What effect does slurry sealing technology have on road maintenance?

How to reduce the energy consumption of emulsified asphalt production equipment is a concern of many users, and is also an issue that many manufacturers attach great importance to. Therefore, today Sinoroader, as a manufacturer of emulsified asphalt production equipment, would like to take this opportunity to share with you how to reduce the production of emulsified asphalt. Equipment energy consumption method.
Since emulsified asphalt appears as a finished product in emulsified asphalt production equipment, and the outlet temperature of ordinary emulsified asphalt is about 85°C, the outlet temperature of emulsified modified asphalt is above 95°C, so there is a lot of latent heat in emulsified asphalt, but emulsified asphalt The production equipment does not make good use of them, but directly enters the finished product tank, allowing the heat to be lost at will, resulting in a waste of energy.

The heating principle of asphalt decanter equipment is to heat, melt and decanter the asphalt through the heating plate. It is mainly composed of de-barreling box, lifting system, propeller and electrical control system.
The box of asphalt decanter plant is divided into upper and lower chambers. The upper chamber is the asphalt melting chamber, which is densely covered with heat transfer oil heating coils or hot air heating pipes. The asphalt is melted and removed from the barrel by heat. The hoisting hook is installed on the gantry, and a barrel grabber is hung. The asphalt barrel is lifted by the electric winch, and then the asphalt barrel is placed on the guide rail by horizontal movement. Then the propeller pushes the barrel into the upper chamber through two guide rails, and an empty barrel is pushed out at the rear end outlet.
An anti-drip oil tank is provided at the entrance of the asphalt barrel. The asphalt enters the lower chamber of the box and is continuously heated to a temperature of about 100 to be transported, and then pumped into the asphalt tank by the asphalt pump. The lower chamber can also be used as an asphalt heating tank.
The asphalt decanter plant has the characteristics of not being restricted by the construction environment, strong adaptability and extremely low failure rate. If large production is required, multiple units can be assembled.

The viscosity of the bitimen melter equipment decreases as the temperature increases during the production process. Its output viscosity is about twice as high as every 12°C increase. During production, the base bitimen melter equipment must first be heated to a liquid state and then emulsified. In order to better integrate the emulsification ability of colloid milling, the viscosity of base bitimen melter is generally controlled to be about 200 cst. The lower the temperature, the higher the viscosity, which increases the pressure on the bitimen melter pump and colloid milling, making emulsification impossible: However, on the other hand, in order to prevent the asphalt debarrel equipment from weaning when the moisture of th

What details should be paid attention to when adding materials to the emulsified bitumen equipment? Speaking of emulsified bitumen equipment, I don’t know how much you know? What should we pay attention to when adding materials?
The black anti-static tweezers grinding wheel of the emulsified bitumen equipment has no heating barrel. Before use, you must first add an appropriate amount of diesel, let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is about 80 to 100 degrees) Open the shut-off valve on the oil pipe and discharge the diesel in the machine. The temperature of the black anti-static tweezers grinding wheel is about 80 to 100 degrees before it can be loaded and put into production. If there is a heating collet, heat the grinding wheel before starting, and then load the materials for production.

In addition to being used according to regulations, modified bitumen equipment should also be maintained regularly in order to effectively extend the service life of modified bitumen equipment. The delivery pump of modified bitumen equipment, as well as its motor and reducer, need to be maintained in accordance with the specifications of the instructions. If the modified bitumen equipment is parked for a long time, the liquid in the tank and pipeline needs to be drained, and each moving component also needs to be filled with grease. The dust in the control box of the modified bitumen equipment needs to be cleaned once every six months. A dust blower can be used to remove dust to prevent dust from entering the machine and damaging parts. The micro powder machine needs to add unsalted butter once for every 100 tons of emulsified bitumen produced.

In our daily life, we can often see emulsified asphalt equipment. Its appearance has brought us great convenience. So what is the difference between its modification process? Below, the editor will give you a brief introduction to the relevant knowledge points.
1. Emulsified asphalt equipment first emulsifies and then modifies: This is a relatively simple way to make modified emulsified asphalt. The production process is to grind hot asphalt and emulsifier soap together through a colloid mill to make ordinary emulsified asphalt, and then add latex-like modifiers to the emulsified asphalt through mechanical stirring to make modified emulsified asphalt. The characteristic of this method is that it does not require high equipment.

Improve the understanding of the importance of preventive maintenance
We should further improve the understanding of the importance of preventive maintenance and raise preventive maintenance to the level of highway asset protection and road protection. At present, leaders at all levels and maintenance departments do not fully understand the significance of preventive maintenance of asphalt pavement. We should deepen our understanding of the important role of preventive maintenance and improve the strategic awareness, initiative and creativity of preventive maintenance. At the same time, the maintenance department should strengthen communication and exchanges with transportation authorities and financial management departments at all levels, so that departments at all levels understand the importance and necessity of preventive maintenance and create conditions for the implementation of preventive maintenance and funding sources. At the same time, it is very necessary to add preventive maintenance to the classification of maintenance projects, which will help the management of leaders at all levels and the implementation of preventive maintenance.
Improve the decision-making and planning of preventive maintenance
According to the decision-making and planning process, reasonably arrange the preventive maintenance of asphalt concrete pavement structure to ensure the safe and stable operation of highway projects throughout the life cycle, and reduce production costs while providing high-quality traffic services. Therefore, the key to preventive maintenance of asphalt concrete pavement structure lies in establishing a scientific decision-making and planning mechanism. The Ministry of Transport proposed in the “13th Five-Year Plan for Highway Maintenance Management Development” that the average annual mileage of preventive maintenance for expressways should not be less than 8%, and that for ordinary national and provincial roads should not be less than 5%. In the actual application process, local governments should also actively summarize experience and propose different preventive maintenance ratios based on the specific conditions of different regions.

Asphalt used to pave roads. It can be obtained by regular vacuum distillation of crude oil with appropriate properties, and can also be obtained by shallow oxidation of vacuum residue or propane deasphalting process. It can also be prepared by mixing asphalt of different duction and injection degree

No matter what product is used, after using it for a period of time, some large and small problems will inevitably arise, which will affect our work, just like the use of asphalt heating equipment will cause problems such as uneven asphalt pavement. We know that for the use of asphalt heating equipment, the construction of asphalt pavement is affected by many factors, including the quality of construction personnel, the quality of roadbed construction, the treatment of the two sections of the bridgehead culvert and the expansion joint of the bridge, the construction of the road subbase and base, the selection of road construction machinery and the quality of road materials. These are the main reasons affecting the flatness of the road surface.
In order to better help customers apply it, professionals introduce the use of asphalt heating equipment. Flatness is an important indicator for measuring the quality of high-grade pavement. Unsmooth pavement will increase driving resistance and cause additional vibrations in the vehicle, which will directly affect the safety and comfort of driving. At the same time, it will aggravate the damage of automobile parts and tires and increase fuel consumption.

The advantages of Sinoroader bitumen decanter equipment over similar domestic equipment are reflected in the following points:
1. The equipment produces 8-10t/hour, with an automatic telescopic sealed container structure. It uses an electric hoist to lift the asphalt barrel at the inlet guide tube. Start to control the hydraulic cart forward button, which will promote the barrel push (push and slide into the barrel). It is a 1300mm hydraulic cylinder with a 7.5-ton top thrust. The device has a beautiful appearance, reasonable layout, compactness, stable performance, and is suitable for production under various industrial and mining conditions.
2. Fast barrel removal: According to the principle of layered heating, it adopts four-layer thermal oil heating technology, a single inlet and outlet, and high thermal efficiency of heating; at the same time, it uses the waste heat of combustion gas for two heatings and efficient use of energy; the barrel body uses high-quality rock wool insulation material.
3. Good environmental protection: closed structure, no pollution.
4. No barrel hanging: The upper part of the asphalt barrel is hot, and each is directly affected by the thermal oil heating pipe. The barrel wall directly receives the heat dissipation of the heating coil, and the barrel is clean and fast, which will not cause waste of asphalt barrel hanging.
5. Strong adaptability: Suitable for imported and domestic barrels, and the deformation of asphalt barrels will not affect production.
6. Good dehydration: Use a large-displacement asphalt pump for internal circulation, stirring, water vapor overflows, and is naturally discharged from the exhaust port. After dehydration, asphalt can be directly used to produce asphalt mixture or used as matrix asphalt.
7. Automatic slag removal: This set of equipment has an automatic slag removal function. The filter device sets the asphalt circulation pipeline through the filter, which can automatically remove the barreled asphalt slag.
8. Safe and reliable: The equipment adopts an automatic control system, an automatic ignition burner import, can automatically control the temperature according to the temperature, and is equipped with corresponding monitoring instruments.
9. Convenient relocation: The whole machine is assembled with large components, which is easy to move and quick to assemble.

The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) Open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

There are many types of emulsified asphalt (composition: asphaltene and resin) equipment. Emulsified asphalt (composition: asphaltene and resin) equipment can be divided into intermittent operation type, semi-continuous operation type, and Continuing the three operating types, what is the knowledge about different types of emulsified asphalt equipment?

Bitumen emulsifier is a surfactant. A surfactant is a compound that reduces the surface tension between two liquids, a gas and a liquid, or a solid and a liquid. Surfactants are mainly used in: detergents, detergents, fabric softeners, wetting agents, emulsifiers, foaming agents, dispersants, adhesives, etc.

The modified asphalt equipment estimates the quality and uniformity of various raw materials from the material pile and conveyor at any time. The modified asphalt equipment checks the soil and oversized gravel, and checks whether there is any leakage in the cold hopper. Estimate whether the mixed material is mixed evenly, whether there is white material, whether the oil-stone ratio is reasonable, and check the concrete segregation of the asphalt mixture and the mixed material.
The modified asphalt equipment checks the control parameters of various basic parameters of the mixing device in the control room, the display values ??of the control screen, and the modified asphalt equipment checks whether the data statistics and display values ??of the computer and printout are consistent. Test the raw material heating temperature and the mixed material entry temperature of the modified asphalt equipment.

1 Common diseases of asphalt pavement
There are nine phenomena of early damage to asphalt pavement: rutting, cracks, and potholes. These diseases are the most common and serious, and are one of the common quality problems of highway projects.
1.1 Rutting
Rutting refers to the longitudinal strip grooves on the road surface along the wheel tracks, with a depth of more than 1.5cm. Rutting is a strip groove formed by the accumulation of permanent deformation of the road surface under the repeated action of vehicle load. Rutting reduces the smoothness of the road surface. When the rutting reaches a certain depth, due to the accumulation of water in the rutting, it is easy for cars to slide and cause traffic accidents. The main reasons for rutting are unreasonable design and serious overloading of vehicles.
1.2 Cracks
There are three main forms of cracks: longitudinal cracks, transverse cracks and mesh cracks. When cracks occur in asphalt pavement, water seepage occurs, which harms the surface layer and base layer.
1.3 Potholes
Potholes are common early diseases of asphalt pavement, which refer to the road surface being damaged into potholes with a depth of more than 2cm and an area of ??more than 0.04㎡. The main reason for the formation of potholes is that the oil used in vehicle repair or motor vehicles seeps into the road surface, polluting the asphalt mixture and causing it to loosen. The pits are gradually formed by driving and rolling.

Synchronized gravel sealing is a process technology for treating cracks in asphalt pavement, and it is currently a road construction and pavement maintenance technology with low energy consumption and high cost performance. Do you know what its six technical features are? If you don’t know, just follow the editor of Sinoroader and take a look.

Asphalt mixture is a kind of composite material, mainly composed of asphalt, coarse aggregate, fine aggregate, mineral powder, some also added polymer and wood cellulose; By these different quality and quantity of materials mixed to form different structures, and have different mechanical properties

Due to the incorporation of a certain proportion of water into the slurry sealing mixture, it is easy to evaporate in the air. After the water is evaporated, it will become dry and hardened. Therefore, after the slurry is formed, it not only looks very similar to fine-grained asphalt concrete, but does not affect the visual appearance of the road. It also has the same technical properties as fine-grained concrete in terms of wear resistance, anti-skid, waterproofing, and smoothness. Slurry seal technology is used in highway pavement maintenance because of its simple construction technology, short construction period, low cost, high quality, wide application, strong adaptability, etc. It is an asphalt with both economy and high efficiency. Pavement maintenance technology is worthy of application and promotion.

The fine surface is made of stone with a single particle size, which has high wear resistance and anti-slip properties. The construction of the fine surface adopts mechanized construction, which requires less manual labor and has the characteristics of fast construction speed, anti-skid and noise reduction.
The special bonding material for fine surfaces produced by Sinoroader Group has the characteristics of good bonding performance and good durability. The specific construction process is roughly as follows:

Is the performance of Sinoroader’s fully automatic emulsified asphalt production equipment stable and unstable? To be honest, whether the performance of a product is stable or not can only be known through practice, right?
Chairman Mao, the great leader of China, once said, “Without practice, there is no right to speak.” Yes, people who have never used it naturally have no right to speak. Now the editor will talk about the fully automatic emulsified asphalt production equipment that I am using!

The bitumen (composition: asphaltene and resin) drum melting machine adopts a self-heating integrated structure, which integrates the thermal oil boiler used in the old asphalt drum melting machine and the barrel removal equipment itself, reducing the volume of the entire equipment and significantly It reduces equipment investment (actual significance: it is the accumulation of future profits), saves the space occupied by the equipment and the logistics cost of switching sites. The combustion chamber is placed inside the equipment itself, which greatly reduces thermal damage and improves heat utilization.

Modified bitumen equipment uses modified bitumen colloid mill. Its blade has high hardness, high linear speed of the moving disk, and the gap can be adjusted to 0.15mm. It is suitable for processing various polymer-modified bitumens, such as SBS, PE, EVA, etc.

Water is one of the raw materials of the modified asphalt storage tank, and it is distributed in various components of the modified asphalt storage tank equipment. According to the components where water is distributed, the anti-cold measures are explained one by one. The water tank of the modified asphalt storage tank, the water inside the water tank is released through the filter valve. Some instruments of the modified asphalt storage tank do not have a filter valve to save the cost of the equipment. The modified asphalt storage tank can only be drained by loosening the flange bolts at the bottom. The water pump of the modified asphalt storage tank mentioned here includes a hot water pump and a circulating water pump. This type of water pump for the modified asphalt storage tank generally uses a pipeline centrifugal pump. There is a sewage outlet at the bottom of the pipeline centrifugal pump. The modified asphalt storage tank pays attention to the sewage treatment of the sewage outlet at the bottom of the pump. The modified asphalt storage tank emulsion tank generally uses a cone bottom. However, in order to better process the modified asphalt storage tank coefficient, the inlet and outlet are usually not placed at the bottom of the modified asphalt storage tank. Emulsion (mostly water) will remain at the bottom of the tank, and this part of the residual liquid in the modified asphalt storage tank must be discharged through the filter valve at the bottom. Emulsion pump for modified asphalt storage tank There are basically two types of emulsion pumps for modified asphalt storage tank equipment on the market, gear pumps or centrifugal water pumps. Gear pumps can only discharge the liquid inside the pump through the connection flange of the pipeline. The centrifugal water pump for modified asphalt storage tanks uses its own sewage outlet for sewage treatment. The first four items of modified asphalt storage tanks with basic knowledge are basically discharged, and the modified asphalt storage tanks will focus on the latter types. Modified asphalt storage tank colloid mill There will also be residual emulsion or water inside the modified asphalt storage tank colloid mill. The gap between the stator and rotor of the colloid mill is within 1mm. If there is a little residual water in the modified asphalt storage tank, it will cause the accident of frozen modified asphalt storage tank. The residue in the colloid mill can be treated by loosening the connection bolts of the finished product pipeline.

Fillers used in emulsion bitumen equipment are generally divided into two types: chemically active and non-chemically active. In the production of emulsion bitumen equipment, it can improve the stability of the slurry mixture, speed up or slow down the demulsification speed, and improve the strength of the sealing layer. When adding chemically active fillers, the reaction and compatibility of the fillers with mineral materials and modified emulsion bitumen should be fully considered.

From the current point of view, road construction machinery has bottomed out and asphalt meltering equipment has risen rapidly. In recent years, highway construction and maintenance departments have a strong awareness of using asphalt mixing equipment, especially in developed coastal areas such as Beijing, Shanghai, Jiangsu, Zhejiang, etc. In addition, these regions have a fast economic growth rate, relatively developed industry, and strong comprehensive economic strength. Therefore, the consumption of asphalt mixing equipments in these regions has always been at the forefront of the country. With the rapid development of highway construction and the increase in demand for asphalt, barreled asphalt has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported asphalt used in high-grade highways is in barrel form, which requires an asphalt meltering equipment with fast melting speed, clean de-barreling, and can prevent asphalt aging. my country’s highway construction has achieved remarkable results, among which mechanized production has contributed greatly. Different types of asphalt mixers and bitumen meltering equipment are selected for the characteristics of large highway pavement construction and tight construction period. With the rapid development of my country’s economy, the further extension of expressways, and the large-scale development of western construction, the central and western regions have become new investment hotspots. While paying attention to the market in the developed eastern regions, domestic road construction machinery manufacturers have also increased their efforts to develop the central and western markets, creating new highlights for the domestic asphalt mixing plants consumer market. In summary, my country’s asphalt mixing plant sales market has begun to move westward with the westward movement of investment hotspots. As the market center of gravity gradually shifts westward, the market in the western region is gradually heating up. The self-heating integrated structure, hot air barrel melting and bitumen barrel flipping technology in the asphalt barrel removal equipment are our company’s self-heating integrated structure. The thermal oil furnace used in the old equipment is perfectly integrated with the asphalt barrel removal equipment body, which reduces the volume of the entire set of equipment, greatly reduces equipment investment, saves equipment space and transfer transportation costs.

Stainless steel bitumen melters use bitumen concrete micro-powder machines. Its blade strength is high, the angular velocity of the moving disc is high, and the gap can be adjusted to 0.15mm. Stainless steel bitumen melters are suitable for the production and processing of various polymer bitumen concrete, such as SBS, PE, EVA, etc.
Stainless steel bitumen melters use independently developed special batching tanks, stainless steel bitumen melter force stirring devices, liquid level meter overflow prevention equipment, granular material dosage and equipment, liquid additive automatic addition equipment and other production key points. It ensures the full-position process guarantee for the stainless steel bitumen melter of the bitumen concrete production line. The stainless steel bitumen melter processing stainless steel bitumen melter rate is significantly increased, and the quality of stainless steel bitumen melters is greatly improved.

How to reduce energy consumption of emulsified asphalt machinery is a concern of many users and many manufacturers. Therefore, today, Sinosun Company, as a manufacturer of emulsified asphalt equipment, would like to take this opportunity to share with you the method of reducing energy consumption of emulsified asphalt machinery.
Since emulsified asphalt appears as a finished product in emulsified asphalt machinery, and the outlet temperature of ordinary emulsified asphalt is about 85℃, and the outlet temperature of emulsified modified asphalt is above 95℃, there is a lot of latent heat in emulsified asphalt, but the emulsified asphalt equipment does not make good use of them, but directly enters the finished product tank, allowing heat to be lost at will, resulting in energy waste.

Emulsified modified asphalt equipment is classified according to the production process and can be divided into three types: intermittent emulsified modified asphalt equipment, semi-continuous emulsified modified asphalt equipment, and continuous emulsified modified asphalt equipment. During the production of emulsified modified asphalt equipment, demulsifier, acid, water, and latex modified materials are blended in a soap mixing tank, and then pumped into the asphalt into the colloid mill. After a can of soap is used up, the soap is redispensed, and then the production of the next can is completed.
The emulsified modified asphalt equipment mentioned here includes hot water pumps and circulation pumps. This type of centrifugal water pump generally uses a pipeline centrifugal pump. There is a sewage outlet at the bottom of the pipeline centrifugal pump. Pay attention to the sewage outlet at the bottom of the emulsified modified asphalt equipment pump. The water in the water tank is released through the filter valve. Some emulsified modified asphalt equipment does not have a filter valve to save equipment costs, so it can only be emptied by loosening the flange bolts at the bottom. There are basically two methods of moisturizing emulsion pumps for emulsified modified asphalt equipment on the market, gear oil pumps or centrifugal water pumps. The gear oil pump can only drain the liquid in the pump through the connecting flange of the pipeline. The centrifugal water pump carries out sewage treatment through its own sewage outlet.
When used in the production of emulsified modified asphalt equipment, depending on the modified material technology, the latex pipeline can be connected in front of the colloid mill or behind the colloid mill, or there may be no latex pipeline and it must be made manually. Add the required amount of latex into the soap jar.

Asphalt spreading truck is a kind of black ground construction machinery. It is an important equipment in the logistics construction of roads, municipal roads, airports and ports. This equipment is mainly used to spray different types of asphalt on the ground to meet the construction requirements of different levels of ground oil permeable layer, sticky layer, left and right permeable layer, fog permeable layer, etc.