporation of moisture, ensuring the formation of the strength of the base layer, and the surface of the base layer is not easy to loosen. The penetration oil also protects the semi-rigid base layer from cracking due to exposure to the sun. Furthermore, since the base layer is no longer covered and watered for curing, the temperature inside the base layer is high, which is conducive to the growth of strength.

We have conducted in-depth research on asphalt distributors and have accumulated a lot of production technology experience. We have conducted professional and in-depth research on some problems existing in the market to provide convenience for everyone in future production applications.
Every time when spraying asphalt, the asphalt distributor does not spray asphalt. Troubleshooting. The asphalt distributor does not spray asphalt. It is a common fault. The following teaches you how to solve the problem of not spraying asphalt.
1. No asphalt spraying
Analysis of the reasons may be the following reasons:
1. Is the asphalt pump working?
2. Are the valves adjusted correctly?
3. Is the pump or pipeline blocked?
2. Troubleshooting method
1. Check whether the hydraulic system is working properly?
2. After adjusting the valve position, the asphalt distributor must be cleaned to avoid pipeline blockage when used next time. Because the asphalt distributor has different high and low configurations, it can spread various high-viscosity and high-temperature modified asphalts and rubber asphalt in high configuration. If you mistakenly use a low-configuration asphalt truck to spread this type of asphalt, you must spray the asphalt inside the entire vehicle clean after the first use. After spraying, in order to leave no residual asphalt, you can use waste diesel to clean it. Our company’s vehicles are equipped with air cleaning and gravity cleaning devices. Diesel cleaning is a reliable cleaning method.

Emulsified asphalt equipment is a special equipment for producing emulsified asphalt. The emulsified asphalt produced by emulsified asphalt equipment is used in many industries. I wonder how much you know about the emulsified asphalt produced by emulsified asphalt equipment. Let’s take a look at them one by one:
Slurry seal is a cold mix asphalt mixture with the advantages of aggregate and asphalt mixing. Under normal circumstances, similar graded slurry seal has a higher modulus than hot mix asphalt mixture, so it is often used to fill road rutting. The higher stability has a higher resistance to deformation. The mixture is usually composed of harder fine aggregate grading and wear-resistant aggregate with high sand equivalent, especially micro-seal and polymer-modified seal. This greatly increases the strength and integrity of the road surface. This makes the road surface have high wear resistance and excellent deformation resistance. Emulsified asphalt emulsion is also easy to use on a mobile slurry seal paver, where mixing and admixtures are used for chemical control to meet maintenance needs.

The emulsified bitumen equipment hot-melts the base cold-mix colored bitumen, and then disperses the slightly cold-mixed colored bitumen particles into the aqueous solution containing emulsifier through a machine to form liquid cold-mixed colored bitumen sheets.

To ensure good operation of asphalt melting equipment and extend its service life, regular maintenance and repairs are required. The following are specific maintenance and repair steps:
First, various parts of the equipment, including heating elements, pipes, valves, etc., need to be inspected regularly to make sure they are not worn or damaged. If any problems are found, they should be repaired or replaced immediately.

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

Road repair Keep the road to maintain the performance of the road, restore the damaged part in time, ensure the safety, comfort and smooth driving, save transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time. With the performance, the damaged part is restored in time to ensure the safety, comfort and smooth driving, saving transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time.

Synchronous sealing trucks play an important role in road maintenance. Daily maintenance of synchronous sealing trucks is an important part of ensuring the good operation of the equipment and extending its service life. Here are some common maintenance measures:

When using asphalt melting equipment, you need to pay attention to the following points:
1. The power must be cut off during installation and operation to ensure safety.
2. Before starting operation, check whether all components are normal and have no fault prompts. In particular, the inspection of key parts such as the heater part and the conveyor belt device is particularly important.

Whether it is the application of modified asphalt equipment or the application of other equipment, if you want to extend its service life, you need to do daily maintenance work. In order to better help everyone, we have modified asphalt The maintenance methods that can be adopted when using the equipment are introduced as follows:

Modified asphalt equipment is a widely used asphalt equipment. Now its ultra-high performance has been widely praised by users. However, we must first ensure the safe use of modified asphalt equipment in order to fully demonstrate its performance. So how much do you know about the safe use and operation of modified asphalt equipment? Today, Gaoyuan Road Construction will explain it in detail:
1. Placement: The modified asphalt equipment should be placed on a flat place, and the front axle wheel should be fixed with sleepers and the tires should be suspended to ensure that the machine does not move around during operation.
2. Check regularly whether the mixer blades are deformed and whether the screws are loose.
3. Check whether the running direction of the mixing barrel is consistent with the arrow. If not, please replace the positive and negative poles of the wiring.
4. Before powering on, check for empty vehicle trial operation, check for leakage, and check the idling of the mixing barrel. The normal speed is about 3 times faster when the empty vehicle is full. If the speed is wrong, you should stop and check.
5. If the machine is stopped for more than one hour after the asphalt mixing is completed, clean the mixing barrel, pour in clean water, and clean the mortar. Then drain the water. Remember that there should be no water accumulation in the barrel to prevent the formula from changing and even rusting of the pages and other links.

Synchronous gravel sealer fog sealer is a method of road maintenance. Some roads have network cracks, cracks and holes after a few years of use. The effective method is fog seal technology. The cost is very low. After the fog seal, due to the large fluidity of the material, it can penetrate into the aggregate and flow into the cracks to “transfuse” the road surface, restore the asphalt adhesion of the road surface, fill small cracks and gaps, prevent water from penetrating the road surface, and keep the road surface performance for 2 to 3 years, delaying the high maintenance cost and improving the economic benefits.

Asphalt emulsifier is an emulsifier that belongs to the category of surfactants and is a raw material for the production of emulsified asphalt.
Emulsifiers are divided into: synthetic emulsifiers, natural emulsifiers, inorganic powder emulsifiers, etc. Currently, synthetic emulsifiers are widely used. Asphalt emulsifier is a type of chemical organically synthesized surfactant.

Asphalt spreader is used to spread the penetration oil, waterproof layer and bonding layer of the bottom layer of asphalt pavement of high-grade highway. It can also be used for the construction of county and township highway oil roads with layered paving technology. It consists of a car chassis, an asphalt tank, an asphalt pumping and spraying system, a thermal oil heating system, a hydraulic system, a combustion system, a control system, a pneumatic system, and an operating platform.
Knowing how to properly operate and maintain the asphalt spreader can not only extend the service life of the equipment, but also enable the construction project to proceed smoothly. So what problems should the asphalt spreader pay attention to when working? The technicians of Gaoyuan Road Construction Machinery Equipment Co., Ltd. give you tips:
1). Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreader, check the four thermal oil valves and the pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Test the asphalt pump and circulate for 5 minutes. If the pump head shell is hot, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not turn or make noise. In this case, the valve needs to be opened to continue heating the asphalt pump until it can operate normally. During the working process, the asphalt liquid must be kept at a working temperature of 160~180℃, and it cannot be filled too full (pay attention to the liquid level pointer during the injection of asphalt liquid, and check the tank mouth at any time). After the asphalt liquid is injected, the filling port must be closed tightly to prevent the asphalt liquid from overflowing during transportation.
2). During use, asphalt may not be pumped in. At this time, it is necessary to check whether the interface of the asphalt suction pipe is leaking. When the asphalt pump and pipeline are blocked by solidified asphalt, a blowtorch can be used for baking, and the pump must not be forced to turn. When baking, care should be taken to avoid directly baking the ball valve and rubber parts.
3). When spraying asphalt, the car should be driven at a low speed. Do not step on the accelerator hard, otherwise it may cause damage to the clutch, asphalt pump and other components. If 6m wide asphalt is spread, pay attention to obstacles on both sides at any time to prevent collision with the spreading pipe. At the same time, the asphalt should be kept in a large circulation state until the spreading work is completed. After the work is completed every day, if there is any remaining asphalt, it must be returned to the asphalt pool, otherwise it will solidify in the tank and cannot work next time.
4). In addition, the emulsifier must also pay attention to daily maintenance:
1. The emulsifier and delivery pump and other motors, agitators, and valves should be maintained daily.
2. The emulsifier should be cleaned after work every day.
3. The speed regulating pump used to control the flow should be regularly tested for accuracy, and adjusted and maintained in time. The asphalt emulsifier should regularly check the matching clearance between its stator and rotor. When the minimum clearance specified by the machine cannot be reached, the stator and rotor should be replaced.
4. If the equipment is out of use for a long time, the liquid in the tank and pipeline should be emptied (the emulsifier aqueous solution should not be stored for a long time), the hole covers should be tightly closed, kept clean, and the running parts should be filled with lubricating oil. When it is used for the first time or when it is used again after a long period of inactivity, the rust in the tank should be removed, and the water filter should be cleaned regularly.
5. Regularly check whether the terminal in the electric control cabinet is loose, whether the wires are worn during shipment, and remove dust to avoid damage to the machine parts. The frequency converter is a precision instrument. Please refer to the instruction manual for specific use and maintenance.
6. There is a heat transfer oil coil in the emulsifier water solution heating stirring tank. When injecting cold water into the water tank, the heat transfer oil switch should be turned off first, and then the switch should be turned on to heat after adding the required amount of water. Pouring cold water directly into the high-temperature heat transfer oil pipeline can easily cause the weld to crack.

During the road construction process, asphalt spreaders also play an irreplaceable role. Let’s take a look at the main performance advantages of asphalt spreaders produced by Sinoroader and where their main contributions exist?
1. Manual/automatic control of spraying volume and working width. Each nozzle can be controlled individually, and the determinant nozzles can be freely combined to adjust the spraying width at will. Spreading control can be performed in the cab or the rear platform.
2. The automatic control system can measure the vehicle speed and automatically calculate the number of revolutions of the asphalt pump according to the input spreading volume, spraying width and asphalt type, and then automatically adjust the number of asphalt pumps through the system.
3. The vehicle-mounted rapid heating system (10-15℃/h) can improve the heating efficiency and reduce the construction auxiliary time and spreading temperature;
4. The flushing nozzle system can blow out the remaining asphalt in the nozzle through diesel and high-pressure air to prevent the asphalt from freezing in the nozzle and increase the service life of the nozzle.