Three key questions about asphalt mixing equipment in road construction machinery

Safety is the key point for any piece of equipment, and asphalt mixers are of course no exception. What I want to share with you is the knowledge in this area, that is, the safe operation specifications of asphalt mixers. You might as well pay attention to it.
In order to prevent the asphalt mixer from moving during work, the equipment should be placed in a flat position as much as possible, and at the same time, use square wood to pad the front and rear axles so that the tires are elevated. At the same time, the asphalt mixer must be provided with secondary leakage protection, and it can only be started after the inspection, trial operation and other aspects are qualified.

The basic working principle of the green asphalt mixing plants can be roughly summarized in the following ways:
To put it simply, an asphalt plant is actually a set of equipment that can mix several materials according to a predetermined ratio to form a relatively uniform mixture. It is currently widely used and is very important for the construction of different projects. Its performance Various aspects also have a great impact on the engineering quality of asphalt pavement.
Asphalt mixing plant equipment is usually divided into two structures. The intermittent type is relatively more complex in structure and process. The aggregates need to be screened twice and then measured in batches. The batching accuracy is higher. , the mixing quality is good and can meet different construction requirements. The continuous type has a slightly lower accuracy due to its simple structure and simplified operating procedures.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing station also needs to be powered on for trial operation before it is officially put into work.
At the beginning of the test run, first run a single motor, and at the same time check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

1: The site should be located on higher ground and away from residential areas and densely populated areas.
2: The venue should consider the transportation distance and choose a location with convenient transportation.
3: Determine the website construction plan according to the terrain

Asphalt flue gas treatment methods, their principles and characteristics, and an asphalt flue gas environmental protection treatment plan based on the actual asphalt flue gas problems faced by the unit.

1. Basic situation
My unit’s mixing plant is equipped with a 4000-type asphalt mixing plant. During daily production of the asphalt mixing plant, a large amount of asphalt smoke will be emitted from the mixing pot discharge port. This smoke not only has an unpleasant smell, but also contains A large number of compounds that are harmful to the human body, such as benzopyrene, benzanthracene, carbazole and other polycyclic aromatic hydrocarbons, mostly have carcinogenic risks. Smoke overflow will cause pollution to the surrounding atmospheric environment and affect the personal health of workers. Although the overflow port of the mixing station is equipped with a dust retaining wall, the fine dust is seriously raised, and the cold material belt conveyor is dusty. In order to protect the environment, reduce pollution, and reduce cost investment, based on full research and absorption of technology in the same industry, and combined with the actual situation of asphalt mixing, we are planning to install asphalt mixing bag dust collectors to the flue at the discharge port of the mixing pot to control asphalt fumes. Gas is processed. The dust removal efficiency of the bag dust collector can reach 97%~99%, and the dust-containing gas can be purified to a level of 50mg/Nm3.

Asphalt mixing stations are constructed according to a certain process, which can not only ensure the construction quality, but also ensure that the asphalt mixing station is not damaged. Although construction details are critical, the key skills of asphalt mixing station construction must be mastered.
Before the construction of the asphalt mixing plant, the top surface of the asphalt mixing station construction range should be removed, and the site elevation should be kept dry and flat to meet the design requirements. If the surface is too soft, the foundation should be reinforced to prevent the construction machinery from losing stability and ensure that the pile frame is vertical.
Then the on-site construction machinery should be inspected to ensure that the machinery is intact and assembled and tested under the premise of meeting the requirements. To ensure the verticality of the asphalt mixing plant, the deviation of the gantry guide and the mixing shaft from the verticality of the ground shall not exceed 1.0%. Asphalt mixer manufacturer.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing plant also needs to be powered on for trial operation before it is officially put into work.
The first step in commissioning is to run a single motor and check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

Asphalt mixing equipment is also divided into fixed and mobile types. There are still big differences between the two to a certain extent. Let’s take a look at the design of mobile asphalt mixing equipment. What advantages can bring to the equipment?

When an ordinary asphalt mixing station completes the mixing operation, it will cause great pollution to the surrounding environment. In order to solve this problem, environmentally friendly asphalt mixing equipment came into being. What are the characteristics of this type of equipment?

[1]. Composition of intermittent asphalt mixing plant
The intermittent asphalt mixing plant mainly consists of cold material silo, cold material distribution system, cold material conveying system, combustion and drying system, ventilation and dust removal system, hot material elevator, vibrating screen, hot material silo, powder conveying system and asphalt conveying system. System, metering system, mixing cylinder, control system, finished material transportation and storage system, asphalt heating and insulation system, etc.
2. Discussing the phenomenon of warehouse cascading in asphalt concrete mixing plants
2.1 First, let’s introduce the structure and principle of vibrating screen. The main components include: RetentionRubber, SupportTube, vibrating screen drive system and supporting electrical components
The working principle is introduced as follows: hot aggregate is sent to the vibrating screen through the hot aggregate elevator, and the hot aggregate is vibrated and screened by the vibrating screen. Stones of different specifications enter their corresponding hot aggregate bins through the screen and cannot pass through the geotechnical work. The super-sized particles from the cloth screen enter the overflow bin and are sent out.

Asphalt mixing stations, also known as asphalt concrete mixing stations, can produce asphalt mixtures, modified asphalt mixtures, and colored asphalt mixtures, which fully meet the needs of building highways, grade roads, municipal roads, airports, ports, etc. Changmeng Electric Power introduces the safety operating procedures of asphalt mixing plants below:
1. During the operation of the mixing equipment, in addition to ensuring that the equipment is in good condition, it should also be equipped with a mineral moisture content detector and a finished material tester, and the relevant data should be frequently tested for the operator to adjust the operation in time to keep the equipment in good condition.
2. In addition to affecting production capacity, the moisture content of mineral materials is also the main factor determining fuel consumption. Additional material sheds should be added.
3. Before operation, all working parts and devices of the mixing equipment should be fully checked to see if they are intact and normal. If there are any problems, they must be properly handled before operation, and it is forbidden to operate with illness.
4. The operation must be carried out strictly in accordance with the procedures and precautions specified in the instruction manual. After normal ignition, the dust collector should be monitored to ensure that the drying drum burns under negative pressure; after production starts, the hot material elevator and agitator should be monitored to see if they are working normally to coordinate the operation of other parts.

Synchronous gravel sealing in road maintenance can quickly improve road driving performance, repair anti-skid performance, smoothness, etc. It is used in preventive maintenance and is also one of the methods of low-grade road pavement construction. Synchronous gravel seal has the advantages of high strength, rough surface, non-slip, impermeable, good durability, and prevention of water mist when driving on rainy days. The so-called synchronous gravel sealing layer is to use special equipment, namely the synchronous gravel sealing truck and the bonding material (modified asphalt or modified emulsified asphalt) to be spread simultaneously on the road surface, and the single layer of asphalt wear is formed by natural driving or rolling with a road roller. layer, mainly used as asphalt surface layer.

Natural gas is a colorless, odorless, flammable and explosive gas, the main component of which is methane, which accounts for about 98% of natural gas. The density of natural gas is lower than that of air and it is difficult to liquefy. Natural gas is not only a clean green energy for civil, commercial and industrial use, but also a raw gas for chemical industry. The theoretical ignition value of natural gas is 540 degrees, the combustion temperature is 1970 degrees, the calorific value is 40MJ/m3, and the explosion limit is 5%-15%. CNG refers to natural gas that has been compressed to 20-25MP and stored in high-pressure gas tank trucks, and then transported to various gas transmission points to supply gas to residential users, commercial users and industrial users. In order to ensure the normal operation and safety of the asphalt mixing station and our pressure regulating station, our company has specially formulated the following safety protection measures.

Asphalt mixing plant refers to a complete set of equipment used for batch production of asphalt concrete. Its main function is to produce asphalt mixture, colored asphalt mixture, etc., and has been widely used in road construction. However, during the production process of asphalt mixture, pollutants such as noise, dust, and asphalt smoke will be produced, seriously polluting the environment and threatening the health of workers. Therefore, under the current background of building a resource-saving and environment-friendly society in our country, it is very important to save energy and reduce consumption during the use of asphalt mixing plants. The following article mainly starts from the three factors that affect the asphalt mixing plant, and explores the energy saving and consumption reduction measures of the asphalt mixing plant, aiming to reduce the cost of asphalt production and improve the efficiency of the asphalt plant.

The mobile forced asphalt mixing equipment adopts intermittent drying cylinder, double forced mixer, the main machine can be towed, small footprint, short installation cycle, convenient operation and maintenance, good stability, high degree of automation, high degree of standardization, and high quality of finished products, and the technology of continuous improvement. The mobile forced asphalt mixing plant is suitable for high-grade road asphalt paving and maintenance.
1. The combined structure of the drum dryer and the batching machine is installed on a movable bracket for easy movement.
2. The asphalt mixing plant is equipped with a double horizontal shaft to boil the aggregate and ensure uniform mixing.
3. In the densely arranged hanging barrels, the hot aggregate rises vertically. This lifting tool is easy to use and reliable.
4. For accurate weighing of aggregates, asphalt and powder ore, a measuring scale is used, which contains a weighing sensor for electronic measurement.
5. The movement of the power material follows a closed spiral path, which ensures little material loss and provides safe transfer.
6. On the cyclone burner, high-pressure oil is sprayed out and quickly atomized. In the combustion chamber, the material is fed in a spiral manner and automatically ignited by the oil mist, which ensures combustion efficiency. The cylindrical barrel of the burner is separated from the burner head. The furnace cavity can be pushed in and pulled out, which is convenient for replacing the damaged side column bricks inside the burner. The entire burner has a large heat capacity and high thermal strength. This is cost-effectiveness.

Asphalt mixing equipment is equipment used to produce asphalt concrete in large quantities. Because this equipment is affected by various factors during the production process, some problems will inevitably occur after a period of use. Sinoroader Group The editor of the asphalt mixing equipment company of China Machinery Co., Ltd. will introduce to you the methods of rescuing damaged parts in asphalt mixing equipment.
Asphalt mixing equipment encounters different problems, and the solutions are also different. For example, one of the common problems of asphalt mixing equipment is that parts are worn out and damaged. The solution that needs to be done at this time is to start from the production of parts. Just start improving.

Asphalt mixing equipment is a large-scale equipment, so you must pay attention to safety when using it to avoid accidents. But to put it simply, if you want to truly use it safely, you must master some basic common sense. The following main things must be kept in mind.

The development prospects of asphalt mixing plants are very good, and the product competition on the market is also very fierce. When the equipment is used, uneven wear of the supporting wheels and wheel rails often occurs, and sometimes there are some abnormal noises and edge gnawing. The main reason is that after the asphalt mixing station has been working for a period of time, the drying cylinder is exposed to high temperature and friction occurs between the supporting wheel and the wheel rail.
Under the action of drying materials in an asphalt mixing station, the equipment will vibrate violently, which will directly lead to improper adjustment of the gap between the wheel rail and the supporting wheel, or mutual interference between the two. The position is skewed, so the operator needs to add grease to the surface contact positions of the supporting wheel and the calibrating wheel rail after every day’s work.

Judging from the situation of highways in our country, asphalt pavement is the most used, which is one of the reasons why asphalt mixing plants have developed so rapidly. Under the situation of rapid economic development, the quality problems of asphalt pavement are gradually increasing, which puts forward higher and higher requirements for the quality of asphalt. It is understood that the primary factor that affects the quality of asphalt is the ratio of raw materials. This is also covered in the introduction of asphalt mixing stations. You can discuss it together.
In order to obtain high-quality asphalt products, in addition to the asphalt mixing equipment meeting the requirements, selecting the appropriate asphalt mixture gradation type is also a top priority. According to my country’s current regulations, the maximum particle size of the asphalt mixture in the upper layer of the highway should not exceed half of the layer thickness; while the maximum particle size of the aggregate in the middle surface layer of asphalt mixture should not exceed two-thirds of the layer thickness; and the asphalt layer should not exceed half of the layer thickness. The maximum nominal aggregate size of the pavement structural layer mixture should not exceed one-third of the layer thickness.
Based on this analysis, if an asphalt surface layer with a certain thickness is selected according to the above specifications, the particle size of the asphalt mixture aggregates will generally be larger, which will inevitably bring insurmountable construction difficulties to the construction of asphalt concrete pavement. After investigation, testing, analysis, and comparison, it can be seen that the lower layer has a wider choice, so the AG-201 gradation type can be used; while the selection of the upper layer mixture type is more difficult, and it is necessary to achieve a reasonable choice of this mix ratio. , on the one hand, we must examine as many aggregate resources as possible, and on the other hand, we must also consider the model of the mixing equipment.
In order to ensure the quality of the project, strict selection and inspection of engineering materials must be carried out. Therefore, the selection and determination of raw materials should be based on the requirements for pavement structure and use quality, combined with the supply of floor materials, and inspection in accordance with the requirements of relevant test procedures, and then Select the best materials so that all technical indicators of the materials meet the specified technical requirements.

Due to its complexity and importance, asphalt mixing plants are more critical in road construction. Modern asphalt mixing stations have five key systems. Do you know what they are?
1. Mixing system of asphalt mixing plant
Mixing equipment is one of the key systems, why? Usually, the productivity of the mixing equipment has a great impact on the next step of construction efficiency. Most asphalt mixing plants use twin-shaft forced mixing. Since the drying drum and burner of the mixing equipment have strong overload capabilities, and in most cases, the moisture content of the mineral materials is less than 5%, this improves the productivity of the mixing equipment. provide conditions. The mixing blades of the mixer have an adjustable assembly angle and are driven by dual mixing shafts and dual motors.

Colored asphalt pavement is a kind of special pavement material that mixes colored particles into asphalt and then lays on the pavement

After use, asphalt mixing equipment needs to be disassembled, cleaned, and maintained before it can be saved for next use. Not only is the disassembly process of the equipment important, but the previous preparation work also has a greater impact, so it cannot be neglected. Please pay attention to the detailed introduction below for specific content.

Safety is the key point for any piece of equipment, and asphalt mixers are of course no exception. What I want to share with you is the knowledge in this area, that is, the safe operation specifications of asphalt mixers. You might as well pay attention to it.

The quality of asphalt mixture directly determines the quality of asphalt pavement engineering. This article discusses the key points of supervision of ordinary highway asphalt plants in order to better monitor the quality of asphalt mixture.

In my country, most of the raw materials used in highway construction are asphalt, so asphalt mixing plants have also developed rapidly. However, under the situation of rapid economic development in my country, the problems of asphalt pavement have gradually increased, so the market requirements for asphalt quality have become higher and higher.
There are many factors that affect the quality of asphalt. In addition to the need for asphalt mixing plant equipment to meet conventional requirements, the ratio of raw materials is also very important. At present, my country’s existing industry specifications indicate that the maximum particle size of the asphalt mixture used on the upper layer of the highway cannot exceed half of the thickness, and the maximum particle size of the aggregate of the middle asphalt mixture cannot exceed two-thirds of the thickness of the layer, and the maximum size of the structural layer cannot exceed one-third of the same layer.

The application of asphalt mixing plants also involves selection issues. In order to give full play to the performance of the equipment, the model of the machine is mainly determined according to the actual situation of the construction site. It sounds relatively simple, but some details still need to be emphasized.
The so-called specific conditions of the construction site first include the size of the site; secondly, the properties, specifications and working dimensions of the enterprise’s supporting equipment. It is necessary to try to do a good job in all aspects to help improve production efficiency and ensure product quality. In the case of intensive network management, the network management function of the asphalt mixing plant must also be taken into account to avoid difficulties in future upgrades.

There is also a reversing valve in the asphalt mixer, which generally does not cause problems, so I have not understood its solution in detail before. But in actual use, we encountered this kind of failure. How should we deal with it?

In recent years, asphalt concrete, as a new green building material, is gradually being valued by people because of its excellent performance in saving resources, being environmentally friendly, ensuring the quality of construction projects, and achieving sustainable utilization of resources. The development of asphalt concrete fully embodies my country’s policies to achieve energy conservation and emission reduction, and is also an important measure to promote the development of circular economy.

Asphalt mixing plant is a very practical engineering machinery. Especially in the road construction process, it plays an irreplaceable role. Due to its importance, in addition to ensuring its own quality, the use and maintenance of the equipment must be carried out normally. Let’s learn about the daily maintenance requirements of asphalt mixing plants.