What are the advantages of synchronous gravel sealing truck for road maintenance?

1. Observation: Pay attention to the dynamics of the road surface after milling (three to four days), and pave the milled and roughened road surface in time when paving conditions are met.
2. On-site mixing: During construction and production, a sealing slurry truck should be used for on-site mixing. Through the metering equipment of the sealing truck and on-site operation by a robot, it is ensured that emulsified asphalt, water, mineral materials, fillers, etc. can be mixed according to a certain proportion. , stir through the mixing box, and the paving thickness is not higher than the roughing depth.

The requirements for SBS asphalt emulsification equipment are very high. The micro powder machine must have a sufficiently large driving force and can bear the condensation type. Because the temperature requirements of the emulsion SBS asphalt process are relatively high, the emulsified asphalt should be passed through a heat exchanger before feeding to reduce the emulsified asphalt temperature to below 90°C to prevent the emulsified asphalt from breaking due to excessive temperature.
The application scope of SBS modified emulsified asphalt is very wide. According to the nature of the construction, it can be used in new construction, renovation, and reconstruction projects; according to the nature of the project, it can be used in overhaul, equipment overhaul, and maintenance projects. Among them, the actual application projects include micro-surfacing, cold regeneration, cold mixing and cold paving, adhesive layer, permeable oil, slurry seal, gravel permeable layer, fog permeable layer, road moisture-proofing, SBS membrane, ground seam filling, and all other projects that can use emulsified asphalt.

The selection of asphalt melting equipment should take into account factors such as the use environment, working conditions, and technical requirements. Common ones include hot oil heating equipment, electric heating equipment, and gas heating equipment.
Hot oil heating equipment is suitable for occasions that require long-term heating and high temperature control accuracy;
Electric heating equipment is suitable for small projects or occasions where temperature control accuracy is not required;
Gas heating equipment has the advantages of simple operation and low cost, but safety protection measures must be strictly followed.
When choosing, it is also necessary to comprehensively consider factors such as economy and environmental protection.

Precautions during the production of emulsified bitumen equipment. How much do you know about this information? Let’s learn more about it:
When the emulsified bitumen equipment is in production, the viscosity of the bitumen decreases with the increase of temperature. For every 12℃ increase, its dynamic viscosity decreases by about one time. During production, the base bitumen should be heated to liquid state before emulsification. In addition, in order to adapt to the emulsification capacity of the colloid mill, the base bitumen dynamic viscosity is generally controlled to be about 200cst. The lower the temperature, the higher the viscosity, which increases the burden on the bitumen pump and the colloid mill, making it difficult to emulsify; but on the other hand, in order to prevent the demulsification caused by excessive vaporization and evaporation of water in the finished product during the production of emulsified bitumen, it is impossible to heat the base bitumen temperature too high. Generally, the finished product temperature at the outlet of the colloid mill should be controlled to be less than 85℃.

With the rapid development of our country’s social development and the continuous development of economic and information technology, modern highway construction is also developing rapidly, and the requirements for ground structural materials are becoming higher and higher, and Asphalt concrete bonding raw materials are inseparable from modified asphalt equipment. So besides these influencing factors, what other reasons does the company have that people don’t understand? Let’s analyze it together.
There are some asphalt concrete equipment on the market, because they have not solved the problem of asphalt clogging before grinding, there are not enough preparation equipment and grinding equipment, the structure is unscientific, and the entire grinding process cannot achieve a certain particle size, resulting in modification. The product productivity of asphalt equipment is low and the product quality is unstable. It requires continuous grinding for a long time, creating problems. This will not only greatly increase energy consumption, increase costs, make product quality unstable, and affect the speed of highway construction.

Modified material bitumen stripper, if the definition is simple, is an bitumen stripper. If described in detail, modified materials such as rubber powder or other fillers are added to the bitumen stripper, or an bitumen stripper is used to Block chemical substances such as photooxygen catalysis. The first is to change the chemical composition of the bitumen stripper, and the second is to use modified materials to equip the stripper with a certain spatial network structure, thereby improving its performance. Modified bitumen strippers mainly include vulcanized rubber and thermoplastic polyurethane elastomer modified bitumen strippers, plastic and anti-corrosion coating modified bitumen strippers and polymer modified bitumen strippers.

I believe everyone is familiar with the relevant knowledge about modified bitumen equipment. As users continue to increase its application, we have also talked about it a lot in the above articles and learned that it is mainly engaged in the production of modified bitumen. Production, in order to further enhance users’ understanding of it, professionals summarize its relevant characteristics as follows:

Asphalt emulsifier is an emulsifier that belongs to the category of surfactants and is a raw material for the production of emulsified asphalt.
Emulsifiers are divided into: synthetic emulsifiers, natural emulsifiers, inorganic powder emulsifiers, etc. Currently, synthetic emulsifiers are widely used. Asphalt emulsifier is a type of chemical organically synthesized surfactant.

Asphalt used to pave roads. It can be obtained by regular vacuum distillation of crude oil with appropriate properties, and can also be obtained by shallow oxidation of vacuum residue or propane deasphalting process. It can also be prepared by mixing asphalt of different duction and injection degree

Here is an introduction to the knowledge on construction quality control of modified rubber asphalt equipment. Let’s introduce this knowledge from three aspects. The details are as follows: The viscosity of the modified asphalt mixture of modified rubber asphalt equipment is relatively high, and the construction temperature of each process is The construction temperature requirements are higher than those of ordinary asphalt mixtures.

Water is one of the raw materials of the modified asphalt storage tank, and it is distributed in various components of the modified asphalt storage tank equipment. According to the components where water is distributed, the anti-cold measures are explained one by one. The water tank of the modified asphalt storage tank, the water inside the water tank is released through the filter valve. Some instruments of the modified asphalt storage tank do not have a filter valve to save the cost of the equipment. The modified asphalt storage tank can only be drained by loosening the flange bolts at the bottom. The water pump of the modified asphalt storage tank mentioned here includes a hot water pump and a circulating water pump. This type of water pump for the modified asphalt storage tank generally uses a pipeline centrifugal pump. There is a sewage outlet at the bottom of the pipeline centrifugal pump. The modified asphalt storage tank pays attention to the sewage treatment of the sewage outlet at the bottom of the pump. The modified asphalt storage tank emulsion tank generally uses a cone bottom. However, in order to better process the modified asphalt storage tank coefficient, the inlet and outlet are usually not placed at the bottom of the modified asphalt storage tank. Emulsion (mostly water) will remain at the bottom of the tank, and this part of the residual liquid in the modified asphalt storage tank must be discharged through the filter valve at the bottom. Emulsion pump for modified asphalt storage tank There are basically two types of emulsion pumps for modified asphalt storage tank equipment on the market, gear pumps or centrifugal water pumps. Gear pumps can only discharge the liquid inside the pump through the connection flange of the pipeline. The centrifugal water pump for modified asphalt storage tanks uses its own sewage outlet for sewage treatment. The first four items of modified asphalt storage tanks with basic knowledge are basically discharged, and the modified asphalt storage tanks will focus on the latter types. Modified asphalt storage tank colloid mill There will also be residual emulsion or water inside the modified asphalt storage tank colloid mill. The gap between the stator and rotor of the colloid mill is within 1mm. If there is a little residual water in the modified asphalt storage tank, it will cause the accident of frozen modified asphalt storage tank. The residue in the colloid mill can be treated by loosening the connection bolts of the finished product pipeline.

There are certain standards for the composition and mix ratio of micro-surfacing, and a wide range of materials are used, including polymer-modified emulsified asphalt, various aggregates, cement, water, additives, etc. Raw material quality has a significant impact on microsurfacing performance, so understanding the performance of each component and the key factors that influence its performance is critical to ensuring the quality of your microsurfacing mix.

Whether it is the application of modified asphalt equipment or the application of other equipment, if you want to extend its service life, you need to do daily maintenance work. In order to better help everyone, we have modified asphalt The maintenance methods that can be adopted when using the equipment are introduced as follows:

1 Common diseases of asphalt pavement
There are nine phenomena of early damage to asphalt pavement: rutting, cracks, and potholes. These diseases are the most common and serious, and are one of the common quality problems of highway projects.
1.1 Rutting
Rutting refers to the longitudinal strip grooves on the road surface along the wheel tracks, with a depth of more than 1.5cm. Rutting is a strip groove formed by the accumulation of permanent deformation of the road surface under the repeated action of vehicle load. Rutting reduces the smoothness of the road surface. When the rutting reaches a certain depth, due to the accumulation of water in the rutting, it is easy for cars to slide and cause traffic accidents. The main reasons for rutting are unreasonable design and serious overloading of vehicles.
1.2 Cracks
There are three main forms of cracks: longitudinal cracks, transverse cracks and mesh cracks. When cracks occur in asphalt pavement, water seepage occurs, which harms the surface layer and base layer.
1.3 Potholes
Potholes are common early diseases of asphalt pavement, which refer to the road surface being damaged into potholes with a depth of more than 2cm and an area of ??more than 0.04㎡. The main reason for the formation of potholes is that the oil used in vehicle repair or motor vehicles seeps into the road surface, polluting the asphalt mixture and causing it to loosen. The pits are gradually formed by driving and rolling.

There are many types of emulsified asphalt (composition: asphaltene and resin) equipment. Emulsified asphalt (composition: asphaltene and resin) equipment can be divided into intermittent operation type, semi-continuous operation type, and Continuing the three operating types, what is the knowledge about different types of emulsified asphalt equipment?

Modified (rubber powder) bitumen equipment, one of the road maintenance equipment. It is a kind of equipment that measures, mixes and develops SBS, rubber powder and asphalt.
Modified (rubber powder) bitumen equipment is a set of wet modification processing technology, which mainly consists of modified material metering and promotion, bitumen rapid heating, asphalt metering, high-intensity mixing tank, mixed material transfer pump, development tank, colloid mill, Control system and other components.

Synchronized gravel sealing is a process technology for treating cracks in asphalt pavement, and it is currently a road construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical features are? If you don’t know, just follow the editor of Sinoroader and take a look.

Preventive pavement maintenance is a periodic mandatory maintenance measure, which is taken to restore the pavement surface service function when the pavement structure strength is sufficient and only the surface function is attenuated. New preventive maintenance technologies such as super-viscous fiber-added low-noise micro-surfacing and synchronous gravel seal have been widely used on the main lines of national highways, and the construction effect has been widely praised by customers.
Super-viscous fiber-added low-noise micro-surfacing starts with the gradation of micro-surfacing and the main material modified emulsified asphalt. By reducing the structural depth of the micro-surfacing and changing the distribution state of the coarse and fine materials on the surface of the micro-surfacing, the driving noise is reduced, while ensuring its anti-skid performance, effectively improving its adhesion, waterproofness, durability and crack resistance, and can solve the defects of easy detachment, excessive noise and reflective cracks of ordinary micro-surfacing.

The slurry seal truck is one of the main maintenance methods of highways. The slurry seal is made of emulsified asphalt as the binding material, well-graded mineral materials, fillers, water and additives, etc., mixed in a certain proportion. The slurry mixture is evenly spread on the old road surface to be treated with a sealing truck, and is firmly combined with the original road surface to form a new thin layer of asphalt mixture. So what preparations need to be done before construction? Let’s find out below.

What details should be paid attention to when adding materials to the emulsified bitumen equipment? Speaking of emulsified bitumen equipment, I don’t know how much you know? What should we pay attention to when adding materials?
The black anti-static tweezers grinding wheel of the emulsified bitumen equipment has no heating barrel. Before use, you must first add an appropriate amount of diesel, let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is about 80 to 100 degrees) Open the shut-off valve on the oil pipe and discharge the diesel in the machine. The temperature of the black anti-static tweezers grinding wheel is about 80 to 100 degrees before it can be loaded and put into production. If there is a heating collet, heat the grinding wheel before starting, and then load the materials for production.

Friends who are ready to get started have a surprise today. The editor will give you a brief introduction on how to produce emulsified asphalt.

There is a wide variety of asphalt melting equipment on the market, including different brands and models. The prices of these devices vary widely, depending mainly on factors such as their features, performance, and specifications.
Asphalt melter equipment produced by some large brands such as Sinoroader usually has higher quality and reliability, so the price is relatively higher. However, they also offer longer service life and better maintenance support.

Asphalt mixture is a kind of composite material, mainly composed of asphalt, coarse aggregate, fine aggregate, mineral powder, some also added polymer and wood cellulose; By these different quality and quantity of materials mixed to form different structures, and have different mechanical properties

Asphalt spreading trucks are used to spread the permeable oil layer, waterproof layer and bonding layer of the bottom layer of asphalt pavement on high-grade highways. It can also be used in the construction of county and township-level highway asphalt roads that implement layered paving technology. It consists of a car chassis, an asphalt tank, an asphalt pumping and spraying system, a thermal oil heating system, a hydraulic system, a combustion system, a control system, a pneumatic system, and an operating platform.

The viscosity of the bitimen melter equipment decreases as the temperature increases during the production process. Its output viscosity is about twice as high as every 12°C increase. During production, the base bitimen melter equipment must first be heated to a liquid state and then emulsified. In order to better integrate the emulsification ability of colloid milling, the viscosity of base bitimen melter is generally controlled to be about 200 cst. The lower the temperature, the higher the viscosity, which increases the pressure on the bitimen melter pump and colloid milling, making emulsification impossible: However, on the other hand, in order to prevent the asphalt debarrel equipment from weaning when the moisture of th

During the use of emulsified bitumen equipments, if maintenance is not paid attention to, the cycle will be short, and problems will often occur during use. Only by doing a good job of maintenance can the operation efficiency of the equipment be improved. For example, during maintenance, the following points must be grasped.
It is necessary to regularly check the wear condition of the internal structural components of the mechanical equipment, such as the core feed pipe, the rough jaw plate on the impeller, the cone cap, the wear level of the jaw plate, the rain shield on the circle, and the wear condition. If the wear is more serious, it is necessary to replace or repair it in time. When replacing, it is also necessary to pay attention to the model and specifications, and replace it according to the original components as a reference.

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.
For the block asphalt melting equipment, the Provincial Environmental Protection Department will review the application materials, and appoint the Provincial Block Asphalt Melting Equipment Management Office to organize relevant doctors to conduct technical evaluation and on-site technical evaluation, and produce expert technical evaluation opinions and on-site inspection reports. Then report the materials of the block asphalt melting equipment to the meeting of directors for scientific research and make a review decision.

The asphalt spreading truck is an intelligent high-tech product that specializes in spreading emulsified asphalt, diluted asphalt, hot asphalt, heavy traffic asphalt and modified asphalt. It is used in highway construction and highway maintenance projects, and can be used for the construction of upper and lower seals, permeable layers, waterproof layers, bonding layers, asphalt surface treatment, asphalt penetration pavements, fog seals and other projects of different grades of highway pavements. , can also be used for the transportation of liquid asphalt or other heavy oil. So what are the advantages of Qiangguomeng’s asphalt spreader trucks?

Road repair Keep the road to maintain the performance of the road, restore the damaged part in time, ensure the safety, comfort and smooth driving, save transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time. With the performance, the damaged part is restored in time to ensure the safety, comfort and smooth driving, saving transportation costs and time; Correct technical measures should be taken to improve the quality of the project, extend the service life of the road, and postpone the reconstruction time.