What is the difference between an asphalt mixing plant and an asphalt mixing plant?

The quality of the asphalt mixing plant will be a key factor affecting the quality of the project. After reviewing relevant materials related to the production and construction of asphalt concrete, we summarized some cases of failures in asphalt concrete mixing stations during construction and analyzed the reasons.
1. Unstable output and low production efficiency of asphalt mixing plants
(1) Improper proportioning. The mix ratio of asphalt concrete is divided into target mix ratio and production mix ratio. Among them, the target mix ratio controls the cold material transportation ratio of sand and gravel materials, and the production mix ratio is the mixing ratio of various types of sand and stone materials in the finished asphalt concrete materials specified in the design. The production mix ratio is determined by the laboratory, which directly determines the off-site grading standard of the finished asphalt concrete. The target mix ratio is set to further ensure the production mix ratio, and can be adjusted appropriately during production according to the actual situation. When the target mix ratio or the production mix ratio is not appropriate, the stones stored in each measurement of the asphalt mixing station will be disproportionate, with some overflowing and some other materials, unable to be weighed in time, and the mixing cylinder will be idling, resulting in reduced output.

As an important production equipment in construction, asphalt mixing plant has high production investment. Therefore, production is very important during use, but daily maintenance is also very important. In addition to regular maintenance, routine maintenance is also essential. The editor of Asphalt Mixing Plant shares some key points of daily maintenance and scheduled maintenance;

Construction safety has always been a major issue, and we cannot let any safety hazard go unnoticed. Especially the use of equipment at the construction site. Asphalt mixing stations are prone to failure. Strengthening the maintenance of this equipment is essential to ensure safe construction at the construction site, improve equipment integrity, reduce equipment failures, and ensure the quality of concrete. The role of neglect.
The composition of the asphalt mixing plant is relatively complex, so during maintenance, classified maintenance should be carried out according to the usage and functions of different parts. Maintenance content can be divided into tank maintenance, winch system maintenance and adjustment, stroke limiter adjustment and maintenance, wire rope and pulley maintenance, lifting hopper maintenance, track and track bracket maintenance, etc.

Asphalt mixing plant is also called asphalt mixture mixing equipment, which is mainly used to produce asphalt mixtures of various specifications. It is an important equipment in projects such as road construction, highway maintenance and airport runway construction. The main components of an asphalt mixing plant include cold material supply system, drying drum, screening system, weighing system, agitator, finished product silo and control system.
The workflow of an asphalt mixing plant is generally as follows:

The development prospects of asphalt mixing plants are very good, and the product competition on the market is also very fierce. When the equipment is used, uneven wear of the supporting wheels and wheel rails often occurs, and sometimes there are some abnormal noises and edge gnawing. The main reason is that after the asphalt mixing station has been working for a period of time, the drying cylinder is exposed to high temperature and friction occurs between the supporting wheel and the wheel rail.
Under the action of drying materials in an asphalt mixing station, the equipment will vibrate violently, which will directly lead to improper adjustment of the gap between the wheel rail and the supporting wheel, or mutual interference between the two. The position is skewed, so the operator needs to add grease to the surface contact positions of the supporting wheel and the calibrating wheel rail after every day’s work.

The mixing speed of asphalt mixing plant equipment is indeed very fast, and the corresponding mixing power must be very high, but the specific amount must be measured in a certain way to determine the scope of use of asphalt mixing equipment. There are many methods to measure the mixing power of asphalt mixing equipment, but the relatively small errors are the motor counter-torque measurement method and the strain measurement method.
When the motor of the asphalt mixing equipment starts running, the electromagnetic moment acting on the motor rotor and the electromagnetic moment acting on the motor stator are equal, but their directions are opposite. Therefore, as long as the torque acting on the stator is measured, the torque on the rotor can be obtained, and the actual mixing torque is obtained after deducting the friction torque on the rotor bearing.
On the premise of knowing the torque and mixing speed, the mixing power of the asphalt mixing equipment can be calculated. This is the so-called motor counter-torque measurement method, which is relatively simple and suitable for smaller mixing systems.

1.During the operation of asphalt mixing station equipment, in addition to ensuring that the asphalt mixing station equipment is in good condition, it should also be equipped with a mineral moisture content detector and a finished material tester, and the relevant data should be frequently tested for the operator to adjust the operation in time, so as to keep the equipment in good condition.
2. In addition to affecting production capacity, the moisture content of mineral materials is also the main factor that determines fuel consumption. Additional material sheds should be added.
3. Before operation, all working parts and devices of the asphalt mixing station equipment should be fully checked to see if they are intact and normal. If there is a problem, it must be properly handled before operation, and it is forbidden to operate with illness.

Any kind of mechanical equipment must go through precise design, testing and other processes before it can be manufactured, and the same is true for asphalt mixing stations. According to the survey, the following stages are necessary for any asphalt mixing plant.
First of all, the main technical parameters of the product to be designed must be determined according to market needs, so construction market research, data analysis and other links are indispensable. Secondly, the ideal working principle and the plan to realize this principle will be determined through innovative conception and optimization screening. , a schematic diagram of the overall design scheme should also be given.

Asphalt mixing plant, also known as asphalt concrete mixing plant, asphalt mixing equipment. Refers to a complete set of equipment used for mass production of asphalt concrete. According to the mixing method, it can be divided into intermittent type and continuous type; according to the transportation method, it can be divided into fixed type, semi-fixed type and mobile type.

Safety is the key point for any piece of equipment, and asphalt mixers are of course no exception. What I want to share with you is the knowledge in this area, that is, the safe operation specifications of asphalt mixers. You might as well pay attention to it.
In order to prevent the asphalt mixer from moving during work, the equipment should be placed in a flat position as much as possible, and at the same time, use square wood to pad the front and rear axles so that the tires are elevated. At the same time, the asphalt mixer must be provided with secondary leakage protection, and it can only be started after the inspection, trial operation and other aspects are qualified.

The actual operation steps of drying drum of asphalt mixing equipment: 1. Pay attention to routine inspection; 2. Proper operation steps; 3. Effective maintenance.
Drying drum is a cylindrical device specially used for heating and drying stones in asphalt mixing equipment. Proper application and maintenance of drying drum can maximize the performance of drying drum, increase its service life and reduce application cost. Let’s take a look at the actual operation steps below.
1. Pay attention to routine inspections
The asphalt mixing equipment drying drum has been tested and inspected before leaving the factory, but it will be subjected to vibration and vibration during transportation to the construction site. A comprehensive inspection should be carried out before use: check whether all anchor bolts are tightened; whether all key pins are properly driven; whether all drive devices are adjusted according to the manufacturer’s instructions; whether all pipe connections are appropriate and whether the three-way joints are reliable; whether the entire equipment is fully lubricated; start the motor and check whether all parts can rotate steadily in the correct rotation direction; whether the pressure gauge can work normally and whether the valve is adjusted to the correct working pressure; whether the burner ignition mechanism is available and whether the gate valve is open.
2. Correct operation steps
After the equipment is started, it is recommended to control the machine manually at the beginning, and then switch to the automatic control mode after achieving the required production volume and pouring temperature. The stone should be dried and have a stable moisture content as much as possible so that the stone can maintain a stable final temperature when passing through the drying drum. If the stones delivered to the drying drum change frequently and the moisture content changes each time, the burner should be adjusted frequently to compensate for these changes.
The stones directly from the crushed stone have a relatively constant moisture content, while the stones from the outdoor storage yard have a higher moisture content, and the moisture content of different piles varies greatly. Therefore, it is best for the stones to come from the same source.

Asphalt mixing equipment is also divided into fixed and mobile types. There are still big differences between the two to a certain extent. Let’s take a look at the design of mobile asphalt mixing equipment. What advantages can bring to the equipment?

Certain failures cannot be avoided during the use of the asphalt mixing plant. For example, a malfunction of the cold material feeding device may cause the asphalt mixing plant to shut down. This may be due to a malfunction in the asphalt mixing plant or due to gravel or foreign matter being trapped under the cold material belt.

Speaking of asphalt mixing plants, we are not unfamiliar with them. This is a unit equipment specially used for asphalt mixing. In fact, what we really lack understanding of is its gas system. Even the accumulated failures that often occur in the gas system of asphalt mixing plants are not very clear. Facts have proved that only by properly maintaining the various systems of the equipment can efficient production and good benefits be achieved.
The following are four types of gas system failures that often occur in asphalt mixing plants. Let’s analyze the causes of the problems behind the failures one by one.

Asphalt mixing plant is a very practical engineering machinery. Especially in the road construction process, it plays an irreplaceable role. Due to its importance, in addition to ensuring its own quality, the use and maintenance of the equipment must be carried out normally. Let’s learn about the daily maintenance requirements of asphalt mixing plants.

Synchronous gravel sealing in road maintenance can quickly improve road driving performance, repair anti-skid performance, smoothness, etc. It is used in preventive maintenance and is also one of the methods of low-grade road pavement construction. Synchronous gravel seal has the advantages of high strength, rough surface, non-slip, impermeable, good durability, and prevention of water mist when driving on rainy days. The so-called synchronous gravel sealing layer is to use special equipment, namely the synchronous gravel sealing truck and the bonding material (modified asphalt or modified emulsified asphalt) to be spread simultaneously on the road surface, and the single layer of asphalt wear is formed by natural driving or rolling with a road roller. layer, mainly used as asphalt surface layer.

Mechanism to avoid asphalt damage in asphalt mixing plant
1. Asphalt operators should undergo physical examination. Anyone suffering from conjunctivitis, skin disease or allergic reaction to asphalt should not engage in asphalt work.
2. Asphalt operators must apply protective ointment on exposed parts of their skin, and a first aid kit should be provided on the construction site.
3. The factory uniforms and protective equipment of asphalt operators are stored in a centralized manner and are prohibited from being worn home or entering collective dormitories.
4. The transfer of lumpy asphalt should usually be carried out at night and on cloudy days, especially during hot seasons. Small machinery should be used for loading and unloading, and it should not be lifted and transported directly by hand.

The asphalt mixing equipment mentioned here may also refer to an asphalt concrete mixing plant. At present, asphalt mixing equipment generally uses a complete set of equipment for mixing. So what are the benefits of using a complete set of equipment?
1. More effective.
In today’s industrial production, a complete set of asphalt mixing equipment can help improve production efficiency and ensure product quality. This is why even in a mixing plant, the equipment used is a complete set of equipment.
2. Ensure quality.
When mixing asphalt, a certain ratio is set. For this type of asphalt liquid used in different occasions, its ratio control has strict requirements. It is necessary to determine its mixing method and mixing time to ensure that the asphalt liquid is consistent with the production site. One of the advantages of a mixing plant is that the quality can be effectively controlled.
3. It can be sampled.
After mixing at the mixing plant, the quality inspector can sample and inspect to ensure that the mixed asphalt liquid meets the use requirements.
In short, asphalt mixing equipment will use a complete set of equipment, mainly to facilitate the later asphalt to meet production needs. Through the mixing plant, the mixing time and feeding sequence can be better controlled, so that the mixed product can meet different use requirements. And after using the archiving equipment, effective spot checks can be carried out, which can better ensure that the quality meets the construction requirements.

At present, the assembly and installation technology of large-scale asphalt concrete mixing equipment in high-grade highway construction is gradually improving. In order to improve work efficiency, it is necessary to analyze the pretreatment agent for the selection and matching of large-scale mixing equipment and auxiliary equipment, and clarify the installation and commissioning of asphalt stations. With the continuous change of highway construction methods, it is necessary to adopt production equipment according to the requirements of the development of the times. Intermittent asphalt mixing equipment is a widely used road construction equipment with the characteristics of simple operation and high work efficiency. Relevant staff are required to master the installation, construction and management methods of mixing equipment.

Modified Bitumen

Determining the material is a necessary stage in the design process of asphalt mixing equipment, and it is also one of the most critical links, because the material will be directly related to the use effect and service life of the entire equipment. Generally, when we determine the machine material, we usually base it on the characteristics of the working medium, and the same is certainly true for asphalt mixing equipment.

Asphalt mixing plant is a very practical engineering machinery. Especially in the road construction process, it plays an irreplaceable role. Due to its importance, in addition to ensuring its own quality, the use and maintenance of the equipment must be carried out normally. Let’s learn about the daily maintenance requirements of asphalt mixing plants.

It is inevitable that the asphalt mixing plant will have insufficient pumping force during use. In fact, during the construction process, as long as the asphalt mixing station is operated in accordance with regulations, and the accessories are cleaned and replaced in time, the asphalt mixing plant will generally not have insufficient pumping force. Now the editor of the asphalt mixing station manufacturer briefly introduces the common solutions to insufficient pumping force of asphalt mixing plant as follows.

Asphalt mixing plant is one of the main equipment for producing asphalt concrete. It can mix asphalt, gravel, cement and other materials together in a certain proportion to obtain the products required for highway construction. In order to ensure its operating effect, the asphalt mixer plant also needs to be powered on for trial operation before it is officially put into work.
At the beginning of the test run, first run a single motor, and at the same time check whether the current, steering, insulation and mechanical transmission parts are operating normally. After confirming that each motor and mechanical transmission parts are operating correctly, conduct a joint trial run. During the entire process, it is necessary to conduct patrol inspections of key parts. If any abnormal noise is found, the cause should be identified and eliminated in a timely manner.

1: The site should be located on higher ground and away from residential areas and densely populated areas.
2: The venue should consider the transportation distance and choose a location with convenient transportation.
3: Determine the website construction plan according to the terrain

In recent years, asphalt concrete, as a new green building material, is gradually being valued by people because of its excellent performance in saving resources, being environmentally friendly, ensuring the quality of construction projects, and achieving sustainable utilization of resources. The development of asphalt concrete fully embodies my country’s policies to achieve energy conservation and emission reduction, and is also an important measure to promote the development of circular economy.

In fact, asphalt mixing stations are not uncommon in our daily lives. They are mainly a unit of equipment specially designed to mix asphalt. What we really don’t understand is the gas system of the asphalt mixing station. Only correct maintenance And operation can bring out the best production effect. So what are the faults in the gas circuit of asphalt mixing station?
The following three points are the more common gas path failures of asphalt mixing stations:

Safety is the key point for any piece of equipment, and asphalt mixers are of course no exception. What I want to share with you is the knowledge in this area, that is, the safe operation specifications of asphalt mixers. You might as well pay attention to it.

The HMA-B series forced asphalt mixing plant can produce reliable quality asphalt in various proportions. The product technology is mature, the operation is stable, the specifications are complete, the efficiency is high, the output is large, and the finished asphalt quality is good. It is suitable for various sizes and This type of road construction project has more obvious advantages in larger-scale road construction projects and high-grade highway construction projects.