The necessity of emulsified bitumen equipment in modern road construction projects

Everyone must be familiar with slurry sealing and micro-surfacing. But do you know their 7 construction steps?
Slurry sealing and micro-surfacing were both early preventative highway protection technologies. Its function is to ensure the smooth use and extended life of the highway. The construction steps are as follows:

Contemporary roads and pavements have undergone many changes: traffic volume and driving frequency have increased significantly, the axle load of logistics trucks has continued to increase, one-way driving in separate lanes has been widely implemented, and regulations have further improved the anti-flow resistance of the ground, that is, the work of modified asphalt equipment under high temperatures ability;

The viscosity of the drum bitumen decanter equipment decreases as the temperature increases during the production process. Its output viscosity is about twice as high as every 12°C increase. During production, the base bitumen decanter equipment must first be heated to a liquid state and then emulsified. In order to better integrate the emulsification ability of colloid milling, the viscosity of base bitumen decanter is generally controlled to be about 200 cst. The lower the temperature, the higher the viscosity, which increases the pressure on the bitumen decanter pump and colloid milling, making emulsification impossible: However, on the other hand, in order to prevent the bitumen decanter equipment from weaning when the moisture of the finished product evaporates, it is impossible to heat the base asphalt barrel removal temperature too high, and generally use a colloid grinding inlet and outlet system. The finished product temperature should be below 85°C.

When using asphalt melting equipment, you need to pay attention to the following points:
1. The power must be cut off during installation and operation to ensure safety.
2. Before starting operation, check whether all components are normal and have no fault prompts. In particular, the inspection of key parts such as the heater part and the conveyor belt device is particularly important.

Water is one of the raw materials of the modified asphalt storage tank, and it is distributed in various components of the modified asphalt storage tank equipment. According to the components where water is distributed, the anti-cold measures are explained one by one. The water tank of the modified asphalt storage tank, the water inside the water tank is released through the filter valve. Some instruments of the modified asphalt storage tank do not have a filter valve to save the cost of the equipment. The modified asphalt storage tank can only be drained by loosening the flange bolts at the bottom. The water pump of the modified asphalt storage tank mentioned here includes a hot water pump and a circulating water pump. This type of water pump for the modified asphalt storage tank generally uses a pipeline centrifugal pump. There is a sewage outlet at the bottom of the pipeline centrifugal pump. The modified asphalt storage tank pays attention to the sewage treatment of the sewage outlet at the bottom of the pump. The modified asphalt storage tank emulsion tank generally uses a cone bottom. However, in order to better process the modified asphalt storage tank coefficient, the inlet and outlet are usually not placed at the bottom of the modified asphalt storage tank. Emulsion (mostly water) will remain at the bottom of the tank, and this part of the residual liquid in the modified asphalt storage tank must be discharged through the filter valve at the bottom. Emulsion pump for modified asphalt storage tank There are basically two types of emulsion pumps for modified asphalt storage tank equipment on the market, gear pumps or centrifugal water pumps. Gear pumps can only discharge the liquid inside the pump through the connection flange of the pipeline. The centrifugal water pump for modified asphalt storage tanks uses its own sewage outlet for sewage treatment. The first four items of modified asphalt storage tanks with basic knowledge are basically discharged, and the modified asphalt storage tanks will focus on the latter types. Modified asphalt storage tank colloid mill There will also be residual emulsion or water inside the modified asphalt storage tank colloid mill. The gap between the stator and rotor of the colloid mill is within 1mm. If there is a little residual water in the modified asphalt storage tank, it will cause the accident of frozen modified asphalt storage tank. The residue in the colloid mill can be treated by loosening the connection bolts of the finished product pipeline.

From the current point of view, road construction machinery has bottomed out and asphalt meltering equipment has risen rapidly. In recent years, highway construction and maintenance departments have a strong awareness of using asphalt mixing equipment, especially in developed coastal areas such as Beijing, Shanghai, Jiangsu, Zhejiang, etc. In addition, these regions have a fast economic growth rate, relatively developed industry, and strong comprehensive economic strength. Therefore, the consumption of asphalt mixing equipments in these regions has always been at the forefront of the country. With the rapid development of highway construction and the increase in demand for asphalt, barreled asphalt has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported asphalt used in high-grade highways is in barrel form, which requires an asphalt meltering equipment with fast melting speed, clean de-barreling, and can prevent asphalt aging. my country’s highway construction has achieved remarkable results, among which mechanized production has contributed greatly. Different types of asphalt mixers and bitumen meltering equipment are selected for the characteristics of large highway pavement construction and tight construction period. With the rapid development of my country’s economy, the further extension of expressways, and the large-scale development of western construction, the central and western regions have become new investment hotspots. While paying attention to the market in the developed eastern regions, domestic road construction machinery manufacturers have also increased their efforts to develop the central and western markets, creating new highlights for the domestic asphalt mixing plants consumer market. In summary, my country’s asphalt mixing plant sales market has begun to move westward with the westward movement of investment hotspots. As the market center of gravity gradually shifts westward, the market in the western region is gradually heating up. The self-heating integrated structure, hot air barrel melting and bitumen barrel flipping technology in the asphalt barrel removal equipment are our company’s self-heating integrated structure. The thermal oil furnace used in the old equipment is perfectly integrated with the asphalt barrel removal equipment body, which reduces the volume of the entire set of equipment, greatly reduces equipment investment, saves equipment space and transfer transportation costs.

Colored asphalt pavement is a kind of special pavement material that mixes colored particles into asphalt and then lays on the pavement

The base layer of asphalt pavement is divided into semi-rigid and rigid. Since the base layer and the surface layer are materials of different properties, good bonding and continuity between the two are the key requirements for this type of pavement. In addition, when the asphalt surface layer seeps water, most of the water will be concentrated at the joint between the surface layer and the base layer, causing damage such as slurry, looseness, and potholes to the asphalt pavement. Therefore, adding a lower seal layer on top of a semi-rigid or rigid base layer will play a vital role in enhancing the strength, stability and waterproofing capabilities of the pavement structural layer. The more commonly used one is to use asphalt gravel synchronous sealing technology.
So let’s take a look at how the construction of the asphalt gravel synchronous sealing truck is carried out:

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing station also needs to be powered on for trial operation before it is officially put into work.

Fog seal is an asphalt pavement maintenance construction method.
When the asphalt pavement has increased water permeability, loss of fine aggregate, cracks, pitting, etc., a fog seal layer can be used for pavement repair. The bonding material of the fog seal layer is fluid, can repair cracks and gaps, and can heal cracks below 0.3. After construction, the oil content of the road surface is increased, the anti-sticking aggregate is loosened, and it can play a waterproof role.
Before construction, the original road surface should be surveyed and analyzed to determine the construction bonding materials and spray volume.
So what precautions should be taken during construction?

Bitumen emulsifier is a surfactant. A surfactant is a compound that reduces the surface tension between two liquids, a gas and a liquid, or a solid and a liquid. Surfactants are mainly used in: detergents, detergents, fabric softeners, wetting agents, emulsifiers, foaming agents, dispersants, adhesives, etc.

To ensure good operation of asphalt melting equipment and extend its service life, regular maintenance and repairs are required. The following are specific maintenance and repair steps:
First, various parts of the equipment, including heating elements, pipes, valves, etc., need to be inspected regularly to make sure they are not worn or damaged. If any problems are found, they should be repaired or replaced immediately.

Modified (rubber powder) bitumen equipment, one of the road maintenance equipment. It is a kind of equipment that measures, mixes and develops SBS, rubber powder and asphalt.
Modified (rubber powder) bitumen equipment is a set of wet modification processing technology, which mainly consists of modified material metering and promotion, bitumen rapid heating, asphalt metering, high-intensity mixing tank, mixed material transfer pump, development tank, colloid mill, Control system and other components.

Some of the equipment of emulsified modified bitumen equipment are as follows. The specially made bitumen filter can effectively filter the residues and dirt in the high-temperature culture medium bitumen to avoid damage to the subsequent equipment. The emulsified modified bitumen equipment adopts a spiral plate type or a shell and tube heat exchanger to quickly heat the culture medium bitumen through high-temperature heat transfer oil to meet the needs of the production process. The emulsified modified bitumen equipment is heated in the storage tank to prevent the bitumen from aging due to long-term high-temperature heating and exposure to the air. The sulfate generated during the production process of the emulsified modified bitumen equipment is very limited, reducing air pollution.
The emulsified modified bitumen equipment sends the modified material manually poured into the dumping bin to the bitumen batching tank by wind or spiral. It can be equipped with a metering and calibration system. The emulsified modified bitumen equipment thickener is automatically or manually added. The emulsified modified bitumen equipment can be equipped with a metering and calibration system. Emulsified modified bitumen equipment transportation and metering and calibration system, the emulsified modified bitumen equipment adds the set bitumen amount to the batching tank through the frequency converter and computer interlock. The emulsified modified bitumen equipment and bitumen steam flowmeter use big brand products to ensure the preparation.

Improve the reliability of SBS bitumen emulsion plants: Once you have an established maintenance, it will help to identify problems. This will allow the maintenance plan and time to be carried out at your convenience. Regular maintenance will increase the normal operation time of SBS bitumen emulsification equipment, and it can be used when necessary. Low cost of operation: Imagine an SBS bitumen emulsification plant breaks down during a project. With a protective maintenance plan, such things happen less often because you have taken good care of the SBS bitumen emulsification plant.
If the SBS bitumen emulsification plant wants to maintain normal operation, then in the production process. All stages need to be maintained normal, among which the normality of the circuit system is an important aspect to ensure its smooth operation. Imagine that if there is a problem with the circuit during the on-site operation, it may affect the development of the entire project.
For users, of course, they don’t expect this to happen, so if the SBS bitumen emulsification plant is in the work of using the SBS bitumen emulsification equipment, if there is a circuit problem, it is necessary to take appropriate measures to solve it in time. The following article will give a detailed description of this problem, and the following SBS bitumen emulsification plant can be of benefit to everyone.

Before use, please check whether the position of each valve is accurate and make preparations before work. After starting the motor of the asphalt spreading truck, check the four thermal oil valves and air pressure gauge. After everything is normal, start the engine and the power take-off starts to work. Try running the asphalt pump and cycle for 5 minutes. If the pump head shell is hot to your hands, slowly close the thermal oil pump valve. If the heating is insufficient, the pump will not rotate or make noise. You need to open the valve and continue to heat the asphalt pump until it can operate normally.

The difficulty of emulsified bitumen equipment itself, because general bitumen also has different classifications, in the production and processing of emulsified bitumen equipment bitumen concrete, it is necessary to pay attention to whether the common raw materials are the common bitumen and ensure the quality. Check the black antistatic tweezers of emulsified bitumen equipment asphalt concrete machine equipment emulsified bitumen equipment.
If the gap of the black antistatic medical tweezers bitumen concrete micro-powder machine of emulsified bitumen equipment is enlarged after long-term use, then we can adjust it and continue to process it. Emulsified bitumen equipment is a relatively simple difficulty.

Asphalt used to pave roads. It can be obtained by regular vacuum distillation of crude oil with appropriate properties, and can also be obtained by shallow oxidation of vacuum residue or propane deasphalting process. It can also be prepared by mixing asphalt of different duction and injection degree

Synchronized gravel sealing is a process technology for treating cracks in asphalt pavement, and it is currently a road construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical features are? If you don’t know, just follow the editor of Sinoroader and take a look.

What is the overall operation process of bitumen (composition: asphaltene and resin) drum melting equipment?
The bitumen (composition: asphaltene and resin) drum melting equipment produced by our company mainly uses barrel debarking and melting of large barrels of bitumen (definition: the transformation process of materials from solid to liquid), using high-temperature thermal oil as the material (playing a decision-making role substance), used in supporting facilities of high-temperature thermal oil heating equipment. Bitumen drum melter equipment has the functions of barrel delivery, barrel removal, storage, temperature raising, slag discharge, etc. It is an essential product for high-grade highway construction companies. Bitumen drum melter equipment can be used for resin barrel removal. The bitumen drum melter equipment mainly consists of barrel removal shell, hoisting mechanism, hydraulic booster and electrical control system.

Asphalt sealant is a material specially used for road crack repair. The following is a detailed introduction to asphalt sealant:
1. Definition and composition
Asphalt sealant is a road repair material made of asphalt or modified asphalt as the base material, with a certain amount of additives and fillers added, and processed by special technology. It usually has a black or dark brown appearance and is in a solid or semi-solid form.
2. Main characteristics
High adhesion: Asphalt sealant can firmly bond to the crack wall of the road surface to form a tight sealing layer to prevent moisture and other harmful substances from invading the road surface structure.
High elasticity: It has a certain elastic recovery ability and can adapt to the expansion and contraction changes of the road surface to prevent further expansion of cracks.
Weather resistance: After special process treatment, it has good weather resistance and can maintain its stable performance for a long time.
Convenient construction: The construction operation is simple and fast, without complex construction machinery, which reduces the construction cost.
3. Scope of application
Asphalt sealant is widely used in crack repair of various asphalt pavements, including highways, urban roads, airport runways, etc. At the same time, it can also be used for the maintenance and repair of asphalt surfaces such as bridges, tunnels, and parking lots.

Is the performance of Sinoroader’s fully automatic emulsified asphalt production equipment stable and unstable? To be honest, whether the performance of a product is stable or not can only be known through practice, right?
Chairman Mao, the great leader of China, once said, “Without practice, there is no right to speak.” Yes, people who have never used it naturally have no right to speak. Now the editor will talk about the fully automatic emulsified asphalt production equipment that I am using!

Due to the incorporation of a certain proportion of water into the slurry sealing mixture, it is easy to evaporate in the air. After the water is evaporated, it will become dry and hardened. Therefore, after the slurry is formed, it not only looks very similar to fine-grained asphalt concrete, but does not affect the visual appearance of the road. It also has the same technical properties as fine-grained concrete in terms of wear resistance, anti-skid, waterproofing, and smoothness. Slurry seal technology is used in highway pavement maintenance because of its simple construction technology, short construction period, low cost, high quality, wide application, strong adaptability, etc. It is an asphalt with both economy and high efficiency. Pavement maintenance technology is worthy of application and promotion.

Synchronous chip seal is a process technology for treating cracks in asphalt pavement, and it is currently a highway construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical characteristics are? If you don’t know, follow the editor of Sinoroader company to have a look.

The main filter material of stainless steel barrel removal adopts five-layer sintered mesh. Standard five-layer calcination is made by stacking and vacuum calcining five layers of stainless steel barrel removal wire mesh. The stainless steel barrel made of it has corrosion resistance, good water permeability, high compressive strength, easy cleaning and back-cleaning, high filtration precision, hygienic and clean filter material, and stainless steel barrel removal wire mesh does not fall off.
Double-layer metal sintered mesh is a new type of filtration system with high impact toughness and overall rigidity, which is made by stacking and vacuum calcining double-layer stainless steel barrel removal wire mesh products.

Whether it is the application of modified asphalt equipment or the application of other equipment, if you want to extend its service life, you need to do daily maintenance work. In order to better help everyone, we have modified asphalt The maintenance methods that can be adopted when using the equipment are introduced as follows:

Asphalt emulsifier is an emulsifier that belongs to the category of surfactants and is a raw material for the production of emulsified asphalt.
Emulsifiers are divided into: synthetic emulsifiers, natural emulsifiers, inorganic powder emulsifiers, etc. Currently, synthetic emulsifiers are widely used. Asphalt emulsifier is a type of chemical organically synthesized surfactant.

Emulsified asphalt (ingredients: asphaltene and resin) heating tank is a new type of equipment for heating emulsified asphalt. Its appearance replaces the traditional thermal oil heating equipment, which brings great convenience to our users and improves work efficiency. Then let’s take a detailed look at how it is better than the traditional thermal oil heating equipment.
Emulsified asphalt (ingredients: asphaltene and resin) heating tank is another new type of emulsified asphalt heating storage equipment developed by technically separating the characteristics of traditional thermal oil heating emulsified asphalt tanks and internal heat part (part) rapid emulsified asphalt heating tanks. The automatic circulation program of the asphalt heating equipment enables the asphalt to automatically enter the heater, dust collector, induced draft fan, asphalt pump, asphalt temperature display, water level display, and steam generator as required.
It consists of pipeline and asphalt pump preheating system, pressure relief system steam combustion system, tank cleaning system, oil unloading tank installation, etc. All are installed on the tank body (inside) to form a compact integrated structure. It fully compensates for the shortcomings of traditional thermal oil heating equipment, such as long heating time and high energy consumption.