What are the benefits of using a complete set of asphalt mixing equipment?

The asphalt mixing equipment mentioned here may also refer to an asphalt concrete mixing plant. At present, asphalt mixing equipment generally uses a complete set of equipment for mixing. So what are the benefits of using a complete set of equipment?
1. More effective.
In today’s industrial production, a complete set of asphalt mixing equipment can help improve production efficiency and ensure product quality. This is why even in a mixing plant, the equipment used is a complete set of equipment.
2. Ensure quality.
When mixing asphalt, a certain ratio is set. For this type of asphalt liquid used in different occasions, its ratio control has strict requirements. It is necessary to determine its mixing method and mixing time to ensure that the asphalt liquid is consistent with the production site. One of the advantages of a mixing plant is that the quality can be effectively controlled.
3. It can be sampled.
After mixing at the mixing plant, the quality inspector can sample and inspect to ensure that the mixed asphalt liquid meets the use requirements.
In short, asphalt mixing equipment will use a complete set of equipment, mainly to facilitate the later asphalt to meet production needs. Through the mixing plant, the mixing time and feeding sequence can be better controlled, so that the mixed product can meet different use requirements. And after using the archiving equipment, effective spot checks can be carried out, which can better ensure that the quality meets the construction requirements.

When we operate the asphalt mixing station, we should heat the equipment half an hour in advance, and the clear tank should be heated for at least two hours; and manually operate each part of the equipment to ensure that it is in good operation. status; it is also necessary to conduct relevant inspections on the valves and manually collect and return oil to ensure that the equipment can operate normally.
Several requirements for safe operation of asphalt mixing plants:

Safety is the key point for any piece of equipment, and asphalt mixers are of course no exception. What I want to share with you is the knowledge in this area, that is, the safe operation specifications of asphalt mixers. You might as well pay attention to it.
In order to prevent the asphalt mixer from moving during work, the equipment should be placed in a flat position as much as possible, and at the same time, use square wood to pad the front and rear axles so that the tires are elevated. At the same time, the asphalt mixer must be provided with secondary leakage protection, and it can only be started after the inspection, trial operation and other aspects are qualified.

The quality of asphalt mixture directly determines the quality of asphalt pavement engineering. This article discusses the key points of supervision of ordinary highway asphalt plants in order to better monitor the quality of asphalt mixture.

In recent years, asphalt concrete, as a new green building material, is gradually being valued by people because of its excellent performance in saving resources, being environmentally friendly, ensuring the quality of construction projects, and achieving sustainable utilization of resources. The development of asphalt concrete fully embodies my country’s policies to achieve energy conservation and emission reduction, and is also an important measure to promote the development of circular economy.

Asphalt mixing plant is a complete set of equipment composed of many systems. It is widely used in the current society. Its components include batching system, drying system, combustion system, hot material lifting, weighing and mixing system and control system.
In the process of asphalt mixing, heating is an indispensable link, because there must be a system for heating in the asphalt mixing station, but the system generally fails for various reasons. So how should the heating system of the asphalt mixing station be improved? This article will briefly explain this issue.
Generally speaking, when the asphalt mixing station is running under low temperature conditions, the asphalt circulation pump and spray pump cannot operate normally, which will cause the asphalt in the asphalt scale to solidify, and then the asphalt mixing station cannot be produced. Therefore, the asphalt mixing station needs a heating system during operation.

Asphalt (composition: asphaltenes and resin) tanks are divided into: intermittent and continuous functions according to the production process: initial batching of aggregates, heating and drying, screening and measurement; heating and insulation of asphalt (composition: asphaltene and resin) , transportation and measurement; transportation and measurement of filler; uniformly mix the measured aggregate, asphalt (composition: asphaltene and resin), and filler into a finished product of a certain temperature.

Judging from the situation of highways in our country, asphalt pavement is the most used, which is one of the reasons why asphalt mixing plants have developed so rapidly. Under the situation of rapid economic development, the quality problems of asphalt pavement are gradually increasing, which puts forward higher and higher requirements for the quality of asphalt. It is understood that the primary factor that affects the quality of asphalt is the ratio of raw materials. This is also covered in the introduction of asphalt mixing stations. You can discuss it together.
In order to obtain high-quality asphalt products, in addition to the asphalt mixing equipment meeting the requirements, selecting the appropriate asphalt mixture gradation type is also a top priority. According to my country’s current regulations, the maximum particle size of the asphalt mixture in the upper layer of the highway should not exceed half of the layer thickness; while the maximum particle size of the aggregate in the middle surface layer of asphalt mixture should not exceed two-thirds of the layer thickness; and the asphalt layer should not exceed half of the layer thickness. The maximum nominal aggregate size of the pavement structural layer mixture should not exceed one-third of the layer thickness.
Based on this analysis, if an asphalt surface layer with a certain thickness is selected according to the above specifications, the particle size of the asphalt mixture aggregates will generally be larger, which will inevitably bring insurmountable construction difficulties to the construction of asphalt concrete pavement. After investigation, testing, analysis, and comparison, it can be seen that the lower layer has a wider choice, so the AG-201 gradation type can be used; while the selection of the upper layer mixture type is more difficult, and it is necessary to achieve a reasonable choice of this mix ratio. , on the one hand, we must examine as many aggregate resources as possible, and on the other hand, we must also consider the model of the mixing equipment.
In order to ensure the quality of the project, strict selection and inspection of engineering materials must be carried out. Therefore, the selection and determination of raw materials should be based on the requirements for pavement structure and use quality, combined with the supply of floor materials, and inspection in accordance with the requirements of relevant test procedures, and then Select the best materials so that all technical indicators of the materials meet the specified technical requirements.

Asphalt mixing plant refers to a complete set of equipment used for batch production of asphalt concrete. Its main function is to produce asphalt mixture, colored asphalt mixture, etc., and has been widely used in road construction. However, during the production process of asphalt mixture, pollutants such as noise, dust, and asphalt smoke will be produced, seriously polluting the environment and threatening the health of workers. Therefore, under the current background of building a resource-saving and environment-friendly society in our country, it is very important to save energy and reduce consumption during the use of asphalt mixing plants. The following article mainly starts from the three factors that affect the asphalt mixing plant, and explores the energy saving and consumption reduction measures of the asphalt mixing plant, aiming to reduce the cost of asphalt production and improve the efficiency of the asphalt plant.

Asphalt mixing plants are highly professional equipment with complex systems. It is inevitable that some failures will occur during use. So, what are the common hardware failures of asphalt mixing plants? Do you know?
(I) Because its system is relatively complex, when different components have problems, the problems caused may be different. If during the operation, it is found that the material addition of each silo is inaccurate, this problem may be due to the failure of the sensor of the asphalt mixing plant. At this time, the machine should be stopped for inspection and replaced with a new sensor if necessary. It may also be caused by the jamming of the scale bar. At this time, foreign objects should be removed in time.

Modified Bitumen

Asphalt mixing equipment is a large-scale equipment, so you must pay attention to safety when using it to avoid accidents. But to put it simply, if you want to truly use it safely, you must master some basic common sense. The following main things must be kept in mind.

Main uses of asphalt mixing plant
Asphalt mixing plant, also called asphalt concrete mixing plant, can produce asphalt mixture, modified asphalt mixture, and colorful asphalt mixture, fully meeting the needs of constructing expressways, graded highways, municipal roads, airports, ports, etc.
The overall composition of asphalt mixing plant
Asphalt mixing equipment mainly consists of batching system, drying system, incineration system, hot material improvement, vibrating screen, hot material storage bin, weighing mixing system, asphalt supply system, powder supply system, dust removal system, product silo and control system, etc. Some composition.

Bitumen, a black or brown petroleum-like material, has a viscosity ranging from a viscous liquid to a glassy solid. It can be obtained as a residue separated from natural deposits. Bitumen consists of hydrogen and carbon compounds with small amounts of nitrogen, sulfur and oxygen. The preparation of mixed materials for mixing with asphalt is done in several steps:
Prediction: According to the asphalt recipe, the individual components of the aggregate are weighed. Usually this is done using a belt scale, since the material must go to the next step in a continuous flow.

There is also a reversing valve in the asphalt mixer, which generally does not cause problems, so I have not understood its solution in detail before. But in actual use, we encountered this kind of failure. How should we deal with it?

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixer plant also needs to be powered on for trial operation before it is officially put into work.
At the beginning of the test run, first run a single motor, and at the same time check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

The asphalt mixing plant is constructed according to a certain process, which can not only ensure the construction quality, but also ensure that the asphalt mixing plant is not damaged. Although the construction details are critical, the key skills of the asphalt mixing plant construction must be mastered.
Before the construction of the asphalt mixing plant, the top surface of the asphalt mixing plant construction range should be removed, and the dry and flat site elevation should be kept to meet the design requirements. If the ground surface is too soft, the foundation should be reinforced to prevent the construction machinery from becoming unstable and to ensure that the pile frame is vertical.

Any kind of mechanical equipment must go through precise design, testing and other processes before it can be manufactured, and the same is true for asphalt mixing stations. According to the survey, the following stages are necessary for any asphalt mixing plant.
First of all, the main technical parameters of the product to be designed must be determined according to market needs, so construction market research, data analysis and other links are indispensable. Secondly, the ideal working principle and the plan to realize this principle will be determined through innovative conception and optimization screening. , a schematic diagram of the overall design scheme should also be given.

Asphalt mixing plants are large-scale products with high professional and technical requirements, and are composed of multiple systems. Among them, asphalt tanks are also a very critical part. Whether it is manufacturing, debugging or installation, it needs to be operated according to the actual application needs of users.
In addition to the manufacturing, debugging and installation, which need to be operated by installers, the maintenance of asphalt tanks in asphalt mixing plants must also be managed by professionals. At the same time, they must strictly follow all safety rules to operate. Before operation, they must be proficient in the relevant requirements and based on the regulations and safety instructions for storing and handling hot asphalt.

Asphalt concrete mixing equipment generally uses conveyor belt conveyors to transport cold materials. Its main advantages are large conveying capacity, continuous operation, simple equipment structure and automatic control. However, belt deviation is a common fault, which directly affects the drying operation of the drying drum and also affects the production efficiency of the mixing equipment. Therefore, it is very important for the asphalt mixing station to solve the belt deviation problem at the operation site of the asphalt concrete mixing equipment.

We know that the first priority in production is to ensure safety. In the process of operating equipment, staff must always pay attention to using the correct operating methods. Regarding the asphalt mixing plant, it is used to produce asphalt mixtures, modified asphalt mixtures, and colored asphalt mixtures to meet the needs of highways, graded highways, municipal roads, airports, etc.

When inspecting the asphalt mixing plant, it was found that the asphalt in the pipeline solidified because the temperature of the asphalt transportation pipeline did not meet the requirements. Analysis believes that the reasons for this result are that the high-level oil tank of the heat transfer oil is too low, resulting in poor circulation of the heat transfer oil; the second is that the inner tube of the double-layer pipe is eccentric; the third is that the heat transfer oil pipeline is too long; and the fourth is that the heat transfer oil pipeline is not insulated measure.

The mobile forced asphalt mixing equipment adopts intermittent drying cylinder, double forced mixer, the main machine can be towed, small footprint, short installation cycle, convenient operation and maintenance, good stability, high degree of automation, high degree of standardization, and high quality of finished products, and the technology of continuous improvement. The mobile forced asphalt mixing plant is suitable for high-grade road asphalt paving and maintenance.
1. The combined structure of the drum dryer and the batching machine is installed on a movable bracket for easy movement.
2. The asphalt mixing plant is equipped with a double horizontal shaft to boil the aggregate and ensure uniform mixing.
3. In the densely arranged hanging barrels, the hot aggregate rises vertically. This lifting tool is easy to use and reliable.
4. For accurate weighing of aggregates, asphalt and powder ore, a measuring scale is used, which contains a weighing sensor for electronic measurement.
5. The movement of the power material follows a closed spiral path, which ensures little material loss and provides safe transfer.
6. On the cyclone burner, high-pressure oil is sprayed out and quickly atomized. In the combustion chamber, the material is fed in a spiral manner and automatically ignited by the oil mist, which ensures combustion efficiency. The cylindrical barrel of the burner is separated from the burner head. The furnace cavity can be pushed in and pulled out, which is convenient for replacing the damaged side column bricks inside the burner. The entire burner has a large heat capacity and high thermal strength. This is cost-effectiveness.

The basic working principle of the green asphalt mixing plants can be roughly summarized in the following ways:
To put it simply, an asphalt plant is actually a set of equipment that can mix several materials according to a predetermined ratio to form a relatively uniform mixture. It is currently widely used and is very important for the construction of different projects. Its performance Various aspects also have a great impact on the engineering quality of asphalt pavement.
Asphalt mixing plant equipment is usually divided into two structures. The intermittent type is relatively more complex in structure and process. The aggregates need to be screened twice and then measured in batches. The batching accuracy is higher. , the mixing quality is good and can meet different construction requirements. The continuous type has a slightly lower accuracy due to its simple structure and simplified operating procedures.

At present, the production efficiency of asphalt mixing plants in my country’s asphalt construction is far lower than the theoretical efficiency at the time of design. The low efficiency of organic waste gas treatment will not only delay the construction process and cause a waste of resources, but also the quality of the construction will not be very good. guarantee. In the construction of asphalt pavement, the main reasons for the low production efficiency of the asphalt plant are insufficient supply of mixture, resulting in loss of continuity of construction, improper equipment parameter settings, excessive overflow and other problems. Effective measures must be taken to deal with these problems, and ultimately improve production efficiency and ensure construction quality.

There is also a reversing valve in the asphalt mixing plant, which generally does not cause problems, so I have not understood its solutions in detail before. But in actual use, we encountered this kind of failure. How should we deal with it?
The failure of the reversing valve of the asphalt mixing station is not complicated, that is, the reversing is not timely, gas leakage, electromagnetic pilot valve failure, etc. The corresponding causes and solutions are of course different. For the reversing valve to not change direction in time, it is generally caused by poor lubrication, the spring is stuck or damaged, oil dirt or impurities get stuck in the sliding part, etc. For this, it is necessary to check the status of the lubricator and the quality of the lubricating oil. Viscosity, if necessary, the lubricant or other parts can be replaced.
After long-term use, the reversing valve is prone to wear of the valve core sealing ring, damage to the valve stem and valve seat, resulting in gas leakage in the valve. At this time, the sealing ring, valve stem and valve seat should be replaced, or the reversing valve should be replaced directly. In order to reduce the failure rate of asphalt mixers, maintenance must be strengthened on a daily basis.

Asphalt mixing equipment has a special function, which is that it can perform cyclic heating to make the asphalt product reach the best condition. But how does it achieve this function? Everyone is curious about this.

Certain failures cannot be avoided during the use of the asphalt mixing plant. For example, a malfunction of the cold material feeding device may cause the asphalt mixing plant to shut down. This may be due to a malfunction in the asphalt mixing plant or due to gravel or foreign matter being trapped under the cold material belt. If it is stuck, if it is a circuit failure, first check whether the motor control inverter of the asphalt mixing station is faulty and whether the line is connected or open.

What should I do when the reversing valve in the asphalt mixing plant fails? The editor has a trick:
1. The reversing valve cannot be reversed or the reversing action is slow, which is generally caused by poor lubrication, stuck or damaged springs, oil or impurities stuck in the sliding parts. In this regard, you should first check whether the oil mist is working normally; whether the viscosity of the lubricating oil is appropriate. If necessary, the lubricating oil should be replaced, the sliding part of the reversing valve should be cleaned, or the spring and reversing valve should be replaced.