Staff installs asphalt plant support rack details

FILLER STORAGE SILO

The asphalt mixing plant is constructed according to a certain process, which can not only ensure the construction quality, but also ensure that the asphalt mixing plant is not damaged. Although the construction details are critical, the key skills of the asphalt mixing plant construction must be mastered.
Before the construction of the asphalt mixing plant, the top surface of the asphalt mixing plant construction range should be removed, and the dry and flat site elevation should be kept to meet the design requirements. If the ground surface is too soft, the foundation should be reinforced to prevent the construction machinery from becoming unstable and to ensure that the pile frame is vertical.

1: The site should be located on higher ground and away from residential areas and densely populated areas.
Because part of the equipment of the mixing station is installed below the ground, in order to avoid continuous rainfall. The equipment will suffer disaster, and the changing aggregate moisture content will affect the concrete quality. Quality accidents are prone to occur. Therefore, during site construction, attention should be paid to the construction of drainage pipelines and sand and gravel quarries. With the rapid development of cities. With the continuous expansion of urban scale, environmental protection requirements will become more and more stringent. Urban roads prohibit gravel vehicles from passing, so concrete mixing plants should be built far away from urban areas.

In recent years, asphalt pavement has dominated highway surfaces. With the rapid development of our country’s national economy, highway traffic volume is increasing, axle loads are increasing rapidly, vehicle speeds are increasing, and there are more and more quality problems occurring on asphalt pavements. Some are damaged after repair, and some have a service life of up to Less than design age. This has put forward increasingly higher requirements for the quality of asphalt pavement, and an important factor affecting the performance of asphalt surface layers is the gradation composition of the mixture. This article discusses the mix design of asphalt mixture.

Mechanism to avoid asphalt damage in asphalt mixing plant
1. Asphalt operators should undergo physical examination. Anyone suffering from conjunctivitis, skin disease or allergic reaction to asphalt should not engage in asphalt work.
2. Asphalt operators must apply protective ointment on exposed parts of their skin, and a first aid kit should be provided on the construction site.
3. The factory uniforms and protective equipment of asphalt operators are stored in a centralized manner and are prohibited from being worn home or entering collective dormitories.
4. The transfer of lumpy asphalt should usually be carried out at night and on cloudy days, especially during hot seasons. Small machinery should be used for loading and unloading, and it should not be lifted and transported directly by hand.

In the construction industry, the installation and application of asphalt mixing plants can often be seen. This kind of equipment can complete the processing process of limestone and other powder products. The equipment has a reasonable structure and high working efficiency. It can save more costs for manufacturers during the production of asphalt raw materials. Therefore, the construction and other industries now attach great importance to the application of this equipment. During the production and processing of the equipment, the staff also need to pay attention to several operating skills to ensure that the equipment can operate stably and provide more benefits for production work.

Asphalt mixing equipment is equipment used to produce asphalt concrete in large quantities. Because this equipment is affected by various factors during the production process, some problems will inevitably occur after a period of use. Sinoroader Group The editor of the asphalt mixing equipment company of China Machinery Co., Ltd. will introduce to you the methods of rescuing damaged parts in asphalt mixing equipment.
Asphalt mixing equipment encounters different problems, and the solutions are also different. For example, one of the common problems of asphalt mixing equipment is that parts are worn out and damaged. The solution that needs to be done at this time is to start from the production of parts. Just start improving.

Asphalt mixing plant is a complete set of equipment composed of many systems. It is widely used in the current society. Its components include batching system, drying system, combustion system, hot material lifting, weighing and mixing system and control system.
In the process of asphalt mixing, heating is an indispensable link, because there must be a system for heating in the asphalt mixing station, but the system generally fails for various reasons. So how should the heating system of the asphalt mixing station be improved? This article will briefly explain this issue.
Generally speaking, when the asphalt mixing station is running under low temperature conditions, the asphalt circulation pump and spray pump cannot operate normally, which will cause the asphalt in the asphalt scale to solidify, and then the asphalt mixing station cannot be produced. Therefore, the asphalt mixing station needs a heating system during operation.

With the rapid development of highway construction and the increase in demand for asphalt, barreled bitumen has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported bitumen used in high-grade highways is in barrel form, which requires an bitumen melter equipment with fast melting speed, clean debarreling, and prevention of asphalt aging.
The upper part of the debarreler of the bitumen melter equipment is hotter, and each barrel is directly heated by the heat transfer oil coil. The barrel wall directly bears the heat radiation of the heating coil. The asphalt is cleanly and sensitively debarreled, and there will be no waste of asphalt hanging barrels. According to the principle of layered heating, four-layer heating technology is adopted, with single inlet and single outlet of heat transfer oil, and high thermal efficiency of heating; at the same time, the waste heat of combustion exhaust gas is used for secondary heating, and power is effectively used; the debarreler body is insulated with high-quality rock wool material. It is suitable for various types of imported and domestic barrels, and the deformation of asphalt barrels will not affect production.

Natural gas is a colorless, odorless, flammable and explosive gas, the main component of which is methane, which accounts for about 98% of natural gas. The density of natural gas is lower than that of air and it is difficult to liquefy. Natural gas is not only a clean green energy for civil, commercial and industrial use, but also a raw gas for chemical industry. The theoretical ignition value of natural gas is 540 degrees, the combustion temperature is 1970 degrees, the calorific value is 40MJ/m3, and the explosion limit is 5%-15%. CNG refers to natural gas that has been compressed to 20-25MP and stored in high-pressure gas tank trucks, and then transported to various gas transmission points to supply gas to residential users, commercial users and industrial users. In order to ensure the normal operation and safety of the asphalt mixing station and our pressure regulating station, our company has specially formulated the following safety protection measures.

At present, the production efficiency of asphalt mixing plants in my country’s asphalt construction is far lower than the theoretical efficiency at the time of design. The low efficiency of organic waste gas treatment will not only delay the construction process and cause a waste of resources, but also the quality of the construction will not be very good. guarantee. In the construction of asphalt pavement, the main reasons for the low production efficiency of the asphalt plant are insufficient supply of mixture, resulting in loss of continuity of construction, improper equipment parameter settings, excessive overflow and other problems. Effective measures must be taken to deal with these problems, and ultimately improve production efficiency and ensure construction quality.

When using an asphalt mixing plant, first of all, it needs to have good stability. If it does not have good stability, then the asphalt mixing plant will not be able to meet the requirements of the project in terms of requirements or mass production. For road construction, the measurement requirements of asphalt concrete are relatively strict and precise. Only qualified asphalt concrete can make the quality of road construction meet the actual requirements. Therefore, the stability of the asphalt mixing plant is very important.
Secondly, the requirements for the asphalt mixing plant when in use are that the equipment should be as simple as possible on the basis of having all the required functions, and the overall operation should be reduced as much as possible. This can save a lot of manpower input during operation and save corresponding costs. Although it is simple, it does not mean that the technological content of the asphalt mixing plant needs to be reduced.
The above are the requirements that the asphalt mixing plant needs to meet when in use, because if each equipment wants its working effect to achieve the expected appearance, the equipment itself needs to have corresponding conditions. It must be a qualified and convenient equipment to ensure the efficiency and quality of the work.

The renovation of the combustion-supporting system of the asphalt mixing plant and the use of DC frequency conversion CNC machining technology are all renovations of the original system. In addition to the above renovation plans, with the existing equipment and personnel, what other measures can be taken in the application to reduce the operating costs of concrete mixing plants?
At present, China has no mandatory national industry standards for heavy residual oil, and the quality of fuel oil varies greatly. Even from the same dealer, the quality difference between batches is very large, and it contains more residues. Therefore, bridge inspection equipment should be installed on the construction site, and professional personnel should inspect various performance parameters of gasoline and diesel to strictly control quality.
When the burner is working, if the flame of the combustion aid is red and the smoke from the ash removal chimney is black, this is the manifestation of poor atomization of gasoline and diesel and insufficient combustion aid. At this time, the following measures should be taken to deal with it: properly adjust the distance between the nozzle and the vortex plate, generally push it inward to a suitable distance, the purpose is to prevent the atomized oil cone sprayed from the nozzle from spraying into the vortex plate; effectively adjust the ratio of gasoline and diesel to gas, so that the gasoline and diesel increase the mass conversion law slowly, or the gas increase the mass conversion law quickly; promptly remove the carbon deposits and coke around the nozzle to prevent the flame from deflecting; heavy residual oil contains more residues, which can easily cause serious damage to the high-pressure oil pump and increase the working pressure, affecting the actual effect of atomization and the shape of the flame, so the high-pressure oil pump must be repaired or replaced in time; install metal filter devices in front of the first and second high-pressure oil pumps, and clean them frequently to prevent the residues in the gasoline and diesel from blocking the nozzle.
The operators should be trained in professional skills on a regular basis to strengthen their job responsibilities and moral education, so that they can establish their respective job responsibilities, understand the importance of their positions, understand the content of their work, and improve their professional level. Skilled operators can properly control the temperature of the asphalt mixing plant mixture to avoid gasoline and diesel waste.
In order to improve the combustion-supporting effect and effectively reduce the operating costs of asphalt mixing stations, Sinoroader Group kindly reminds that the following issues should be noted when using the burner in the asphalt mixing station: To improve the maintenance of the burner, the burner nozzle should be cleaned of charred materials and carbon deposits on the ignition electrode regularly. The nozzle can be disassembled according to the atomization status; the air-oil ratio of the burner is generally not adjusted, and the fuel pump pressure can be adjusted according to the smoke status and the temperature of the asphalt mixture; the sulfur dioxide generated by the combustion of light fuel oil has a strong corrosion to the bag, so the bag should be maintained regularly and the air pressure changes in the bag should be paid close attention to; water deashing will produce more foam, causing the sand settling tank to flow out, so the sand settling tank should be cleaned in time, and a watering design should be carried out to settle the foam; when the steam pressure decreases or the gear oil pump noise increases, the gear oil pump must be replaced.
When the burner is started, the fuel oil circulation system should be completed through the valve, and then the burner control box should be opened to start the burner. If the electronic ignition of the fuel oil fails, you can change the inlet tee and use the diesel engine for ignition. After the ignition is successful for 2 minutes, you can convert it into fuel oil. In this way, even the light fuel oil of lower quality can ensure combustion.

Asphalt concrete mixing equipment generally uses conveyor belt conveyors to transport cold materials. Its main advantages are large conveying capacity, continuous operation, simple equipment structure and automatic control. However, belt deviation is a common fault, which directly affects the drying operation of the drying drum and also affects the production efficiency of the mixing equipment. Therefore, it is very important for the asphalt mixing station to solve the belt deviation problem at the operation site of the asphalt concrete mixing equipment.

After use, asphalt mixing equipment needs to be disassembled, cleaned, and maintained before it can be saved for next use. Not only is the disassembly process of the equipment important, but the previous preparation work also has a greater impact, so it cannot be neglected. Please pay attention to the detailed introduction below for specific content.

For road construction machinery, the following is mainly about the asphalt mixer in road construction machinery equipment. Because it is the key product of Wuxi road construction machinery manufacturers, it is necessary to carry out comprehensive training and mastery, so as to ensure meticulousness and practicality, and not ignore any knowledge points.
1. In road construction machinery, is there any difference between asphalt mixing equipment and asphalt concrete mixing equipment?
The answer given by Sinoroader Group manufacturer to this question is no, that is, there is no difference between asphalt mixing equipment and asphalt concrete mixing equipment. They refer to the same type of equipment, but they are different in name. It can be said that they are two names for the same type of equipment, and there is no difference in essence.
2. During the operation of the asphalt mixer, there is a sound in the mixing pot. What’s the matter?
In the view of Sinoroader Group, there are two answers to this question. One is that the mixer arm on the asphalt mixer is not good or damaged. The second is that the wear-resistant lining in the mixer is damaged, which leads to this problem.
3. What are the dust removal devices in the asphalt mixing equipment?
In the asphalt mixing equipment, for its dust removal device, Sinoroader Group believes that the key is to use the dry ash removal method, because it can facilitate the collection of raw materials. In terms of its dust removal equipment type, there are filter dust removal equipment, centrifugal fan dust removal equipment and force dust removal equipment, etc., which can all be used well.
For the asphalt mixer and asphalt mixing equipment in road construction machinery, I believe that through the practical discussion of the above relevant content, everyone can master it well and master it, so that in practice, they can have new gains and benefit a lot from it.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixer plant also needs to be powered on for trial operation before it is officially put into work.
At the beginning of the test run, first run a single motor, and at the same time check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

The application of asphalt mixing plants also involves selection issues. In order to give full play to the performance of the equipment, the model of the machine is mainly determined according to the actual situation of the construction site. It sounds relatively simple, but some details still need to be emphasized.
The so-called specific conditions of the construction site first include the size of the site; secondly, the properties, specifications and working dimensions of the enterprise’s supporting equipment. It is necessary to try to do a good job in all aspects to help improve production efficiency and ensure product quality. In the case of intensive network management, the network management function of the asphalt mixing plant must also be taken into account to avoid difficulties in future upgrades.

BITUMEN SUPPLY SYSTEM

1. Causes of overflow
The main causes of spillage are:
1) Mixing materials in cold silo. Cold material warehouses generally have 5 or 4 warehouses. Each warehouse is required to contain pellets of a certain specification. If cold materials of different specifications are mixed or mistakenly loaded during the loading process, it will cause certain occurrences in a certain period of time. The shortage of pellets of one specification and the overflow of pellets of another specification can easily destroy the supply balance between hot and cold silos.

Electrical control system

Asphalt flue gas treatment methods, their principles and characteristics, and an asphalt flue gas environmental protection treatment plan based on the actual asphalt flue gas problems faced by the unit.

1. Basic situation
My unit’s mixing plant is equipped with a 4000-type asphalt mixing plant. During daily production of the asphalt mixing plant, a large amount of asphalt smoke will be emitted from the mixing pot discharge port. This smoke not only has an unpleasant smell, but also contains A large number of compounds that are harmful to the human body, such as benzopyrene, benzanthracene, carbazole and other polycyclic aromatic hydrocarbons, mostly have carcinogenic risks. Smoke overflow will cause pollution to the surrounding atmospheric environment and affect the personal health of workers. Although the overflow port of the mixing station is equipped with a dust retaining wall, the fine dust is seriously raised, and the cold material belt conveyor is dusty. In order to protect the environment, reduce pollution, and reduce cost investment, based on full research and absorption of technology in the same industry, and combined with the actual situation of asphalt mixing, we are planning to install asphalt mixing bag dust collectors to the flue at the discharge port of the mixing pot to control asphalt fumes. Gas is processed. The dust removal efficiency of the bag dust collector can reach 97%~99%, and the dust-containing gas can be purified to a level of 50mg/Nm3.

Emulsion bitumen equipment has stable product quality, closed material transmission, high degree of automation and civilized production, and is easy to standardize management. The double-mill configuration can be used to produce modified emulsified asphalt.
At present, emulsified asphalt equipment is widely used in new technologies and processes for preventive maintenance, such as fog seal, slurry seal, micro-surfacing, cold regeneration, crushed stone seal, cold mix and cold patch materials.
Emulsion bitumen equipment is an emulsion at room temperature formed by dispersing asphalt into the water phase. It is a new material for the use of elements. Compared with traditional hot asphalt, it saves more than 50% of energy and 10%-20% of asphalt, and has little pollution. The biggest feature of emulsified asphalt is that it can be stored at room temperature. It does not need to be heated during spraying and mixing, nor does it need to heat the stone. Therefore, it greatly simplifies the construction, avoids burns and scalds caused by hot asphalt, and avoids the fumigation of asphalt steam when paving high-temperature mixtures. It is very popular among road maintenance workers.

Due to its complexity and importance, asphalt mixing plants are more critical in road construction. Modern asphalt mixing stations have five key systems. Do you know what they are?
1. Mixing system of asphalt mixing plant
Mixing equipment is one of the key systems, why? Usually, the productivity of the mixing equipment has a great impact on the next step of construction efficiency. Most asphalt mixing plants use twin-shaft forced mixing. Since the drying drum and burner of the mixing equipment have strong overload capabilities, and in most cases, the moisture content of the mineral materials is less than 5%, this improves the productivity of the mixing equipment. provide conditions. The mixing blades of the mixer have an adjustable assembly angle and are driven by dual mixing shafts and dual motors.

Sinoroader secondary bag filter systems are guaranteed to deliver dust emission levels of less than 20 mg/m³ and enables asphalt plants to be sited in the most environmentally sensitive locations.

Oscillating screen. It can screen the heated aggregate according to the design. It requires fully enclosed, double oscillating motor replacement (replacing one substance for another (mostly the strong one takes the place of the weak)) eccentric shaft oscillation, each The layer screen is easy to install quickly. The service life of the drying roller and the power part is not less than 6000h. The roller can fully use heat, the material curtain flows evenly, and the inclination is required to be adjustable.

When inspecting the asphalt mixing plant, it was found that the asphalt in the pipeline solidified because the temperature of the asphalt transportation pipeline did not meet the requirements. Analysis believes that the reasons for this result are that the high-level oil tank of the heat transfer oil is too low, resulting in poor circulation of the heat transfer oil; the second is that the inner tube of the double-layer pipe is eccentric; the third is that the heat transfer oil pipeline is too long; and the fourth is that the heat transfer oil pipeline is not insulated measure.

In recent years, asphalt concrete, as a new green building material, is gradually being valued by people because of its excellent performance in saving resources, being environmentally friendly, ensuring the quality of construction projects, and achieving sustainable utilization of resources. The development of asphalt concrete fully embodies my country’s policies to achieve energy conservation and emission reduction, and is also an important measure to promote the development of circular economy.

Any kind of mechanical equipment must go through precise design, testing and other processes before it can be manufactured, and the same is true for asphalt mixing stations. According to the survey, the following stages are necessary for any asphalt mixing plant.
First of all, the main technical parameters of the product to be designed must be determined according to market needs, so construction market research, data analysis and other links are indispensable. Secondly, the ideal working principle and the plan to realize this principle will be determined through innovative conception and optimization screening. , a schematic diagram of the overall design scheme should also be given.