What are the differences between the modification processes of emulsified asphalt equipment?

Classification analysis of emulsion bitumen equipment is used to heat-melt bitumen. According to the actual cutting effect of mechanical equipment, it is loosened into a solution with demulsifier in the form of tiny droplets to form oil-in-water asphalt. Industrial equipment for lotions. Emulsion bitumen equipment can be divided into three types: portable, transportable and mobile according to the equipment, layout and maneuverability of the equipment.

When using asphalt melting equipment, you need to pay attention to the following points:
1. The power must be cut off during installation and operation to ensure safety.
2. Before starting operation, check whether all components are normal and have no fault prompts. In particular, the inspection of key parts such as the heater part and the conveyor belt device is particularly important.

Sinoroader emulsifier does not need to add acid or adjust pH value in the production of emulsified asphalt, thus reducing the process, reducing equipment maintenance, saving labor and materials. It reduces the cost of emulsified asphalt, produces acid-free, eliminates equipment corrosion emulsion, does not consider anti-corrosion measures in the selection of equipment, and greatly reduces the capital investment of equipment.
Main technical indicators:
Active ingredient content 40±2%
pH value 8-7
Appearance: yellow or dark yellow liquid
Odor: non-toxic, aromatic gas
Solubility: soluble in water and some organic solvents
Temperature ratio:
Water temperature: 70℃-80℃
Asphalt temperature: 140℃-150℃
Emulsifier: 8%-10%
Asphalt ratio: water = 4:6
Precautions:
The temperature of the emulsifier aqueous solution should not exceed 70%
When the temperature is low, the product is in a paste or paste, and the heating is variable.
Different varieties of asphalt should adjust the amount of emulsifier, and the use test should be derived from the test.

Emulsified asphalt is made by hot melting asphalt, dispersing it in an aqueous solution containing an emulsifier in a fine particle state through mechanical action, forming an oil-in-water asphalt emulsion. In road construction and maintenance projects, emulsified asphalt can be used for road maintenance, bonding between road layers, bridge deck paving, permeable oil on cement-stabilized macadam foundation, slurry seal waterproof layer, etc. It has the advantages of cold construction, safety, environmental protection, resource conservation, energy conservation, extended construction season, and improved construction conditions. It plays a very important role in the construction and maintenance of municipal roads, especially in recent years, the improvement of the production level of emulsified asphalt has actively promoted the technological progress and promotion and application of emulsified asphalt. However, in the production and use of emulsified asphalt, undesirable phenomena such as crusting, flocculation, oil-water stratification, and agglomeration often occur, which brings unnecessary troubles to construction. To this end, the author conducted a large number of experimental studies from nine aspects, including emulsification equipment, emulsifier, base asphalt, pH value, temperature, storage temperature, mechanical action, freezing and melting, and long-term placement, and summarized the factors that affect the stability of emulsified asphalt. The analysis is as follows:

What details should be paid attention to when adding materials to the emulsified bitumen equipment? Speaking of emulsified bitumen equipment, I don’t know how much you know? What should we pay attention to when adding materials?
The black anti-static tweezers grinding wheel of the emulsified bitumen equipment has no heating barrel. Before use, you must first add an appropriate amount of diesel, let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is about 80 to 100 degrees) Open the shut-off valve on the oil pipe and discharge the diesel in the machine. The temperature of the black anti-static tweezers grinding wheel is about 80 to 100 degrees before it can be loaded and put into production. If there is a heating collet, heat the grinding wheel before starting, and then load the materials for production.

The selection of asphalt melting equipment should take into account factors such as the use environment, working conditions, and technical requirements. Common ones include hot oil heating equipment, electric heating equipment, and gas heating equipment.
Hot oil heating equipment is suitable for occasions that require long-term heating and high temperature control accuracy;
Electric heating equipment is suitable for small projects or occasions where temperature control accuracy is not required;
Gas heating equipment has the advantages of simple operation and low cost, but safety protection measures must be strictly followed.
When choosing, it is also necessary to comprehensively consider factors such as economy and environmental protection.

Asphalt spreading trucks are used to spread the permeable oil layer, waterproof layer and bonding layer of the bottom layer of asphalt pavement on high-grade highways. It can also be used in the construction of county and township-level highway asphalt roads that implement layered paving technology. It consists of a car chassis, an asphalt tank, an asphalt pumping and spraying system, a thermal oil heating system, a hydraulic system, a combustion system, a control system, a pneumatic system, and an operating platform.

Modified asphalt equipment is a widely used asphalt equipment. Now its ultra-high performance has been widely praised by users. However, we must first use the modified asphalt equipment safely to fully demonstrate its performance. So how much do you know about the safe use and operation of modified asphalt equipment? Today, Sinoroader will explain it in detail:
1. Placement: The modified asphalt equipment should be placed on a flat place, and the front axle wheel should be fixed with sleepers and the tires should be dangling to ensure that the machine does not move around during operation.
2. Check regularly whether the mixer blades are deformed and whether the screws are loose.
3. Check whether the running direction of the mixing barrel is consistent with the arrow. If not, please replace the positive and negative poles of the wiring.
4. Before powering on, check for empty vehicle trial operation, check for leakage, and check the idling of the mixing barrel. The normal speed is about 3 times faster when the empty vehicle is full. If the speed is wrong, stop the car for verification.
5. If the asphalt material is stopped for one hour after mixing, clean the mixing barrel, pour in clean water, and clean the mortar. Then drain the water, remember that there must be no water in the bucket to prevent the formula from changing, and even rust on the pages and other links. During use, everyone should pay attention to some small links to avoid unnecessary losses in their work.

Colored asphalt pavement is a kind of special pavement material that mixes colored particles into asphalt and then lays on the pavement

After the emulsified asphalt equipment has been used for a long time, it needs maintenance. There are several points to note when adjusting the emulsified asphalt equipment:
1. During use, regular maintenance should be carried out as appropriate according to the processing materials;
2. For the maintenance and use of the motor, please refer to the motor instruction manual;
3. Most of the random spare parts are national standard and department standard parts, which are purchased all over the country;
4. The colloid mill is a high-precision machine with a line speed of up to 20m/second and a very small grinding disc gap. After overhaul, the coaxiality error between the housing and the main shaft must be corrected with a dial indicator to ≤0.05mm;
5. When repairing the machine, it is not allowed to be directly knocked with an iron bell during the disassembly, reassembly and adjustment process. Use a wooden hammer or a wooden block to knock gently to avoid damaging the parts;
6. The seals of this machine are divided into static and dynamic seals. The static seal uses an O-type rubber ring and the dynamic seal uses a hard mechanical combined seal. If the hard sealing surface is scratched, it should be repaired by grinding on flat glass or flat castings immediately. The grinding material should be ≥200# silicon carbide grinding paste. If the seal is damaged or cracked seriously, please replace it immediately.

The hydraulic bitumen decanter equipment produced by our company uses thermal oil as the heat carrier and has its own burner for heating. The thermal oil heats, melts, debarks and dehydrates the asphalt through the heating coil. This device can ensure that the asphalt does not age, and has the advantages of high thermal efficiency, fast barrel loading/unloading speed, improved labor intensity, and reduced environmental pollution.

Modified bitumen equipment uses modified bitumen colloid mill. Its blade has high hardness, high linear speed of the moving disk, and the gap can be adjusted to 0.15mm. It is suitable for processing various polymer-modified bitumens, such as SBS, PE, EVA, etc.

As we all know, emulsified bitumen is a single-component black viscous liquid that can combine the roadbed and the pavement to improve the performance and service life of the road. So what problems should be paid attention to when using emulsified bitumen? Let’s follow the editor of Sinoroader Group, an emulsified bitumen manufacturer, to learn about it.

As a manufacturer with many years of experience in emulsified bitumen construction, Sinoroader Group believes that everyone needs to pay attention to the following 2 points when using it:

Improve the reliability of SBS bitumen emulsion plants: Once you have an established maintenance, it will help to identify problems. This will allow the maintenance plan and time to be carried out at your convenience. Regular maintenance will increase the normal operation time of SBS bitumen emulsification equipment, and it can be used when necessary. Low cost of operation: Imagine an SBS bitumen emulsification plant breaks down during a project. With a protective maintenance plan, such things happen less often because you have taken good care of the SBS bitumen emulsification plant.
If the SBS bitumen emulsification plant wants to maintain normal operation, then in the production process. All stages need to be maintained normal, among which the normality of the circuit system is an important aspect to ensure its smooth operation. Imagine that if there is a problem with the circuit during the on-site operation, it may affect the development of the entire project.
For users, of course, they don’t expect this to happen, so if the SBS bitumen emulsification plant is in the work of using the SBS bitumen emulsification equipment, if there is a circuit problem, it is necessary to take appropriate measures to solve it in time. The following article will give a detailed description of this problem, and the following SBS bitumen emulsification plant can be of benefit to everyone.

Modified asphalt equipment is a widely used asphalt equipment. Now its ultra-high performance has been widely praised by users. However, we must first ensure the safe use of modified asphalt equipment in order to fully demonstrate its performance. So how much do you know about the safe use and operation of modified asphalt equipment? Today, Gaoyuan Road Construction will explain it in detail:
1. Placement: The modified asphalt equipment should be placed on a flat place, and the front axle wheel should be fixed with sleepers and the tires should be suspended to ensure that the machine does not move around during operation.
2. Check regularly whether the mixer blades are deformed and whether the screws are loose.
3. Check whether the running direction of the mixing barrel is consistent with the arrow. If not, please replace the positive and negative poles of the wiring.
4. Before powering on, check for empty vehicle trial operation, check for leakage, and check the idling of the mixing barrel. The normal speed is about 3 times faster when the empty vehicle is full. If the speed is wrong, you should stop and check.
5. If the machine is stopped for more than one hour after the asphalt mixing is completed, clean the mixing barrel, pour in clean water, and clean the mortar. Then drain the water. Remember that there should be no water accumulation in the barrel to prevent the formula from changing and even rusting of the pages and other links.

Each F1 track must be paved with three layers of asphalt, middle and lower, of which the lowest layer is 10 cm coarse asphalt concrete bearing layer, its flatness is less than 8 mm; In the middle is a 4 cm medium grained asphalt concrete bond layer, its flatness is less than 5 mm; The top layer uses 4 cm modified asphalt mixture as the surface wear layer, and the flatness is less than 2 mm.

The paved F1 track cannot have more than 3 points per kilometer of flatness detection, which is much higher than the highway.

Preparation items for micro-surfacing slurry sealing: materials, construction machinery (micro-surfacing paver) and other auxiliary equipment.
The micro-surface slurry seal requires emulsified asphalt and stone that meet the standards. The metering system of the micro-surfacing paver needs to be calibrated before construction. The production of emulsified asphalt requires asphalt heating tanks, emulsified asphalt production equipment (capable of producing asphalt content greater than or equal to 60%), and emulsified asphalt finished product tanks. In terms of stone, mineral screening machines, loaders, forklifts, etc. are needed to screen out oversized stones.
The tests required include emulsification test, screening test, mixing test and the equipment and technical personnel required to do these tests.

Working conditions of asphalt debarreling equipment:
(1) Outdoor temperature: 20°C (average temperature of day and night)
(2) Heat exchange oil: 320 ℃
(3) Loading time is not included (because the personnel equipped in each unit are different, so the loading time is also different)
(4) There is no fluctuation in oil temperature (optimal automatic burner)
(5) The working temperature of the oil furnace is 220-260 ℃
(6) The flow rate of the oil circulation pump is not less than 50m3/h traffic
(7) When the outdoor temperature is lower than 20℃, the output decreases. The lower the temperature, the lower the output, and the higher the temperature, the higher the output.
(8) The greater the deformation of the asphalt barrel, the greater the impact on the output

Microsurfacing is a thin layer of overlay placed on old asphalt pavement and is a type of preventive maintenance process. The purpose of microsurfacing is road maintenance. After micro-surface paving, it can repair cracks in the original road surface, waterproof and beautify the road surface.
The construction method of micro surfacing is: using a micro surfacing paver to evenly spread modified emulsified asphalt, a certain grade of mineral materials, water and other additives on the road surface in a certain proportion.

Conventional pit repair techniques are mainly hot material repair and cold filling repair, and warm mixing technology is used to ensure compaction, while there are also some special repair methods such as slurry seal/micro-surface material repair

In the asphalt-water system, the emulsifier molecules move between the asphalt and water interface, and the water-loving groups of the molecules are adsorbed on the surface of the asphalt, making it charged, while the hydrophilic groups enter the water phase. This connects the asphalt particles with water, reducing the interfacial tension between the two. At the same time, because the asphalt particles have the same charge and repel each other, they are prevented from agglomerating with each other, so that the asphalt emulsion can remain uniform and stable for a certain period of time. The nature of the charge is determined by the charge of the hydrophobic group or hydrocarbon chain of the emulsifier. If it is negatively charged, the asphalt particles are negatively charged, and the emulsion formed is an anionic asphalt emulsion. Otherwise, it is a cationic asphalt emulsion. If the asphalt particles have both negative and positive charges, the emulsion is a zwitterionic asphalt emulsion; in addition, there is also a non-ionic asphalt liquid.

Changing the color of asphalt pavement is an important project aimed at improving the beauty of roads, optimizing traffic signs and enhancing urban landscape effects. The following is a detailed introduction to the color change of asphalt pavement:
1. Color change method
Using pavement color change spray:
Spray directly on the original asphalt pavement surface to make the road surface look brand new.
This method is simple and fast to construct, with bright and lasting colors, and will not change the structure of the pavement.

According to the configuration, layout and controllability of bitumen melting equipment, bitumen melting plant can be divided into three types: mobile, transportable and portable. What should be paid attention to in the production of bitumen melter equipment of different sizes? Let’s learn about it below!
Bitumen melting plant is to fix the demulsifier mixing equipment, black anti-static tweezers, asphalt pump, automatic control system, etc. on a special support chassis. Because the bitumen melter equipment can directly change the production site, it is suitable for the production of emulsion bitumen in construction sites with decentralized projects, small usage and frequent movement.
The main components of the bitumen melting equipments are installed in one or two 60 standard containers. The bitumen melting plant is loaded and transported separately to complete the relocation of the construction site. With the help of asphalt melting equipments hoisting equipment, it is quickly installed and put into operation. Such bitumen melter plant has large, medium and small different configurations, which can meet different project requirements.

Some of the equipment of emulsified modified bitumen equipment are as follows. The specially made bitumen filter can effectively filter the residues and dirt in the high-temperature culture medium bitumen to avoid damage to the subsequent equipment. The emulsified modified bitumen equipment adopts a spiral plate type or a shell and tube heat exchanger to quickly heat the culture medium bitumen through high-temperature heat transfer oil to meet the needs of the production process. The emulsified modified bitumen equipment is heated in the storage tank to prevent the bitumen from aging due to long-term high-temperature heating and exposure to the air. The sulfate generated during the production process of the emulsified modified bitumen equipment is very limited, reducing air pollution.
The emulsified modified bitumen equipment sends the modified material manually poured into the dumping bin to the bitumen batching tank by wind or spiral. It can be equipped with a metering and calibration system. The emulsified modified bitumen equipment thickener is automatically or manually added. The emulsified modified bitumen equipment can be equipped with a metering and calibration system. Emulsified modified bitumen equipment transportation and metering and calibration system, the emulsified modified bitumen equipment adds the set bitumen amount to the batching tank through the frequency converter and computer interlock. The emulsified modified bitumen equipment and bitumen steam flowmeter use big brand products to ensure the preparation.

Synchronized gravel sealing is a process technology for treating cracks in asphalt pavement, and it is currently a road construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical features are? If you don’t know, just follow the editor of Sinoroader and take a look.

For the relevant knowledge of modified asphalt equipment, we have more or less introduced it in the above articles. I believe that most users also have some simple understanding of it. Today we also mastered:
In order to meet the different requirements of customers, the configuration and process of the equipment produced by the manufacturers of modified asphalt equipment are diversified. There are fixed production types, mobile types, and imported main machines, but the imported main machines are expensive, so most customers configure domestic pipeline emulsifiers or colloid mills. In terms of the degree of automation, there are fully automatic production and semi-automatic production. Regardless of the form of production, each has its own advantages and disadvantages. What kind of process and configuration is used depends on the annual production volume and the customer’s requirements for equipment, product performance requirements and other factors. I hope that these introductions can help users choose to a certain extent.

Precautions during the production of emulsified bitumen equipment. How much do you know about this information? Let’s learn more about it:
When the emulsified bitumen equipment is in production, the viscosity of the bitumen decreases with the increase of temperature. For every 12℃ increase, its dynamic viscosity decreases by about one time. During production, the base bitumen should be heated to liquid state before emulsification. In addition, in order to adapt to the emulsification capacity of the colloid mill, the base bitumen dynamic viscosity is generally controlled to be about 200cst. The lower the temperature, the higher the viscosity, which increases the burden on the bitumen pump and the colloid mill, making it difficult to emulsify; but on the other hand, in order to prevent the demulsification caused by excessive vaporization and evaporation of water in the finished product during the production of emulsified bitumen, it is impossible to heat the base bitumen temperature too high. Generally, the finished product temperature at the outlet of the colloid mill should be controlled to be less than 85℃.

Is the performance of Sinoroader’s fully automatic emulsified asphalt production equipment stable and unstable? To be honest, whether the performance of a product is stable or not can only be known through practice, right?
Chairman Mao, the great leader of China, once said, “Without practice, there is no right to speak.” Yes, people who have never used it naturally have no right to speak. Now the editor will talk about the fully automatic emulsified asphalt production equipment that I am using!

The heating principle of asphalt decanter equipment is to heat, melt and decanter the asphalt through the heating plate. It is mainly composed of de-barreling box, lifting system, propeller and electrical control system.
The box of asphalt decanter plant is divided into upper and lower chambers. The upper chamber is the asphalt melting chamber, which is densely covered with heat transfer oil heating coils or hot air heating pipes. The asphalt is melted and removed from the barrel by heat. The hoisting hook is installed on the gantry, and a barrel grabber is hung. The asphalt barrel is lifted by the electric winch, and then the asphalt barrel is placed on the guide rail by horizontal movement. Then the propeller pushes the barrel into the upper chamber through two guide rails, and an empty barrel is pushed out at the rear end outlet.
An anti-drip oil tank is provided at the entrance of the asphalt barrel. The asphalt enters the lower chamber of the box and is continuously heated to a temperature of about 100 to be transported, and then pumped into the asphalt tank by the asphalt pump. The lower chamber can also be used as an asphalt heating tank.
The asphalt decanter plant has the characteristics of not being restricted by the construction environment, strong adaptability and extremely low failure rate. If large production is required, multiple units can be assembled.