The HMA-B series asphalt mixing plant can produce reliable quality asphalt

The drying and heating system of the asphalt mixing plant can be regarded as an important part of the whole, so in actual work, it treats the material in a countercurrent heating manner, thereby achieving full dehydration of the cold aggregate, and heating it to a certain temperature, thereby providing the necessary conditions for the normal and continuous operation of the asphalt mixing plant.
During the entire heating process of the asphalt mixing plant, the main purpose is to make the performance of the mixture more in line with the requirements of use, and to make the finished material have good paving performance. Under normal circumstances, the heating temperature of the aggregate is about 160℃-180℃.

Asphalt mixing station is one of the most important equipment in processing operations, so how to build a website has become the focus of people’s attention. The editor has compiled some key points, hoping to be helpful to everyone.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixer plant also needs to be powered on for trial operation before it is officially put into work.
At the beginning of the test run, first run a single motor, and at the same time check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

When we operate the asphalt mixing station, we should heat the equipment half an hour in advance, and the clear tank should be heated for at least two hours; and manually operate each part of the equipment to ensure that it is in good operation. status; it is also necessary to conduct relevant inspections on the valves and manually collect and return oil to ensure that the equipment can operate normally.
Several requirements for safe operation of asphalt mixing plants:

Oscillating screen. It can screen the heated aggregate according to the design. It requires fully enclosed, double oscillating motor replacement (replacing one substance for another (mostly the strong one takes the place of the weak)) eccentric shaft oscillation, each The layer screen is easy to install quickly. The service life of the drying roller and the power part is not less than 6000h. The roller can fully use heat, the material curtain flows evenly, and the inclination is required to be adjustable.

Asphalt mixing plant is a complete set of equipment composed of many systems. It is widely used in the current society. Its components include batching system, drying system, combustion system, hot material lifting, weighing and mixing system and control system.
In the process of asphalt mixing, heating is an indispensable link, because there must be a system for heating in the asphalt mixing station, but the system generally fails for various reasons. So how should the heating system of the asphalt mixing station be improved? This article will briefly explain this issue.
Generally speaking, when the asphalt mixing station is running under low temperature conditions, the asphalt circulation pump and spray pump cannot operate normally, which will cause the asphalt in the asphalt scale to solidify, and then the asphalt mixing station cannot be produced. Therefore, the asphalt mixing station needs a heating system during operation.

The asphalt mixing plant is constructed according to a certain process, which can not only ensure the construction quality, but also ensure that the asphalt mixing plant is not damaged. Although the construction details are critical, the key skills of the asphalt mixing plant construction must be mastered.
Before the construction of the asphalt mixing plant, the top surface of the asphalt mixing plant construction range should be removed, and the dry and flat site elevation should be kept to meet the design requirements. If the ground surface is too soft, the foundation should be reinforced to prevent the construction machinery from becoming unstable and to ensure that the pile frame is vertical.

Asphalt mixing equipment is a large-scale equipment, so you must pay attention to safety when using it to avoid accidents. But to put it simply, if you want to truly use it safely, you must master some basic common sense. The following main things must be kept in mind.

We know that the first priority in production is to ensure safety. In the process of operating equipment, staff must always pay attention to using the correct operating methods. Regarding the asphalt mixing plant, it is used to produce asphalt mixtures, modified asphalt mixtures, and colored asphalt mixtures to meet the needs of highways, graded highways, municipal roads, airports, etc.

As an important production equipment in construction, asphalt mixing plant has high production investment. Therefore, production is very important during use, but daily maintenance is also very important. In addition to regular maintenance, routine maintenance is also essential. The editor of Asphalt Mixing Plant shares some key points of daily maintenance and scheduled maintenance;

Determining the material is a necessary stage in the design process of asphalt mixing equipment, and it is also one of the most critical links, because the material will be directly related to the use effect and service life of the entire equipment. Generally, when we determine the machine material, we usually base it on the characteristics of the working medium, and the same is certainly true for asphalt mixing equipment.

For road construction machinery, the following is mainly about the asphalt mixer in road construction machinery equipment. Because it is the key product of Wuxi road construction machinery manufacturers, it is necessary to carry out comprehensive training and mastery, so as to ensure meticulousness and practicality, and not ignore any knowledge points.
1. In road construction machinery, is there any difference between asphalt mixing equipment and asphalt concrete mixing equipment?
The answer given by Sinoroader Group manufacturer to this question is no, that is, there is no difference between asphalt mixing equipment and asphalt concrete mixing equipment. They refer to the same type of equipment, but they are different in name. It can be said that they are two names for the same type of equipment, and there is no difference in essence.
2. During the operation of the asphalt mixer, there is a sound in the mixing pot. What’s the matter?
In the view of Sinoroader Group, there are two answers to this question. One is that the mixer arm on the asphalt mixer is not good or damaged. The second is that the wear-resistant lining in the mixer is damaged, which leads to this problem.
3. What are the dust removal devices in the asphalt mixing equipment?
In the asphalt mixing equipment, for its dust removal device, Sinoroader Group believes that the key is to use the dry ash removal method, because it can facilitate the collection of raw materials. In terms of its dust removal equipment type, there are filter dust removal equipment, centrifugal fan dust removal equipment and force dust removal equipment, etc., which can all be used well.
For the asphalt mixer and asphalt mixing equipment in road construction machinery, I believe that through the practical discussion of the above relevant content, everyone can master it well and master it, so that in practice, they can have new gains and benefit a lot from it.

At present, most asphalt mixing plants have different degrees of energy loss in use, and these losses have brought us serious waste. How to reduce energy consumption in these aspects and achieve efficient production?
First of all, we must first summarize which aspects have energy loss, and then we can find reasonable solutions based on these problems. Through research, it is found that there are four problems in the use of asphalt mixing plants and the production of asphalt mixtures. The content and measures are as follows:
The first aspect is the management of the pile. We can reduce the energy consumption of the asphalt mixing plant through 3 specific methods: 1. Appropriately reduce the stacking height of the pile; 2. Build an inclined pile site with a good drainage structure; 3. Build a waterproof canopy.

Road construction machinery is a large range, so let’s talk about one of it, which is the asphalt mixing plant. It is mainly used to produce asphalt, so it is very important among road construction machinery and equipment. An important part, if the quality of the finished product is not good, it will greatly affect the quality of the road. Therefore, below, the editor will use the form of question and answer to guide you to continue learning.

Certain failures cannot be avoided during the use of the asphalt mixing plant. For example, a malfunction of the cold material feeding device may cause the asphalt mixing plant to shut down. This may be due to a malfunction in the asphalt mixing plant or due to gravel or foreign matter being trapped under the cold material belt. If it is stuck, if it is a circuit failure, first check whether the motor control inverter of the asphalt mixing station is faulty and whether the line is connected or open.

The drive unit is one of the important components of the asphalt mixing plant, so whether it can be reliably operated must be highly valued to avoid adverse effects on the entire asphalt mixing plant. To ensure that the drive unit in the asphalt mixing plant is indeed complete and reliable, the following maintenance measures are essential.
The first thing to pay attention to is the universal rotating part of the drive unit of the asphalt mixing plant. This part has always been a fault-prone part. In order to reduce the occurrence of faults, grease should be added on time, and the wear should be checked frequently, and repaired and replaced in time. Users should also prepare the universal shaft assembly to avoid affecting the working process of the entire asphalt mixer.

Main uses of asphalt mixing plant
Asphalt mixing plant, also called asphalt concrete mixing plant, can produce asphalt mixture, modified asphalt mixture, and colorful asphalt mixture, fully meeting the needs of constructing expressways, graded highways, municipal roads, airports, ports, etc.
The overall composition of asphalt mixing plant
Asphalt mixing equipment mainly consists of batching system, drying system, incineration system, hot material improvement, vibrating screen, hot material storage bin, weighing mixing system, asphalt supply system, powder supply system, dust removal system, product silo and control system, etc. Some composition.

Modified Bitumen

The driving device is one of the important components of the asphalt mixing plant, so whether it can operate reliably must be highly valued to avoid adverse effects on the entire asphalt mixing plant. In order to ensure that the driving device in the asphalt mixing plant is indeed complete and reliable, the following maintenance measures are essential.

Synchronous gravel sealing in road maintenance can quickly improve road driving performance, repair anti-skid performance, smoothness, etc. It is used in preventive maintenance and is also one of the methods of low-grade road pavement construction. Synchronous gravel seal has the advantages of high strength, rough surface, non-slip, impermeable, good durability, and prevention of water mist when driving on rainy days. The so-called synchronous gravel sealing layer is to use special equipment, namely the synchronous gravel sealing truck and the bonding material (modified asphalt or modified emulsified asphalt) to be spread simultaneously on the road surface, and the single layer of asphalt wear is formed by natural driving or rolling with a road roller. layer, mainly used as asphalt surface layer.

Asphalt mixing plants are large-scale products with high professional and technical requirements, and are composed of multiple systems. Among them, asphalt tanks are also a very critical part. Whether it is manufacturing, debugging or installation, it needs to be operated according to the actual application needs of users.
In addition to the manufacturing, debugging and installation, which need to be operated by installers, the maintenance of asphalt tanks in asphalt mixing plants must also be managed by professionals. At the same time, they must strictly follow all safety rules to operate. Before operation, they must be proficient in the relevant requirements and based on the regulations and safety instructions for storing and handling hot asphalt.

Asphalt mixing plant is also called asphalt mixture mixing equipment, which is mainly used to produce asphalt mixtures of various specifications. It is an important equipment in projects such as road construction, highway maintenance and airport runway construction. The main components of an asphalt mixing plant include cold material supply system, drying drum, screening system, weighing system, agitator, finished product silo and control system.
The workflow of an asphalt mixing plant is generally as follows:

Asphalt mixing equipment has a special function, which is that it can perform cyclic heating to make the asphalt product reach the best condition. But how does it achieve this function? Everyone is curious about this.

Natural gas is a colorless, odorless, flammable and explosive gas, the main component of which is methane, which accounts for about 98% of natural gas. The density of natural gas is lower than that of air and it is difficult to liquefy. Natural gas is not only a clean green energy for civil, commercial and industrial use, but also a raw gas for chemical industry. The theoretical ignition value of natural gas is 540 degrees, the combustion temperature is 1970 degrees, the calorific value is 40MJ/m3, and the explosion limit is 5%-15%. CNG refers to natural gas that has been compressed to 20-25MP and stored in high-pressure gas tank trucks, and then transported to various gas transmission points to supply gas to residential users, commercial users and industrial users. In order to ensure the normal operation and safety of the asphalt mixing station and our pressure regulating station, our company has specially formulated the following safety protection measures.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing plant also needs to be powered on for trial operation before it is officially put into work.
The first step in commissioning is to run a single motor and check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

In recent years, asphalt concrete, as a new green building material, is gradually being valued by people because of its excellent performance in saving resources, being environmentally friendly, ensuring the quality of construction projects, and achieving sustainable utilization of resources. The development of asphalt concrete fully embodies my country’s policies to achieve energy conservation and emission reduction, and is also an important measure to promote the development of circular economy.

Asphalt mixing plant is a relatively important complete set of equipment in people’s lives. There are many components of this equipment, such as grading machine, vibrating screen, belt feeder, powder conveyor, elevator and other parts. Plug valve is one of them, so what is the specific role of plug valve in asphalt mixing plant? This article will give a brief introduction.
The plug valve is first of all a closure or plunger-shaped rotary valve. Generally, it is necessary to rotate 90 degrees to make the channel opening on the valve plug the same as that on the valve body, or to split it to play the role of opening or closing. The shape of the plug valve in the asphalt mixing plant is generally cylindrical or conical.