Why is emulsion bitumen manchine said to have less pollution?

The main filter material of stainless steel barrel removal adopts five-layer sintered mesh. Standard five-layer calcination is made by stacking and vacuum calcining five layers of stainless steel barrel removal wire mesh. The stainless steel barrel made of it has corrosion resistance, good water permeability, high compressive strength, easy cleaning and back-cleaning, high filtration precision, hygienic and clean filter material, and stainless steel barrel removal wire mesh does not fall off.
Double-layer metal sintered mesh is a new type of filtration system with high impact toughness and overall rigidity, which is made by stacking and vacuum calcining double-layer stainless steel barrel removal wire mesh products.

After the rubber bitumen storage tank is cleaned, the wood chips are sent to the rubber bitumen storage tank, and the wood chips and the bottom of the rubber bitumen storage tank are wiped with wood chips. The dirt and wood chips in the bitumen tank can be weathered naturally. The rubber bitumen storage tank is not allowed to be damaged. Check the technical specifications of the underwater concrete processing equipment and ventilation equipment.
The bottom of the rubber bitumen storage tank drain pipe is discharged from the drainage pipe, and the waste water is discharged into the empty tank or other containers through the inlet and outlet and the self-draining pipe. Open the Shenzhen manhole into the plastic suction pipe and pave the Shenzhen manhole with asbestos to reduce the discharge of oil and gas. When manually pumping the bottom oil, two people should be operated to improve the labor efficiency of the workers and send the fuel tank to supervision.

During the use of emulsified bitumen equipments, if maintenance is not paid attention to, the cycle will be short, and problems will often occur during use. Only by doing a good job of maintenance can the operation efficiency of the equipment be improved. For example, during maintenance, the following points must be grasped.
It is necessary to regularly check the wear condition of the internal structural components of the mechanical equipment, such as the core feed pipe, the rough jaw plate on the impeller, the cone cap, the wear level of the jaw plate, the rain shield on the circle, and the wear condition. If the wear is more serious, it is necessary to replace or repair it in time. When replacing, it is also necessary to pay attention to the model and specifications, and replace it according to the original components as a reference.

With the rapid development of highway construction and the increase in demand for asphalt, barreled bitumen has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported bitumen used in high-grade highways is in barrel form, which requires an bitumen melter equipment with fast melting speed, clean debarreling, and prevention of asphalt aging.
The upper part of the debarreler of the bitumen melter equipment is hotter, and each barrel is directly heated by the heat transfer oil coil. The barrel wall directly bears the heat radiation of the heating coil. The asphalt is cleanly and sensitively debarreled, and there will be no waste of asphalt hanging barrels. According to the principle of layered heating, four-layer heating technology is adopted, with single inlet and single outlet of heat transfer oil, and high thermal efficiency of heating; at the same time, the waste heat of combustion exhaust gas is used for secondary heating, and power is effectively used; the debarreler body is insulated with high-quality rock wool material. It is suitable for various types of imported and domestic barrels, and the deformation of asphalt barrels will not affect production.

Analysis of the necessity of emulsified bitumen equipment in modern road construction projects With the acceleration of the construction speed of transportation infrastructure, the construction standards are getting higher and higher, and higher requirements are also put forward for the use of emulsified bitumen in the closed layer of fly ash and the adhesive layer between the new and old ground.

From the current point of view, road construction machinery has bottomed out and asphalt meltering equipment has risen rapidly. In recent years, highway construction and maintenance departments have a strong awareness of using asphalt mixing equipment, especially in developed coastal areas such as Beijing, Shanghai, Jiangsu, Zhejiang, etc. In addition, these regions have a fast economic growth rate, relatively developed industry, and strong comprehensive economic strength. Therefore, the consumption of asphalt mixing equipments in these regions has always been at the forefront of the country. With the rapid development of highway construction and the increase in demand for asphalt, barreled asphalt has been widely used for its convenient transportation and easy storage. In particular, most of the high-performance imported asphalt used in high-grade highways is in barrel form, which requires an asphalt meltering equipment with fast melting speed, clean de-barreling, and can prevent asphalt aging. my country’s highway construction has achieved remarkable results, among which mechanized production has contributed greatly. Different types of asphalt mixers and bitumen meltering equipment are selected for the characteristics of large highway pavement construction and tight construction period. With the rapid development of my country’s economy, the further extension of expressways, and the large-scale development of western construction, the central and western regions have become new investment hotspots. While paying attention to the market in the developed eastern regions, domestic road construction machinery manufacturers have also increased their efforts to develop the central and western markets, creating new highlights for the domestic asphalt mixing plants consumer market. In summary, my country’s asphalt mixing plant sales market has begun to move westward with the westward movement of investment hotspots. As the market center of gravity gradually shifts westward, the market in the western region is gradually heating up. The self-heating integrated structure, hot air barrel melting and bitumen barrel flipping technology in the asphalt barrel removal equipment are our company’s self-heating integrated structure. The thermal oil furnace used in the old equipment is perfectly integrated with the asphalt barrel removal equipment body, which reduces the volume of the entire set of equipment, greatly reduces equipment investment, saves equipment space and transfer transportation costs.

What key points should be paid attention to when feeding emulsified asphalt equipment? When it comes to emulsified asphalt equipment, I don’t know how much you know about it? What should you pay attention to when adding materials?
The black anti-static tweezers grinding wheel of the emulsified asphalt equipment does not have a heated collet. Before use, you must add the appropriate amount of diesel and let the black anti-static tweezers circulate for 3 to 5 minutes to generate heat (the temperature after operation is 80 ~100 degrees) open the stop valve on the oil delivery pipe to drain the diesel engine in the engine. The temperature of the black anti-static tweezers grinding wheel must be around 80 to 100 degrees before the material can be loaded and put into production. If there is a heated collet, the grinding wheel must be heated before starting, and then the material is loaded and put into production.

When using asphalt melting equipment, you need to pay attention to the following points:
1. The power must be cut off during installation and operation to ensure safety.
2. Before starting operation, check whether all components are normal and have no fault prompts. In particular, the inspection of key parts such as the heater part and the conveyor belt device is particularly important.

The container-type emulsified bitumen equipment hot-melts the base cold-mix colored bitumen and disperses it through the equipment into small cold-mix colored bitumen particles in an aqueous solution containing emulsifier to form a liquid cold-mix colored bitumen material.

Improve the reliability of SBS bitumen emulsion plants: Once you have an established maintenance, it will help to identify problems. This will allow the maintenance plan and time to be carried out at your convenience. Regular maintenance will increase the normal operation time of SBS bitumen emulsification equipment, and it can be used when necessary. Low cost of operation: Imagine an SBS bitumen emulsification plant breaks down during a project. With a protective maintenance plan, such things happen less often because you have taken good care of the SBS bitumen emulsification plant.
If the SBS bitumen emulsification plant wants to maintain normal operation, then in the production process. All stages need to be maintained normal, among which the normality of the circuit system is an important aspect to ensure its smooth operation. Imagine that if there is a problem with the circuit during the on-site operation, it may affect the development of the entire project.
For users, of course, they don’t expect this to happen, so if the SBS bitumen emulsification plant is in the work of using the SBS bitumen emulsification equipment, if there is a circuit problem, it is necessary to take appropriate measures to solve it in time. The following article will give a detailed description of this problem, and the following SBS bitumen emulsification plant can be of benefit to everyone.

Asphalt used to pave roads. It can be obtained by regular vacuum distillation of crude oil with appropriate properties, and can also be obtained by shallow oxidation of vacuum residue or propane deasphalting process. It can also be prepared by mixing asphalt of different duction and injection degree

1. Observation: Pay attention to the dynamics of the road surface after milling (three to four days), and pave the milled and roughened road surface in time when paving conditions are met.
2. On-site mixing: During construction and production, a sealing slurry truck should be used for on-site mixing. Through the metering equipment of the sealing truck and on-site operation by a robot, it is ensured that emulsified asphalt, water, mineral materials, fillers, etc. can be mixed according to a certain proportion. , stir through the mixing box, and the paving thickness is not higher than the roughing depth.

Water is one of the raw materials of the modified asphalt storage tank, and it is distributed in various components of the modified asphalt storage tank equipment. According to the components where water is distributed, the anti-cold measures are explained one by one. The water tank of the modified asphalt storage tank, the water inside the water tank is released through the filter valve. Some instruments of the modified asphalt storage tank do not have a filter valve to save the cost of the equipment. The modified asphalt storage tank can only be drained by loosening the flange bolts at the bottom. The water pump of the modified asphalt storage tank mentioned here includes a hot water pump and a circulating water pump. This type of water pump for the modified asphalt storage tank generally uses a pipeline centrifugal pump. There is a sewage outlet at the bottom of the pipeline centrifugal pump. The modified asphalt storage tank pays attention to the sewage treatment of the sewage outlet at the bottom of the pump. The modified asphalt storage tank emulsion tank generally uses a cone bottom. However, in order to better process the modified asphalt storage tank coefficient, the inlet and outlet are usually not placed at the bottom of the modified asphalt storage tank. Emulsion (mostly water) will remain at the bottom of the tank, and this part of the residual liquid in the modified asphalt storage tank must be discharged through the filter valve at the bottom. Emulsion pump for modified asphalt storage tank There are basically two types of emulsion pumps for modified asphalt storage tank equipment on the market, gear pumps or centrifugal water pumps. Gear pumps can only discharge the liquid inside the pump through the connection flange of the pipeline. The centrifugal water pump for modified asphalt storage tanks uses its own sewage outlet for sewage treatment. The first four items of modified asphalt storage tanks with basic knowledge are basically discharged, and the modified asphalt storage tanks will focus on the latter types. Modified asphalt storage tank colloid mill There will also be residual emulsion or water inside the modified asphalt storage tank colloid mill. The gap between the stator and rotor of the colloid mill is within 1mm. If there is a little residual water in the modified asphalt storage tank, it will cause the accident of frozen modified asphalt storage tank. The residue in the colloid mill can be treated by loosening the connection bolts of the finished product pipeline.

Asphalt melting equipment follows the continuous development of urbanization. Whether in rural areas or in big cities, you can see a lot of construction sites, among which it is inevitable that asphalt melting equipment is set up nearby. Asphalt melting equipment manufacturers, whether large or small asphalt melting equipment or relatively large and small, although it is just a simple mechanical equipment, but to move or transport it, it is a small matter, and there are many places that require attention.
The technical level of the asphalt melting equipment disassembly and assembly team directly affects the disassembly and assembly progress of the asphalt melting equipment; improve on-site supervision, reasonably organize disassembly and assembly machinery and equipment and workers, try to avoid cross-operation, and promote the disassembly and assembly process to consume less manpower and machinery shifts to do a good job in the transportation of asphalt melting equipment; ensure that the asphalt melting equipment is not damaged and the prefabricated components are not missed.

Precautions during the production of emulsified bitumen equipment. How much do you know about this information? Let’s learn more about it:
When the emulsified bitumen equipment is in production, the viscosity of the bitumen decreases with the increase of temperature. For every 12℃ increase, its dynamic viscosity decreases by about one time. During production, the base bitumen should be heated to liquid state before emulsification. In addition, in order to adapt to the emulsification capacity of the colloid mill, the base bitumen dynamic viscosity is generally controlled to be about 200cst. The lower the temperature, the higher the viscosity, which increases the burden on the bitumen pump and the colloid mill, making it difficult to emulsify; but on the other hand, in order to prevent the demulsification caused by excessive vaporization and evaporation of water in the finished product during the production of emulsified bitumen, it is impossible to heat the base bitumen temperature too high. Generally, the finished product temperature at the outlet of the colloid mill should be controlled to be less than 85℃.

The difficulty of emulsified bitumen equipment itself, because general bitumen also has different classifications, in the production and processing of emulsified bitumen equipment bitumen concrete, it is necessary to pay attention to whether the common raw materials are the common bitumen and ensure the quality. Check the black antistatic tweezers of emulsified bitumen equipment asphalt concrete machine equipment emulsified bitumen equipment.
If the gap of the black antistatic medical tweezers bitumen concrete micro-powder machine of emulsified bitumen equipment is enlarged after long-term use, then we can adjust it and continue to process it. Emulsified bitumen equipment is a relatively simple difficulty.

The viscosity of the drum bitumen decanter equipment decreases as the temperature increases during the production process. Its output viscosity is about twice as high as every 12°C increase. During production, the base bitumen decanter equipment must first be heated to a liquid state and then emulsified. In order to better integrate the emulsification ability of colloid milling, the viscosity of base bitumen decanter is generally controlled to be about 200 cst. The lower the temperature, the higher the viscosity, which increases the pressure on the bitumen decanter pump and colloid milling, making emulsification impossible: However, on the other hand, in order to prevent the bitumen decanter equipment from weaning when the moisture of the finished product evaporates, it is impossible to heat the base asphalt barrel removal temperature too high, and generally use a colloid grinding inlet and outlet system. The finished product temperature should be below 85°C.

Except for the first application, for enterprises whose block asphalt melting equipment license has expired and continue to engage in the production and operation of block asphalt melting equipment, they should apply for the relevant matters of postponement and renewal 45 working days before the expiration of the license.
The block asphalt melting equipment should first prepare the block asphalt melting equipment application materials, and then submit an application for postponement and renewal to the municipal environmental protection bureau. According to the production and operation of the block asphalt melting equipment and environmental protection work of the applicant enterprise, the municipal environmental protection bureau of the district where the block asphalt melting equipment is located will provide a review opinion in the form of a public document.

This set of emulsified asphalt production equipment includes water treatment, water storage tanks, water active metering and temperature control systems, asphalt storage tanks, asphalt external temperature systems, hot water pump soap batching systems, soap temporary storage tanks, soap transfer pumps, soap liquid It consists of external temperature system and metering system, filter, hot asphalt transfer pump and metering system, three-stage pipeline emulsifier, emulsified asphalt cooling system and recovery equipment, product tank and electrical automatic control system.
The entire process is modularly designed, and users can freely combine and select according to their needs. The equipment of each part is used as follows: Water treatment system: Mechanical filtration of ordinary tap water absorbs resin exchange reactions, turning high-hardness tap water into pure soft water and reducing water tension. , enhance the emulsification effect of asphalt or modified asphalt.

● The spreading amount is accurate, and three overlapping asphalt sprayings can be achieved with good uniformity;
● Intelligent control of spreading amount, real-time monitoring of spreading amount and vehicle speed, closed-loop control;
● Full computer touch screen operation, equipped with video monitoring system, the entire work process can be observed at any time;
● Reliable performance, durability and easy operation;

Classification analysis of emulsion bitumen equipment is used to heat-melt bitumen. According to the actual cutting effect of mechanical equipment, it is loosened into a solution with demulsifier in the form of tiny droplets to form oil-in-water asphalt. Industrial equipment for lotions. Emulsion bitumen equipment can be divided into three types: portable, transportable and mobile according to the equipment, layout and maneuverability of the equipment.

As we all know, emulsified bitumen is a single-component black viscous liquid that can combine the roadbed and the pavement to improve the performance and service life of the road. So what problems should be paid attention to when using emulsified bitumen? Let’s follow the editor of Sinoroader Group, an emulsified bitumen manufacturer, to learn about it.

As a manufacturer with many years of experience in emulsified bitumen construction, Sinoroader Group believes that everyone needs to pay attention to the following 2 points when using it:

Modified material bitumen stripper, if the definition is simple, is an bitumen stripper. If described in detail, modified materials such as rubber powder or other fillers are added to the bitumen stripper, or an bitumen stripper is used to Block chemical substances such as photooxygen catalysis. The first is to change the chemical composition of the bitumen stripper, and the second is to use modified materials to equip the stripper with a certain spatial network structure, thereby improving its performance. Modified bitumen strippers mainly include vulcanized rubber and thermoplastic polyurethane elastomer modified bitumen strippers, plastic and anti-corrosion coating modified bitumen strippers and polymer modified bitumen strippers.

According to statistics, among the high-grade highways that have been built and opened to traffic in my country, about 80% are asphalt pavements. However, with the development of time, the influence of various climatic and environmental factors, and the high-intensity driving load, the asphalt pavement will have different degrees of degradation or damage. Pavement maintenance is to take effective technical means to slow down this degradation, so that the pavement can provide good service quality during its service life.

The requirements for SBS asphalt emulsification equipment are very high. The micro powder machine must have a sufficiently large driving force and can bear the condensation type. Because the temperature requirements of the emulsion SBS asphalt process are relatively high, the emulsified asphalt should be passed through a heat exchanger before feeding to reduce the emulsified asphalt temperature to below 90°C to prevent the emulsified asphalt from breaking due to excessive temperature.
The application scope of SBS modified emulsified asphalt is very wide. According to the nature of the construction, it can be used in new construction, renovation, and reconstruction projects; according to the nature of the project, it can be used in overhaul, equipment overhaul, and maintenance projects. Among them, the actual application projects include micro-surfacing, cold regeneration, cold mixing and cold paving, adhesive layer, permeable oil, slurry seal, gravel permeable layer, fog permeable layer, road moisture-proofing, SBS membrane, ground seam filling, and all other projects that can use emulsified asphalt.

Microsurfacing is a thin layer of overlay placed on old asphalt pavement and is a type of preventive maintenance process. The purpose of microsurfacing is road maintenance. After micro-surface paving, it can repair cracks in the original road surface, waterproof and beautify the road surface.
The construction method of micro surfacing is: using a micro surfacing paver to evenly spread modified emulsified asphalt, a certain grade of mineral materials, water and other additives on the road surface in a certain proportion.

Modified (rubber powder) bitumen equipment, one of the road maintenance equipment. It is a kind of equipment that measures, mixes and develops SBS, rubber powder and asphalt.
Modified (rubber powder) bitumen equipment is a set of wet modification processing technology, which mainly consists of modified material metering and promotion, bitumen rapid heating, asphalt metering, high-intensity mixing tank, mixed material transfer pump, development tank, colloid mill, Control system and other components.

When performing bitumen melting, specialized equipment is required. These equipment usually include bitumen melting furnaces, asphalt mixers, asphalt conveying equipment, etc. Among them, the bitumen melting furnace is one of the most advanced equipments, which can heat solid bitumen to liquid state. In addition, asphalt mixers can mix liquid asphalt with stone to make asphalt concrete. , Asphalt conveying equipment can transport asphalt concrete to the construction site. The selection and use of these equipment are of great significance to ensure the quality of bitumen melting and construction efficiency.

The hydraulic bitumen decanter equipment produced by our company uses thermal oil as the heat carrier and has its own burner for heating. The thermal oil heats, melts, debarks and dehydrates the asphalt through the heating coil. This device can ensure that the asphalt does not age, and has the advantages of high thermal efficiency, fast barrel loading/unloading speed, improved labor intensity, and reduced environmental pollution.

The asphalt spreading truck is an intelligent high-tech product that specializes in spreading emulsified asphalt, diluted asphalt, hot asphalt, heavy traffic asphalt and modified asphalt. It is used in highway construction and highway maintenance projects, and can be used for the construction of upper and lower seals, permeable layers, waterproof layers, bonding layers, asphalt surface treatment, asphalt penetration pavements, fog seals and other projects of different grades of highway pavements. , can also be used for the transportation of liquid asphalt or other heavy oil. So what are the advantages of Qiangguomeng’s asphalt spreader trucks?