What are the highlights of Sinoroader slurry sealer truck?

1 Common diseases of asphalt pavement
There are nine phenomena of early damage to asphalt pavement: rutting, cracks, and potholes. These diseases are the most common and serious, and are one of the common quality problems of highway projects.
1.1 Rutting
Rutting refers to the longitudinal strip grooves on the road surface along the wheel tracks, with a depth of more than 1.5cm. Rutting is a strip groove formed by the accumulation of permanent deformation of the road surface under the repeated action of vehicle load. Rutting reduces the smoothness of the road surface. When the rutting reaches a certain depth, due to the accumulation of water in the rutting, it is easy for cars to slide and cause traffic accidents. The main reasons for rutting are unreasonable design and serious overloading of vehicles.
1.2 Cracks
There are three main forms of cracks: longitudinal cracks, transverse cracks and mesh cracks. When cracks occur in asphalt pavement, water seepage occurs, which harms the surface layer and base layer.
1.3 Potholes
Potholes are common early diseases of asphalt pavement, which refer to the road surface being damaged into potholes with a depth of more than 2cm and an area of ??more than 0.04㎡. The main reason for the formation of potholes is that the oil used in vehicle repair or motor vehicles seeps into the road surface, polluting the asphalt mixture and causing it to loosen. The pits are gradually formed by driving and rolling.

Synchronous chip seal is a process technology for treating cracks in asphalt pavement, and it is currently a highway construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical characteristics are? If you don’t know, follow the editor of Sinoroader company to have a look.

1. Preparation before construction
2. Mix
3. Paving
4. Leveling
5. Shutdown
6. Overlap
7. Crush

As we all know, emulsified bitumen is a single-component black viscous liquid that can combine the roadbed and the pavement to improve the performance and service life of the road. So what problems should be paid attention to when using emulsified bitumen? Let’s follow the editor of Sinoroader Group, an emulsified bitumen manufacturer, to learn about it.

As a manufacturer with many years of experience in emulsified bitumen construction, Sinoroader Group believes that everyone needs to pay attention to the following 2 points when using it:

Asphalt used to pave roads. It can be obtained by regular vacuum distillation of crude oil with appropriate properties, and can also be obtained by shallow oxidation of vacuum residue or propane deasphalting process. It can also be prepared by mixing asphalt of different duction and injection degree

Asphalt emulsifier is an emulsifier that belongs to the category of surfactants and is a raw material for the production of emulsified asphalt.
Emulsifiers are divided into: synthetic emulsifiers, natural emulsifiers, inorganic powder emulsifiers, etc. Currently, synthetic emulsifiers are widely used. Asphalt emulsifier is a type of chemical organically synthesized surfactant.

The heating principle of asphalt decanter equipment is to heat, melt and decanter the asphalt through the heating plate. It is mainly composed of de-barreling box, lifting system, propeller and electrical control system.
The box of asphalt decanter plant is divided into upper and lower chambers. The upper chamber is the asphalt melting chamber, which is densely covered with heat transfer oil heating coils or hot air heating pipes. The asphalt is melted and removed from the barrel by heat. The hoisting hook is installed on the gantry, and a barrel grabber is hung. The asphalt barrel is lifted by the electric winch, and then the asphalt barrel is placed on the guide rail by horizontal movement. Then the propeller pushes the barrel into the upper chamber through two guide rails, and an empty barrel is pushed out at the rear end outlet.
An anti-drip oil tank is provided at the entrance of the asphalt barrel. The asphalt enters the lower chamber of the box and is continuously heated to a temperature of about 100 to be transported, and then pumped into the asphalt tank by the asphalt pump. The lower chamber can also be used as an asphalt heating tank.
The asphalt decanter plant has the characteristics of not being restricted by the construction environment, strong adaptability and extremely low failure rate. If large production is required, multiple units can be assembled.

I believe everyone is familiar with the relevant knowledge about modified bitumen equipment. As users continue to increase its application, we have also talked about it a lot in the above articles and learned that it is mainly engaged in the production of modified bitumen. Production, in order to further enhance users’ understanding of it, professionals summarize its relevant characteristics as follows:

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixing station also needs to be powered on for trial operation before it is officially put into work.

Emulsified asphalt equipment is a special equipment for producing emulsified asphalt. The emulsified asphalt produced by emulsified asphalt equipment is used in many industries. I wonder how much you know about the emulsified asphalt produced by emulsified asphalt equipment. Let’s take a look at them one by one:
Slurry seal is a cold mix asphalt mixture with the advantages of aggregate and asphalt mixing. Under normal circumstances, similar graded slurry seal has a higher modulus than hot mix asphalt mixture, so it is often used to fill road rutting. The higher stability has a higher resistance to deformation. The mixture is usually composed of harder fine aggregate grading and wear-resistant aggregate with high sand equivalent, especially micro-seal and polymer-modified seal. This greatly increases the strength and integrity of the road surface. This makes the road surface have high wear resistance and excellent deformation resistance. Emulsified asphalt emulsion is also easy to use on a mobile slurry seal paver, where mixing and admixtures are used for chemical control to meet maintenance needs.

Modified bitumen equipment uses modified bitumen colloid mill. Its blade has high hardness, high linear speed of the moving disk, and the gap can be adjusted to 0.15mm. It is suitable for processing various polymer-modified bitumens, such as SBS, PE, EVA, etc.

To ensure good operation of asphalt melting equipment and extend its service life, regular maintenance and repairs are required. The following are specific maintenance and repair steps:
First, various parts of the equipment, including heating elements, pipes, valves, etc., need to be inspected regularly to make sure they are not worn or damaged. If any problems are found, they should be repaired or replaced immediately.

The main filter material of stainless steel barrel removal adopts five-layer sintered mesh. Standard five-layer calcination is made by stacking and vacuum calcining five layers of stainless steel barrel removal wire mesh. The stainless steel barrel made of it has corrosion resistance, good water permeability, high compressive strength, easy cleaning and back-cleaning, high filtration precision, hygienic and clean filter material, and stainless steel barrel removal wire mesh does not fall off.
Double-layer metal sintered mesh is a new type of filtration system with high impact toughness and overall rigidity, which is made by stacking and vacuum calcining double-layer stainless steel barrel removal wire mesh products.

Emulsified modified asphalt equipment includes sewage treatment, water storage tank, water metering and verification temperature control system, asphalt storage tank, asphalt external temperature control system, hot water pump soap seasoning system, soap storage tank, soap mixing pump, soap external temperature control system and metering and verification system, filter, hot asphalt mixing pump and metering and verification system, pipeline black anti-static tweezers, emulsified asphalt cooling system and retrieval equipment, product tank and electrical control system.
The whole set of procedures is modularized, and customers can freely match and use according to their needs. The application of each part of the equipment is as follows: Sewage treatment system: Mechanically filter and adsorb the general drinking water to react with epoxy resin to convert the strong drinking water into pure softened water, reduce the water holding capacity, and improve the emulsion effect of asphalt or asphalt concrete.

We need to prepare a lot of work when using modified asphalt equipment. What kind of work do we need to prepare? Next, let me briefly introduce the relevant knowledge points.
1. Heat transfer oil heats and insulates the modified asphalt equipment and nozzle. After spraying, the asphalt pump and nozzle do not need to be cleaned with diesel. Use high-pressure air to press the asphalt in the pipeline and spray pipe back to the tank, and then blow the nozzle; use heat transfer oil to keep warm, so that the pipeline and nozzle are smooth and unobstructed. 2. Various asphalts can be spread: high-viscosity asphalt, hot asphalt, emulsified asphalt, etc.; the spreading width can be freely adjusted, each nozzle can be controlled separately, and the maximum spraying width is up to 6m. Flexible handheld spray guns can be used to spray asphalt on corners. 3. Excellent thermal insulation performance, average cooling ≤1-2℃/h. 4. Convenient loading and unloading function. In addition to filling asphalt from the asphalt tank port, hot asphalt can be sucked out by itself, and external asphalt can also be pumped and transferred. 5. The modified asphalt equipment is evenly spread, and the nozzle design can be used for triple overlapping spraying.
The above are the relevant knowledge points of modified asphalt equipment. I hope the above content can be helpful to everyone. Thank you for your viewing and support. More information will be sorted out for you later. Please pay attention to our website updates.

Preparation items for micro-surfacing slurry sealing: materials, construction machinery (micro-surfacing paver) and other auxiliary equipment.
The micro-surface slurry seal requires emulsified asphalt and stone that meet the standards. The metering system of the micro-surfacing paver needs to be calibrated before construction. The production of emulsified asphalt requires asphalt heating tanks, emulsified asphalt production equipment (capable of producing asphalt content greater than or equal to 60%), and emulsified asphalt finished product tanks. In terms of stone, mineral screening machines, loaders, forklifts, etc. are needed to screen out oversized stones.
The tests required include emulsification test, screening test, mixing test and the equipment and technical personnel required to do these tests.

Analysis of the necessity of emulsified bitumen equipment in modern road construction projects With the acceleration of the construction speed of transportation infrastructure, the construction standards are getting higher and higher, and higher requirements are also put forward for the use of emulsified bitumen in the closed layer of fly ash and the adhesive layer between the new and old ground.

Microsurfacing is a thin layer of overlay placed on old asphalt pavement and is a type of preventive maintenance process. The purpose of microsurfacing is road maintenance. After micro-surface paving, it can repair cracks in the original road surface, waterproof and beautify the road surface.
The construction method of micro surfacing is: using a micro surfacing paver to evenly spread modified emulsified asphalt, a certain grade of mineral materials, water and other additives on the road surface in a certain proportion.

Asphalt spreading trucks are used to spread the permeable oil layer, waterproof layer and bonding layer of the bottom layer of asphalt pavement on high-grade highways. It can also be used in the construction of county and township-level highway asphalt roads that implement layered paving technology. It consists of a car chassis, an asphalt tank, an asphalt pumping and spraying system, a thermal oil heating system, a hydraulic system, a combustion system, a control system, a pneumatic system, and an operating platform.

Classification analysis of emulsion bitumen equipment is used to heat-melt bitumen. According to the actual cutting effect of mechanical equipment, it is loosened into a solution with demulsifier in the form of tiny droplets to form oil-in-water asphalt. Industrial equipment for lotions. Emulsion bitumen equipment can be divided into three types: portable, transportable and mobile according to the equipment, layout and maneuverability of the equipment.

1. When operating an asphalt spreading truck, first check whether the machinery, spreading devices, protective and fire prevention equipment are complete and effective.
2. It is strictly prohibited to use non-specified fuel as the fuel for the heating system. The fuel is not allowed to overflow outside the tank. Generally, the oil level should be 20-30cm lower than the upper end of the overflow pipe.

Synchronous gravel sealing technology refers to the use of special synchronous gravel sealing truck equipment to lay and roll prepared gravel, asphalt and other materials to build a single layer of asphalt gravel wearing layer, which is important for highway pavement. protection of. From the perspective of characteristics, it is simple and easy to implement. It has obvious effects on the prevention of highway diseases, problem solving, later maintenance, and improvement of grade protection. It can also well extend the service life of highways.

When performing bitumen melting, specialized equipment is required. These equipment usually include bitumen melting furnaces, asphalt mixers, asphalt conveying equipment, etc. Among them, the bitumen melting furnace is one of the most advanced equipments, which can heat solid bitumen to liquid state. In addition, asphalt mixers can mix liquid asphalt with stone to make asphalt concrete. , Asphalt conveying equipment can transport asphalt concrete to the construction site. The selection and use of these equipment are of great significance to ensure the quality of bitumen melting and construction efficiency.

In the cold winter, the following points should be noted when using bitumen melter equipment:

1. Keep warm: The bitumen melter equipment needs to be operated indoors or in a place with sunshade facilities, and ensure that the temperature of the bitumen melter and the surrounding environment is kept within an appropriate range.
2. Check the bitumen melting equipment: Before use, the bitumen melter should be checked, including whether the circuit, liquid circuit and other parts of the equipment are working properly, and whether the equipment has leakage, water leakage and other conditions.
3. Pay attention to safety: During operation, protective bitumen melter equipment should be worn to avoid direct contact with hot bitumen. At the same time, avoid overloading the bitumen melter to prevent equipment damage and safety accidents.
4. Control speed: Reasonably control the working speed of the bitumen melting equipment according to weather conditions and road conditions to avoid overheating of the equipment, which may cause the bitumen to flow too quickly or burn.
5. Storage conditions: When not in use, place the equipment in a dry, ventilated and moderately warm place, and ensure that the residue in the equipment is completely cleaned.

What is the overall operation process of bitumen (composition: asphaltene and resin) drum melting equipment?
The bitumen (composition: asphaltene and resin) drum melting equipment produced by our company mainly uses barrel debarking and melting of large barrels of bitumen (definition: the transformation process of materials from solid to liquid), using high-temperature thermal oil as the material (playing a decision-making role substance), used in supporting facilities of high-temperature thermal oil heating equipment. Bitumen drum melter equipment has the functions of barrel delivery, barrel removal, storage, temperature raising, slag discharge, etc. It is an essential product for high-grade highway construction companies. Bitumen drum melter equipment can be used for resin barrel removal. The bitumen drum melter equipment mainly consists of barrel removal shell, hoisting mechanism, hydraulic booster and electrical control system.

The fine surface is made of stone with a single particle size, which has high wear resistance and anti-slip properties. The construction of the fine surface adopts mechanized construction, which requires less manual labor and has the characteristics of fast construction speed, anti-skid and noise reduction.
The special bonding material for fine surfaces produced by Sinoroader Group has the characteristics of good bonding performance and good durability. The specific construction process is roughly as follows:

No matter the application of emulsified asphalt equipment or other related equipment, in the application of appropriate maintenance work, today we introduce professional technicians to do the following 3 points to effectively improve the utilization rate of asphalt equipment:
1. When the emulsified asphalt plant is out of use for a long time, the liquid in the pipeline and storage tank should be discharged, the lid should be sealed, kept clean, and all moving parts are lubricated. When it is used for the first time and disabled for a long time, the rust of the oil tank should be removed, and the water filter should be cleaned regularly.
2. When the outdoor temperature is lower than -5℃, the emulsified asphalt production equipment shall not store the product without insulation device, and it should be discharged in time to avoid freezing and demulsification of emulsified asphalt.
3. The gap between the stator and the rotor of the emulsified asphalt equipment should be checked regularly. When the machine cannot meet the smaller gap requirements, the stator and rotor should be replaced.

Everyone has a side of themselves that they don’t want others to know. As a preventive road maintenance technology, slurry sealing has some shortcomings. do you think so?
Slurry seal is a kind of road protection that uses special equipment to mix emulsified asphalt, water, additives, aggregates, fillers and other ingredients in a certain proportion, and then mixes the slurry mixture onto the original road surface to form a thin layer. Maintenance technology. These are all well known. The editor will not go into details on this.

For users of equipment, the amount of material used is the focus of every user. We should attach great importance to this link in the production process. The following is an analysis of the amount of emulsifier used by Gaoyuan manufacturers.
When emulsified asphalt equipment is emulsifying asphalt, the asphalt temperature is better controlled at above 130°C to have better fluidity; 2. The amount of emulsifier is generally 8-14‰ of emulsified asphalt, that is, 8-14kg per ton of emulsified asphalt (asphalt content is more than 50%), and the temperature is 60-70°C. The emulsifier should be used in the middle and upper limit of the production, 10 kg per ton of emulsified asphalt, or 20 kg per ton of water (asphalt content is 50%); the amount of BE-3 emulsifier is generally 18-25‰ of emulsified asphalt, that is, 18-25kg per ton of emulsified asphalt (asphalt content is more than 50%), and the emulsifier solution temperature is 60-70°C. The emulsifier should be used in the upper and middle limits in the first production to ensure successful production. Use 24 kg per ton of emulsified asphalt, or 48 kg per ton of water (asphalt content is 50%). After the production goes smoothly, the dosage can be reduced according to actual conditions.