Technical features of synchronous sealing car fiber sealing equipment

Asphalt used to pave roads. It can be obtained by regular vacuum distillation of crude oil with appropriate properties, and can also be obtained by shallow oxidation of vacuum residue or propane deasphalting process. It can also be prepared by mixing asphalt of different duction and injection degree

Each F1 track must be paved with three layers of asphalt, middle and lower, of which the lowest layer is 10 cm coarse asphalt concrete bearing layer, its flatness is less than 8 mm; In the middle is a 4 cm medium grained asphalt concrete bond layer, its flatness is less than 5 mm; The top layer uses 4 cm modified asphalt mixture as the surface wear layer, and the flatness is less than 2 mm.

The paved F1 track cannot have more than 3 points per kilometer of flatness detection, which is much higher than the highway.

Classification analysis of emulsion bitumen equipment is used to heat-melt bitumen. According to the actual cutting effect of mechanical equipment, it is loosened into a solution with demulsifier in the form of tiny droplets to form oil-in-water asphalt. Industrial equipment for lotions. Emulsion bitumen equipment can be divided into three types: portable, transportable and mobile according to the equipment, layout and maneuverability of the equipment.

1. When operating an asphalt spreading truck, first check whether the machinery, spreading devices, protective and fire prevention equipment are complete and effective.
2. It is strictly prohibited to use non-specified fuel as the fuel for the heating system. The fuel is not allowed to overflow outside the tank. Generally, the oil level should be 20-30cm lower than the upper end of the overflow pipe.

Preventive pavement maintenance is a periodic mandatory maintenance measure, which is taken to restore the pavement surface service function when the pavement structure strength is sufficient and only the surface function is attenuated. New preventive maintenance technologies such as super-viscous fiber-added low-noise micro-surfacing and synchronous gravel seal have been widely used on the main lines of national highways, and the construction effect has been widely praised by customers.
Super-viscous fiber-added low-noise micro-surfacing starts with the gradation of micro-surfacing and the main material modified emulsified asphalt. By reducing the structural depth of the micro-surfacing and changing the distribution state of the coarse and fine materials on the surface of the micro-surfacing, the driving noise is reduced, while ensuring its anti-skid performance, effectively improving its adhesion, waterproofness, durability and crack resistance, and can solve the defects of easy detachment, excessive noise and reflective cracks of ordinary micro-surfacing.

Improve the reliability of SBS bitumen emulsion plants: Once you have an established maintenance, it will help to identify problems. This will allow the maintenance plan and time to be carried out at your convenience. Regular maintenance will increase the normal operation time of SBS bitumen emulsification equipment, and it can be used when necessary. Low cost of operation: Imagine an SBS bitumen emulsification plant breaks down during a project. With a protective maintenance plan, such things happen less often because you have taken good care of the SBS bitumen emulsification plant.
If the SBS bitumen emulsification plant wants to maintain normal operation, then in the production process. All stages need to be maintained normal, among which the normality of the circuit system is an important aspect to ensure its smooth operation. Imagine that if there is a problem with the circuit during the on-site operation, it may affect the development of the entire project.
For users, of course, they don’t expect this to happen, so if the SBS bitumen emulsification plant is in the work of using the SBS bitumen emulsification equipment, if there is a circuit problem, it is necessary to take appropriate measures to solve it in time. The following article will give a detailed description of this problem, and the following SBS bitumen emulsification plant can be of benefit to everyone.

When performing bitumen melting, specialized equipment is required. These equipment usually include bitumen melting furnaces, asphalt mixers, asphalt conveying equipment, etc. Among them, the bitumen melting furnace is one of the most advanced equipments, which can heat solid bitumen to liquid state. In addition, asphalt mixers can mix liquid asphalt with stone to make asphalt concrete. , Asphalt conveying equipment can transport asphalt concrete to the construction site. The selection and use of these equipment are of great significance to ensure the quality of bitumen melting and construction efficiency.

How to reduce energy consumption of emulsified asphalt machinery is a concern of many users and many manufacturers. Therefore, today, Sinosun Company, as a manufacturer of emulsified asphalt equipment, would like to take this opportunity to share with you the method of reducing energy consumption of emulsified asphalt machinery.
Since emulsified asphalt appears as a finished product in emulsified asphalt machinery, and the outlet temperature of ordinary emulsified asphalt is about 85℃, and the outlet temperature of emulsified modified asphalt is above 95℃, there is a lot of latent heat in emulsified asphalt, but the emulsified asphalt equipment does not make good use of them, but directly enters the finished product tank, allowing heat to be lost at will, resulting in energy waste.

In addition to being used according to regulations, modified bitumen equipment should also be maintained regularly in order to effectively extend the service life of modified bitumen equipment. The delivery pump of modified bitumen equipment, as well as its motor and reducer, need to be maintained in accordance with the specifications of the instructions. If the modified bitumen equipment is parked for a long time, the liquid in the tank and pipeline needs to be drained, and each moving component also needs to be filled with grease. The dust in the control box of the modified bitumen equipment needs to be cleaned once every six months. A dust blower can be used to remove dust to prevent dust from entering the machine and damaging parts. The micro powder machine needs to add unsalted butter once for every 100 tons of emulsified bitumen produced.

The fine surface is made of stone with a single particle size, which has high wear resistance and anti-slip properties. The construction of the fine surface adopts mechanized construction, which requires less manual labor and has the characteristics of fast construction speed, anti-skid and noise reduction.
The special bonding material for fine surfaces produced by Sinoroader Group has the characteristics of good bonding performance and good durability. The specific construction process is roughly as follows:

Synchronous chip seal is a process technology for treating cracks in asphalt pavement, and it is currently a highway construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical characteristics are? If you don’t know, follow the editor of Sinoroader company to have a look.

Asphalt melting equipment is an important road construction tool used to heat asphalt to the appropriate temperature for construction. It can provide reliable solutions and make road construction more convenient. The working principle of this equipment is to heat the asphalt to the appropriate temperature through a heater, and then transport the hot asphalt to the construction site through a conveying system.

Precautions for checking emulsified asphalt equipment
Sinoroader emulsified asphalt pavement engineering common equipment, now has gradually been widely used.
We all know that before any equipment is used, the equipment should be preliminarily inspected to check whether the installation is normal, and then put into use. The use of modified asphalt modified asphalt production equipment can also extend the peak season. The modified asphalt and stone water machine can be mixed with wet stone to form a continuous film under the surface conditions of low-temperature asphalt and stone. The viscosity of the asphalt is low and the viscosity of the emulsified asphalt is low. Wet film below 10 degrees.

For each equipment used, certain safety knowledge must be followed. For the use of emulsified asphalt equipment, detailed instructions are given:
1. Placement: The emulsified asphalt equipment should be placed on a flat place, the front axle should be fixed to the sleepers, and the tires should be dangling. The machine should not be fiddled with at will to affect normal operation.
2. Regularly check whether the mixer blades are deformed and the screws are loose.
3. Check whether the running direction of the mixing drum is consistent with the direction of the arrow. Please replace the positive and negative poles of the terminal.
4. Before turning on the power, check the no-load test run, check for air leakage, and check the idling speed of the mixing barrel. The normal speed is about 3 times faster than the empty car. If not, stop the inspection.
5. If the asphalt material is stopped for one hour after mixing, clean the mixing barrel, pour in clean water, and clean the mortar. Then drain the water. Remember that there should be no water in the barrel to prevent the formula from changing, so that the page and other links will rust. Sinoroader will provide you with more safe emulsified asphalt knowledge, please continue to browse.

During the use of emulsified bitumen equipments, if maintenance is not paid attention to, the cycle will be short, and problems will often occur during use. Only by doing a good job of maintenance can the operation efficiency of the equipment be improved. For example, during maintenance, the following points must be grasped.
It is necessary to regularly check the wear condition of the internal structural components of the mechanical equipment, such as the core feed pipe, the rough jaw plate on the impeller, the cone cap, the wear level of the jaw plate, the rain shield on the circle, and the wear condition. If the wear is more serious, it is necessary to replace or repair it in time. When replacing, it is also necessary to pay attention to the model and specifications, and replace it according to the original components as a reference.

The requirements for SBS asphalt emulsification equipment are very high. The micro powder machine must have a sufficiently large driving force and can bear the condensation type. Because the temperature requirements of the emulsion SBS asphalt process are relatively high, the emulsified asphalt should be passed through a heat exchanger before feeding to reduce the emulsified asphalt temperature to below 90°C to prevent the emulsified asphalt from breaking due to excessive temperature.
The application scope of SBS modified emulsified asphalt is very wide. According to the nature of the construction, it can be used in new construction, renovation, and reconstruction projects; according to the nature of the project, it can be used in overhaul, equipment overhaul, and maintenance projects. Among them, the actual application projects include micro-surfacing, cold regeneration, cold mixing and cold paving, adhesive layer, permeable oil, slurry seal, gravel permeable layer, fog permeable layer, road moisture-proofing, SBS membrane, ground seam filling, and all other projects that can use emulsified asphalt.

Maintenance points of asphalt spreading trucks in different working hours
per month (or every 200 hours worked)；
​Per year (or every 500 hours worked)；
Every two years (or every 1,000 hours worked)；

What is an bitumen colloid mill used for? Everyone knows about colloid mill, but what about bitumen colloid mill?
Bitumen colloid mill is a high-tech multifunctional crushing and grinding equipment. The motor drives the rotating teeth and fixed teeth to rotate at high speed, generating a sharp speed gradient, which causes the boring to be strongly sheared, rubbed and turbulent, and finally achieves emulsification and dispersion. and homogenizing effect equipment.

Friends who are ready to get started have a surprise today. The editor will give you a brief introduction on how to produce emulsified asphalt.

The asphalt spreading truck is an intelligent high-tech product that specializes in spreading emulsified asphalt, diluted asphalt, hot asphalt, heavy traffic asphalt and modified asphalt. It is used in highway construction and highway maintenance projects, and can be used for the construction of upper and lower seals, permeable layers, waterproof layers, bonding layers, asphalt surface treatment, asphalt penetration pavements, fog seals and other projects of different grades of highway pavements. , can also be used for the transportation of liquid asphalt or other heavy oil. So what are the advantages of Qiangguomeng’s asphalt spreader trucks?

The container-type emulsified bitumen equipment hot-melts the base cold-mix colored bitumen and disperses it through the equipment into small cold-mix colored bitumen particles in an aqueous solution containing emulsifier to form a liquid cold-mix colored bitumen material.

Modified asphalt equipment is a widely used asphalt equipment. Now its ultra-high performance has been widely praised by users. However, we must first use the modified asphalt equipment safely to fully demonstrate its performance. So how much do you know about the safe use and operation of modified asphalt equipment? Today, Sinoroader will explain it in detail:
1. Placement: The modified asphalt equipment should be placed on a flat place, and the front axle wheel should be fixed with sleepers and the tires should be dangling to ensure that the machine does not move around during operation.
2. Check regularly whether the mixer blades are deformed and whether the screws are loose.
3. Check whether the running direction of the mixing barrel is consistent with the arrow. If not, please replace the positive and negative poles of the wiring.
4. Before powering on, check for empty vehicle trial operation, check for leakage, and check the idling of the mixing barrel. The normal speed is about 3 times faster when the empty vehicle is full. If the speed is wrong, stop the car for verification.
5. If the asphalt material is stopped for one hour after mixing, clean the mixing barrel, pour in clean water, and clean the mortar. Then drain the water, remember that there must be no water in the bucket to prevent the formula from changing, and even rust on the pages and other links. During use, everyone should pay attention to some small links to avoid unnecessary losses in their work.

The base layer of asphalt pavement is divided into semi-rigid and rigid. Since the base layer and the surface layer are materials of different properties, good bonding and continuity between the two are the key requirements for this type of pavement. In addition, when the asphalt surface layer seeps water, most of the water will be concentrated at the joint between the surface layer and the base layer, causing damage such as slurry, looseness, and potholes to the asphalt pavement. Therefore, adding a lower seal layer on top of a semi-rigid or rigid base layer will play a vital role in enhancing the strength, stability and waterproofing capabilities of the pavement structural layer. The more commonly used one is to use asphalt gravel synchronous sealing technology.
So let’s take a look at how the construction of the asphalt gravel synchronous sealing truck is carried out:

The viscosity of the drum bitumen decanter equipment decreases as the temperature increases during the production process. Its output viscosity is about twice as high as every 12°C increase. During production, the base bitumen decanter equipment must first be heated to a liquid state and then emulsified. In order to better integrate the emulsification ability of colloid milling, the viscosity of base bitumen decanter is generally controlled to be about 200 cst. The lower the temperature, the higher the viscosity, which increases the pressure on the bitumen decanter pump and colloid milling, making emulsification impossible: However, on the other hand, in order to prevent the bitumen decanter equipment from weaning when the moisture of the finished product evaporates, it is impossible to heat the base asphalt barrel removal temperature too high, and generally use a colloid grinding inlet and outlet system. The finished product temperature should be below 85°C.

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

The advantages of Sinoroader bitumen decanter equipment over similar domestic equipment are reflected in the following points:
1. The equipment produces 8-10t/hour, with an automatic telescopic sealed container structure. It uses an electric hoist to lift the asphalt barrel at the inlet guide tube. Start to control the hydraulic cart forward button, which will promote the barrel push (push and slide into the barrel). It is a 1300mm hydraulic cylinder with a 7.5-ton top thrust. The device has a beautiful appearance, reasonable layout, compactness, stable performance, and is suitable for production under various industrial and mining conditions.
2. Fast barrel removal: According to the principle of layered heating, it adopts four-layer thermal oil heating technology, a single inlet and outlet, and high thermal efficiency of heating; at the same time, it uses the waste heat of combustion gas for two heatings and efficient use of energy; the barrel body uses high-quality rock wool insulation material.
3. Good environmental protection: closed structure, no pollution.
4. No barrel hanging: The upper part of the asphalt barrel is hot, and each is directly affected by the thermal oil heating pipe. The barrel wall directly receives the heat dissipation of the heating coil, and the barrel is clean and fast, which will not cause waste of asphalt barrel hanging.
5. Strong adaptability: Suitable for imported and domestic barrels, and the deformation of asphalt barrels will not affect production.
6. Good dehydration: Use a large-displacement asphalt pump for internal circulation, stirring, water vapor overflows, and is naturally discharged from the exhaust port. After dehydration, asphalt can be directly used to produce asphalt mixture or used as matrix asphalt.
7. Automatic slag removal: This set of equipment has an automatic slag removal function. The filter device sets the asphalt circulation pipeline through the filter, which can automatically remove the barreled asphalt slag.
8. Safe and reliable: The equipment adopts an automatic control system, an automatic ignition burner import, can automatically control the temperature according to the temperature, and is equipped with corresponding monitoring instruments.
9. Convenient relocation: The whole machine is assembled with large components, which is easy to move and quick to assemble.

Contemporary roads and pavements have undergone many changes: traffic volume and driving frequency have increased significantly, the axle load of logistics trucks has continued to increase, one-way driving in separate lanes has been widely implemented, and regulations have further improved the anti-flow resistance of the ground, that is, the work of modified asphalt equipment under high temperatures ability;

Synchronized gravel sealing is a process technology for treating cracks in asphalt pavement, and it is currently a road construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical features are? If you don’t know, just follow the editor of Sinoroader and take a look.

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.

For the relevant knowledge of modified asphalt equipment, we have more or less introduced it in the above articles. I believe that most users also have some simple understanding of it. Today we also mastered:
In order to meet the different requirements of customers, the configuration and process of the equipment produced by the manufacturers of modified asphalt equipment are diversified. There are fixed production types, mobile types, and imported main machines, but the imported main machines are expensive, so most customers configure domestic pipeline emulsifiers or colloid mills. In terms of the degree of automation, there are fully automatic production and semi-automatic production. Regardless of the form of production, each has its own advantages and disadvantages. What kind of process and configuration is used depends on the annual production volume and the customer’s requirements for equipment, product performance requirements and other factors. I hope that these introductions can help users choose to a certain extent.